From mboxrd@z Thu Jan  1 00:00:00 1970
From: marex@denx.de (Marek Vasut)
Date: Wed, 16 May 2012 03:02:40 +0200
Subject: [PATCH 3/8] MXS: Fixup i.MX233 USB base address name
In-Reply-To: <20120516005826.GH29393@b20223-02.ap.freescale.net>
References: <1337070219-3630-1-git-send-email-marex@denx.de>
 <1337070219-3630-4-git-send-email-marex@denx.de>
 <20120516005826.GH29393@b20223-02.ap.freescale.net>
Message-ID: <201205160302.41206.marex@denx.de>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

Dear Richard Zhao,

> On Tue, May 15, 2012 at 10:23:34AM +0200, Marek Vasut wrote:
> > Modify USB EHCI and USB PHY base addresses on the i.MX233 to nicely fit
> > into the whole USB registration scheme.
> > 
> > Based on code by:
> > Tony Lin <tony.lin@freescale.com>
> > 
> > Signed-off-by: Marek Vasut <marex@denx.de>
> > Cc: Chen Peter-B29397 <B29397@freescale.com>
> > Cc: Detlev Zundel <dzu@denx.de>
> > Cc: Fabio Estevam <festevam@gmail.com>
> > Cc: Li Frank-B20596 <B20596@freescale.com>
> > Cc: Linux USB <linux-usb@vger.kernel.org>
> > Cc: Liu JunJie-B08287 <B08287@freescale.com>
> > Cc: Sascha Hauer <s.hauer@pengutronix.de>
> > Cc: Shawn Guo <shawn.guo@linaro.org>
> > Cc: Shi Make-B15407 <B15407@freescale.com>
> > Cc: Stefano Babic <sbabic@denx.de>
> > Cc: Subodh Nijsure <snijsure@grid-net.com>
> > Cc: Wolfgang Denk <wd@denx.de>
> > ---
> > 
> >  arch/arm/mach-mxs/include/mach/mx23.h |    8 ++++----
> >  1 file changed, 4 insertions(+), 4 deletions(-)
> > 
> > diff --git a/arch/arm/mach-mxs/include/mach/mx23.h
> > b/arch/arm/mach-mxs/include/mach/mx23.h index 599094b..7955b75 100644
> > --- a/arch/arm/mach-mxs/include/mach/mx23.h
> > +++ b/arch/arm/mach-mxs/include/mach/mx23.h
> > @@ -64,8 +64,8 @@
> > 
> >  #define MX23_AUART1_BASE_ADDR		(MX23_IO_BASE_ADDR + 0x06c000)
> >  #define MX23_AUART2_BASE_ADDR		(MX23_IO_BASE_ADDR + 0x06e000)
> >  #define MX23_DUART_BASE_ADDR		(MX23_IO_BASE_ADDR + 0x070000)
> > 
> > -#define MX23_USBPHY_BASE_ADDR		(MX23_IO_BASE_ADDR + 0x07c000)
> > -#define MX23_USBCTRL_BASE_ADDR		(MX23_IO_BASE_ADDR + 0x080000)
> > +#define MX23_USBPHY0_BASE_ADDR		(MX23_IO_BASE_ADDR + 0x07c000)
> > +#define MX23_USBCTRL0_BASE_ADDR		(MX23_IO_BASE_ADDR + 0x080000)
> 
> Why not migrate to DT?

When it's mainline, sure ... right now, I wanted to make sure these patches can 
be tested without much problems.

> 
> Thanks
> Richard
> 
> >  #define MX23_DRAM_BASE_ADDR		(MX23_IO_BASE_ADDR + 0x0e0000)
> >  
> >  #define MX23_IO_P2V(x)			MXS_IO_P2V(x)
> > 
> > @@ -89,8 +89,8 @@
> > 
> >  #define MX23_INT_SPDIF_ERROR		10
> >  #define MX23_INT_SAIF1_IRQ		10
> >  #define MX23_INT_SAIF2_IRQ		10
> > 
> > -#define MX23_INT_USB_CTRL		11
> > -#define MX23_INT_USB_WAKEUP		12
> > +#define MX23_INT_USB0			11
> > +#define MX23_INT_USB0_WAKEUP		12
> > 
> >  #define MX23_INT_GPMI_DMA		13
> >  #define MX23_INT_SSP1_DMA		14
> >  #define MX23_INT_SSP1_ERROR		15

Best regards,
Marek Vasut