From: bugzilla-daemon@bugzilla.kernel.org
To: cpufreq@vger.kernel.org
Subject: [Bug 16436] ath5k (AR5001) does not work after resume and fails with "ath5k phy0: gain calibration timeout"
Date: Mon, 14 May 2012 22:46:45 +0000 (UTC) [thread overview]
Message-ID: <20120514224645.B26BB11FCE7@bugzilla.kernel.org> (raw)
In-Reply-To: <bug-16436-12968@https.bugzilla.kernel.org/>
https://bugzilla.kernel.org/show_bug.cgi?id=16436
--- Comment #43 from Stoian Ivanov <sdr@mail.bg> 2012-05-14 22:46:45 ---
Managed to grabb a ath_info with "broken" state of the driver. This is with
cpufreq completely disabled from menuconfig.
sdr@hristo ~/tmp/ath_info $ cat info_in_error.log
-==Device Information==-
MAC Revision: 2413 (0x78)
Device type: 2
2GHz PHY Revision: 2413 (0x56)
/============== EEPROM Information =============\
| EEPROM Version: 5.3 | EEPROM Size: 16 kbit |
| EEMAP: 2 | Reg. Domain: 0x809C |
|================= Capabilities ================|
| 802.11a Support: no | Turbo-A disabled: no |
| 802.11b Support: yes | Turbo-G disabled: yes |
| 802.11g Support: yes | 2GHz XR disabled: no |
| RFKill Support: no | 5GHz XR disabled: no |
| 32kHz Crystal: no | |
\===============================================/
/=========================================================\
| Calibration data common for all modes |
|=========================================================|
| CCK/OFDM gain delta: 1 |
| CCK/OFDM power delta: 251 |
| Scaled CCK delta: 5 |
| 2GHz Antenna gain: 1 |
| 5GHz Antenna gain: 0 |
| Turbo 2W maximum dBm: 38 |
| Target power start: 0x17c |
| EAR Start: 0x1d6 |
\=========================================================/
/=========================================================\
| Calibration data for 802.11b operation |
|=========================================================|
| I power: 0x00 | Q power: 0x00 |
| Use fixed bias: 0x00 | Max turbo power: 0x00 |
| Max XR power: 0x00 | Switch Settling Time: 0x23 |
| Tx/Rx attenuation: 0x1c | TX end to XLNA On: 0x00 |
| TX end to XPA Off: 0x00 | TX end to XPA On: 0x07 |
| 62db Threshold: 0x1c | XLNA gain: 0x0c |
| XPD: 0x01 | XPD gain: 0x0a |
| I gain: 0x00 | Tx/Rx margin: 0x19 |
| False detect backoff: 0x00 | Noise Floor Threshold: -1 |
| ADC desired size: -38 | PGA desired size: -80 |
|=========================================================|
| Antenna control 0: 0x00 | Antenna control 1: 0x02 |
| Antenna control 2: 0x25 | Antenna control 3: 0x25 |
| Antenna control 4: 0x21 | Antenna control 5: 0x21 |
| Antenna control 6: 0x01 | Antenna control 7: 0x26 |
| Antenna control 8: 0x26 | Antenna control 9: 0x22 |
| Antenna control 10: 0x22 | Antenna control 11: 0x00 |
|=========================================================|
| Octave Band 0: 0 | db 0: 0 |
| Octave Band 1: 3 | db 1: 5 |
| Octave Band 2: 0 | db 2: 0 |
| Octave Band 3: 0 | db 3: 0 |
\=========================================================/
/============== Per rate power calibration ===========\
| Freq | 1Mbit/s | 2Mbit/s | 5.5Mbit/s | 11Mbit/s |
|======|============|==========|===========|==========|
| 2412 | 19.01 | 19.01 | 19.01 | 19.01 |
|======|============|==========|===========|==========|
| 2484 | 19.01 | 19.01 | 19.01 | 19.01 |
\=====================================================/
/====================== Per channel power calibration ===================\
| Freq | pwr_i | pwr_0 | pwr_1 | pwr_2 | pwr_3 |
| | pddac_i | pddac_0 | pddac_1 | pddac_2 | pddac_3 |
|======|=========|=============|=============|=============|=============|
| 2412 | | | | | |
|------|---------|-------------|-------------|-------------|-------------|
| | 0 | 4.00 | 8.50 | 13.00 | 0.00 |
| | 7 | 16 | 37 | 75 | 0 |
|------|---------|-------------|-------------|-------------|-------------|
| | 10 | 14.00 | 18.00 | 22.00 | 25.00 |
| | 12 | 22 | 41 | 69 | 101 |
|======|=========|=============|=============|=============|=============|
| 2472 | | | | | |
|------|---------|-------------|-------------|-------------|-------------|
| | 0 | 4.00 | 8.50 | 13.00 | 0.00 |
| | 9 | 19 | 44 | 89 | 0 |
|------|---------|-------------|-------------|-------------|-------------|
| | 10 | 14.00 | 18.50 | 22.50 | 25.00 |
| | 14 | 25 | 47 | 79 | 111 |
\========================================================================/
/=========================================================\
| Calibration data for 802.11g operation |
|=========================================================|
| I power: 0x00 | Q power: 0x10 |
| Use fixed bias: 0x01 | Max turbo power: 0x26 |
| Max XR power: 0x26 | Switch Settling Time: 0x31 |
| Tx/Rx attenuation: 0x1c | TX end to XLNA On: 0x00 |
| TX end to XPA Off: 0x00 | TX end to XPA On: 0x0e |
| 62db Threshold: 0x1c | XLNA gain: 0x0c |
| XPD: 0x01 | XPD gain: 0x0a |
| I gain: 0x00 | Tx/Rx margin: 0x19 |
| False detect backoff: 0x00 | Noise Floor Threshold: -1 |
| ADC desired size: -38 | PGA desired size: -80 |
|=========================================================|
| Antenna control 0: 0x00 | Antenna control 1: 0x02 |
| Antenna control 2: 0x25 | Antenna control 3: 0x25 |
| Antenna control 4: 0x21 | Antenna control 5: 0x21 |
| Antenna control 6: 0x01 | Antenna control 7: 0x26 |
| Antenna control 8: 0x26 | Antenna control 9: 0x22 |
| Antenna control 10: 0x22 | Antenna control 11: 0x02 |
|=========================================================|
| Octave Band 0: 0 | db 0: 0 |
| Octave Band 1: 3 | db 1: 5 |
| Octave Band 2: 0 | db 2: 0 |
| Octave Band 3: 0 | db 3: 0 |
\=========================================================/
/==================== Turbo mode infos ===================\
| Switch Settling time: 0x62 | Tx/Rx margin: 0x19 |
| Tx/Rx attenuation: 0x1c | ADC desired size: -32 |
| PGA desired size: -80 | |
\=========================================================/
/============== Per rate power calibration ===========\
| Freq | 6-24Mbit/s | 36Mbit/s | 48Mbit/s | 54Mbit/s |
|======|============|==========|===========|==========|
| 2412 | 19.00 | 18.00 | 17.00 | 16.00 |
|======|============|==========|===========|==========|
| 2437 | 19.00 | 18.00 | 17.00 | 16.00 |
|======|============|==========|===========|==========|
| 2462 | 19.00 | 18.00 | 17.00 | 16.00 |
\=====================================================/
/====================== Per channel power calibration ===================\
| Freq | pwr_i | pwr_0 | pwr_1 | pwr_2 | pwr_3 |
| | pddac_i | pddac_0 | pddac_1 | pddac_2 | pddac_3 |
|======|=========|=============|=============|=============|=============|
| 2412 | | | | | |
|------|---------|-------------|-------------|-------------|-------------|
| | 0 | 4.00 | 8.50 | 13.00 | 0.00 |
| | 6 | 12 | 31 | 68 | 0 |
|------|---------|-------------|-------------|-------------|-------------|
| | 10 | 14.00 | 18.00 | 21.50 | 24.00 |
| | 11 | 20 | 35 | 61 | 86 |
|======|=========|=============|=============|=============|=============|
| 2437 | | | | | |
|------|---------|-------------|-------------|-------------|-------------|
| | 0 | 4.00 | 8.50 | 13.00 | 0.00 |
| | 1 | 11 | 29 | 68 | 0 |
|------|---------|-------------|-------------|-------------|-------------|
| | 10 | 14.00 | 18.50 | 21.50 | 24.50 |
| | 12 | 22 | 37 | 62 | 94 |
|======|=========|=============|=============|=============|=============|
| 2472 | | | | | |
|------|---------|-------------|-------------|-------------|-------------|
| | 0 | 4.00 | 8.50 | 13.00 | 0.00 |
| | 3 | 11 | 29 | 66 | 0 |
|------|---------|-------------|-------------|-------------|-------------|
| | 10 | 14.00 | 18.00 | 22.00 | 24.50 |
| | 11 | 22 | 38 | 65 | 97 |
\========================================================================/
GPIO registers: CR 0x00000003, DO 0x00000001, DI 0x00000011
STA_ID0: 74:ea:3a:d9:a5:c4
STA_ID1: 0x1000c4a5, AP: 0, IBSS: 0, KeyCache Disable: 0
TIMER0: 0x00000030, TBTT: 48, TU: 0x00010030
TIMER1: 0x0007ffff, DMAb: 65535, TU: 0x0000ffff (-49)
TIMER2: 0x01ffffff, SWBA: 65535, TU: 0x003fffff (+4128719)
TIMER3: 0x00000031, ATIM: 49, TU: 0x00010031 (+1)
TSF: 0x00000000001e0162, TSFTU: 1920, TU: 0x00000780
BEACON: 0x00000000
LAST_TSTP: 0xda8c7183
--
Configure bugmail: https://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the assignee for the bug.
next prev parent reply other threads:[~2012-05-14 22:46 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <bug-16436-12968@https.bugzilla.kernel.org/>
2011-04-27 19:19 ` [Bug 16436] ath5k (AR5001) does not work after resume and fails with "ath5k phy0: gain calibration timeout" bugzilla-daemon
2011-06-23 18:41 ` bugzilla-daemon
2011-06-23 18:43 ` bugzilla-daemon
2012-01-18 2:13 ` bugzilla-daemon
2012-05-05 10:36 ` bugzilla-daemon
2012-05-05 10:39 ` bugzilla-daemon
2012-05-07 21:54 ` bugzilla-daemon
2012-05-07 22:11 ` bugzilla-daemon
2012-05-13 14:33 ` bugzilla-daemon
2012-05-14 22:46 ` bugzilla-daemon [this message]
2012-08-29 17:26 ` bugzilla-daemon
2012-11-05 14:20 ` bugzilla-daemon
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20120514224645.B26BB11FCE7@bugzilla.kernel.org \
--to=bugzilla-daemon@bugzilla.kernel.org \
--cc=cpufreq@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.