From: Grant Likely <grant.likely@secretlab.ca>
To: Peter Ujfalusi <peter.ujfalusi@ti.com>,
Linus Walleij <linus.walleij@linaro.org>
Cc: linux-kernel@vger.kernel.org, linux-omap@vger.kernel.org
Subject: Re: [PATCH v2 1/3] gpio: twl4030: Introduce private structure to store variables needed runtime
Date: Wed, 19 Dec 2012 17:02:54 +0000 [thread overview]
Message-ID: <20121219170255.C81133E0C42@localhost> (raw)
In-Reply-To: <1354791127-20545-2-git-send-email-peter.ujfalusi@ti.com>
On Thu, 6 Dec 2012 11:52:05 +0100, Peter Ujfalusi <peter.ujfalusi@ti.com> wrote:
> Move most of the global variables inside a private structure and allocate
> it dynamically.
>
> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Applied, thanks
g.
> ---
> drivers/gpio/gpio-twl4030.c | 82 +++++++++++++++++++++++++++------------------
> 1 file changed, 50 insertions(+), 32 deletions(-)
>
> diff --git a/drivers/gpio/gpio-twl4030.c b/drivers/gpio/gpio-twl4030.c
> index 55b4fe4..c092739 100644
> --- a/drivers/gpio/gpio-twl4030.c
> +++ b/drivers/gpio/gpio-twl4030.c
> @@ -49,11 +49,6 @@
> * There are also two LED pins used sometimes as output-only GPIOs.
> */
>
> -
> -static struct gpio_chip twl_gpiochip;
> -static int twl4030_gpio_base;
> -static int twl4030_gpio_irq_base;
> -
> /* genirq interfaces are not available to modules */
> #ifdef MODULE
> #define is_module() true
> @@ -72,11 +67,20 @@ static int twl4030_gpio_irq_base;
> /* Data structures */
> static DEFINE_MUTEX(gpio_lock);
>
> -/* store usage of each GPIO. - each bit represents one GPIO */
> -static unsigned int gpio_usage_count;
> +struct gpio_twl4030_priv {
> + struct gpio_chip gpio_chip;
> + int irq_base;
> +
> + unsigned int usage_count;
> +};
>
> /*----------------------------------------------------------------------*/
>
> +static inline struct gpio_twl4030_priv *to_gpio_twl4030(struct gpio_chip *chip)
> +{
> + return container_of(chip, struct gpio_twl4030_priv, gpio_chip);
> +}
> +
> /*
> * To configure TWL4030 GPIO module registers
> */
> @@ -193,10 +197,6 @@ static int twl4030_get_gpio_datain(int gpio)
> u8 base = 0;
> int ret = 0;
>
> - if (unlikely((gpio >= TWL4030_GPIO_MAX)
> - || !(gpio_usage_count & BIT(gpio))))
> - return -EPERM;
> -
> base = REG_GPIODATAIN1 + d_bnk;
> ret = gpio_twl4030_read(base);
> if (ret > 0)
> @@ -209,6 +209,7 @@ static int twl4030_get_gpio_datain(int gpio)
>
> static int twl_request(struct gpio_chip *chip, unsigned offset)
> {
> + struct gpio_twl4030_priv *priv = to_gpio_twl4030(chip);
> int status = 0;
>
> mutex_lock(&gpio_lock);
> @@ -252,7 +253,7 @@ static int twl_request(struct gpio_chip *chip, unsigned offset)
> }
>
> /* on first use, turn GPIO module "on" */
> - if (!gpio_usage_count) {
> + if (!priv->usage_count) {
> struct twl4030_gpio_platform_data *pdata;
> u8 value = MASK_GPIO_CTRL_GPIO_ON;
>
> @@ -266,16 +267,18 @@ static int twl_request(struct gpio_chip *chip, unsigned offset)
> status = gpio_twl4030_write(REG_GPIO_CTRL, value);
> }
>
> +done:
> if (!status)
> - gpio_usage_count |= (0x1 << offset);
> + priv->usage_count |= BIT(offset);
>
> -done:
> mutex_unlock(&gpio_lock);
> return status;
> }
>
> static void twl_free(struct gpio_chip *chip, unsigned offset)
> {
> + struct gpio_twl4030_priv *priv = to_gpio_twl4030(chip);
> +
> if (offset >= TWL4030_GPIO_MAX) {
> twl4030_led_set_value(offset - TWL4030_GPIO_MAX, 1);
> return;
> @@ -283,10 +286,10 @@ static void twl_free(struct gpio_chip *chip, unsigned offset)
>
> mutex_lock(&gpio_lock);
>
> - gpio_usage_count &= ~BIT(offset);
> + priv->usage_count &= ~BIT(offset);
>
> /* on last use, switch off GPIO module */
> - if (!gpio_usage_count)
> + if (!priv->usage_count)
> gpio_twl4030_write(REG_GPIO_CTRL, 0x0);
>
> mutex_unlock(&gpio_lock);
> @@ -301,14 +304,19 @@ static int twl_direction_in(struct gpio_chip *chip, unsigned offset)
>
> static int twl_get(struct gpio_chip *chip, unsigned offset)
> {
> + struct gpio_twl4030_priv *priv = to_gpio_twl4030(chip);
> int status = 0;
>
> + if (!(priv->usage_count & BIT(offset)))
> + return -EPERM;
> +
> if (offset < TWL4030_GPIO_MAX)
> status = twl4030_get_gpio_datain(offset);
> else if (offset == TWL4030_GPIO_MAX)
> status = cached_leden & LEDEN_LEDAON;
> else
> status = cached_leden & LEDEN_LEDBON;
> +
> return (status < 0) ? 0 : status;
> }
>
> @@ -333,12 +341,14 @@ static void twl_set(struct gpio_chip *chip, unsigned offset, int value)
>
> static int twl_to_irq(struct gpio_chip *chip, unsigned offset)
> {
> - return (twl4030_gpio_irq_base && (offset < TWL4030_GPIO_MAX))
> - ? (twl4030_gpio_irq_base + offset)
> + struct gpio_twl4030_priv *priv = to_gpio_twl4030(chip);
> +
> + return (priv->irq_base && (offset < TWL4030_GPIO_MAX))
> + ? (priv->irq_base + offset)
> : -EINVAL;
> }
>
> -static struct gpio_chip twl_gpiochip = {
> +static struct gpio_chip template_chip = {
> .label = "twl4030",
> .owner = THIS_MODULE,
> .request = twl_request,
> @@ -424,8 +434,14 @@ static int __devinit gpio_twl4030_probe(struct platform_device *pdev)
> {
> struct twl4030_gpio_platform_data *pdata = pdev->dev.platform_data;
> struct device_node *node = pdev->dev.of_node;
> + struct gpio_twl4030_priv *priv;
> int ret, irq_base;
>
> + priv = devm_kzalloc(&pdev->dev, sizeof(struct gpio_twl4030_priv),
> + GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> /* maybe setup IRQs */
> if (is_module()) {
> dev_err(&pdev->dev, "can't dispatch IRQs from modules\n");
> @@ -445,12 +461,13 @@ static int __devinit gpio_twl4030_probe(struct platform_device *pdev)
> if (ret < 0)
> return ret;
>
> - twl4030_gpio_irq_base = irq_base;
> + priv->irq_base = irq_base;
>
> no_irqs:
> - twl_gpiochip.base = -1;
> - twl_gpiochip.ngpio = TWL4030_GPIO_MAX;
> - twl_gpiochip.dev = &pdev->dev;
> + priv->gpio_chip = template_chip;
> + priv->gpio_chip.base = -1;
> + priv->gpio_chip.ngpio = TWL4030_GPIO_MAX;
> + priv->gpio_chip.dev = &pdev->dev;
>
> if (node)
> pdata = of_gpio_twl4030(&pdev->dev);
> @@ -481,23 +498,23 @@ no_irqs:
> * is (still) clear if use_leds is set.
> */
> if (pdata->use_leds)
> - twl_gpiochip.ngpio += 2;
> + priv->gpio_chip.ngpio += 2;
>
> - ret = gpiochip_add(&twl_gpiochip);
> + ret = gpiochip_add(&priv->gpio_chip);
> if (ret < 0) {
> dev_err(&pdev->dev, "could not register gpiochip, %d\n", ret);
> - twl_gpiochip.ngpio = 0;
> + priv->gpio_chip.ngpio = 0;
> gpio_twl4030_remove(pdev);
> goto out;
> }
>
> - twl4030_gpio_base = twl_gpiochip.base;
> + platform_set_drvdata(pdev, priv);
>
> if (pdata && pdata->setup) {
> int status;
>
> - status = pdata->setup(&pdev->dev,
> - twl4030_gpio_base, TWL4030_GPIO_MAX);
> + status = pdata->setup(&pdev->dev, priv->gpio_chip.base,
> + TWL4030_GPIO_MAX);
> if (status)
> dev_dbg(&pdev->dev, "setup --> %d\n", status);
> }
> @@ -510,18 +527,19 @@ out:
> static int gpio_twl4030_remove(struct platform_device *pdev)
> {
> struct twl4030_gpio_platform_data *pdata = pdev->dev.platform_data;
> + struct gpio_twl4030_priv *priv = platform_get_drvdata(pdev);
> int status;
>
> if (pdata && pdata->teardown) {
> - status = pdata->teardown(&pdev->dev,
> - twl4030_gpio_base, TWL4030_GPIO_MAX);
> + status = pdata->teardown(&pdev->dev, priv->gpio_chip.base,
> + TWL4030_GPIO_MAX);
> if (status) {
> dev_dbg(&pdev->dev, "teardown --> %d\n", status);
> return status;
> }
> }
>
> - status = gpiochip_remove(&twl_gpiochip);
> + status = gpiochip_remove(&priv->gpio_chip);
> if (status < 0)
> return status;
>
> --
> 1.8.0
>
--
Grant Likely, B.Sc, P.Eng.
Secret Lab Technologies, Ltd.
next prev parent reply other threads:[~2012-12-19 20:35 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-12-06 10:52 [PATCH v2 0/3] gpio: twl4030: Correct status reporting for outputs Peter Ujfalusi
2012-12-06 10:52 ` Peter Ujfalusi
2012-12-06 10:52 ` [PATCH v2 1/3] gpio: twl4030: Introduce private structure to store variables needed runtime Peter Ujfalusi
2012-12-06 10:52 ` Peter Ujfalusi
2012-12-19 17:02 ` Grant Likely [this message]
2012-12-06 10:52 ` [PATCH v2 2/3] gpio: twl4030: Cache the direction and output states in private data Peter Ujfalusi
2012-12-06 10:52 ` Peter Ujfalusi
2012-12-19 17:03 ` Grant Likely
2012-12-19 20:53 ` Michael Trimarchi
2012-12-19 22:17 ` Grant Likely
2012-12-06 10:52 ` [PATCH v2 3/3] gpio: twl4030: TODO comment to remove the PWMA/B (LEDA/B) handling Peter Ujfalusi
2012-12-06 10:52 ` Peter Ujfalusi
2012-12-19 17:07 ` Grant Likely
2012-12-20 9:23 ` Peter Ujfalusi
2012-12-20 9:23 ` Peter Ujfalusi
2012-12-20 9:45 ` Grant Likely
2012-12-07 8:09 ` [PATCH v2 0/3] gpio: twl4030: Correct status reporting for outputs Linus Walleij
2012-12-12 11:12 ` Peter Ujfalusi
2012-12-12 11:12 ` Peter Ujfalusi
2012-12-12 11:45 ` Grant Likely
2012-12-12 12:47 ` Peter Ujfalusi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20121219170255.C81133E0C42@localhost \
--to=grant.likely@secretlab.ca \
--cc=linus.walleij@linaro.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=peter.ujfalusi@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.