From: Timo Teras <timo.teras@iki.fi>
To: linux-media@vger.kernel.org
Subject: Terratec Grabby hwrev 2
Date: Mon, 25 Mar 2013 19:08:46 +0200 [thread overview]
Message-ID: <20130325190846.3250fe98@vostro> (raw)
I just bought a Terratec Grabby hardware revision 2 in hopes that it
would work on my linux box.
But alas, I got only sound working. It seems that analog video picture
grabbing does not work.
I tried kernels 3.4.34-grsec, 3.7.1 (vanilla), 3.8.2-grsec and
3.9.0-rc4 (vanilla). And all fail the same way - no video data received.
The USB ID is same as on the revision 1 board:
Bus 005 Device 002: ID 0ccd:0096 TerraTec Electronic GmbH
And it is properly detected as Grabby.
It seems that the videobuf2 changes for 3.9.0-rc4 resulted in better
debug logging, and it implies that the application (ffmpeg 1.1.4) is
behaving well: all buffers are allocated, mmapped, queued, streamon
called. But no data is received from the dongle. I also tested mencoder
and it fails in similar manner.
Dmesg (on 3.9.0-rc4) tells after module load the following:
[ 1249.600246] em28xx: New device TerraTec Electronic GmbH TerraTec Grabby @ 480 Mbps (0ccd:0096, inte
rface 0, class 0)
[ 1249.600258] em28xx: Video interface 0 found: isoc
[ 1249.600264] em28xx: DVB interface 0 found: isoc
[ 1249.600443] em28xx: chip ID is em2860
[ 1249.715053] em2860 #0: i2c eeprom 00: 1a eb 67 95 cd 0c 96 00 50 00 11 03 9c 20 6a 32
[ 1249.715084] em2860 #0: i2c eeprom 10: 00 00 06 57 0e 02 00 00 00 00 00 00 00 00 00 00
[ 1249.715110] em2860 #0: i2c eeprom 20: 02 00 01 00 f0 10 01 00 00 00 00 00 5b 00 00 00
[ 1249.715136] em2860 #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 01 01 00 00 00 00 00 00
[ 1249.715161] em2860 #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1249.715186] em2860 #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1249.715211] em2860 #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 32 03 54 00 65 00
[ 1249.715235] em2860 #0: i2c eeprom 70: 72 00 72 00 61 00 54 00 65 00 63 00 20 00 45 00
[ 1249.715261] em2860 #0: i2c eeprom 80: 6c 00 65 00 63 00 74 00 72 00 6f 00 6e 00 69 00
[ 1249.715286] em2860 #0: i2c eeprom 90: 63 00 20 00 47 00 6d 00 62 00 48 00 20 03 54 00
[ 1249.715311] em2860 #0: i2c eeprom a0: 65 00 72 00 72 00 61 00 54 00 65 00 63 00 20 00
[ 1249.715336] em2860 #0: i2c eeprom b0: 47 00 72 00 61 00 62 00 62 00 79 00 48 00 00 00
[ 1249.715361] em2860 #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1249.715385] em2860 #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1249.715410] em2860 #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1249.715435] em2860 #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 1249.715464] em2860 #0: EEPROM ID= 0x9567eb1a, EEPROM hash = 0xd3498090
[ 1249.715470] em2860 #0: EEPROM info:
[ 1249.715475] em2860 #0: AC97 audio (5 sample rates)
[ 1249.715480] em2860 #0: 500mA max power
[ 1249.715487] em2860 #0: Table at 0x06, strings=0x209c, 0x326a, 0x0000
[ 1249.715495] em2860 #0: Identified as Terratec Grabby (card=67)
[ 1250.058076] em2860 #0: Config register raw data: 0x50
[ 1250.076845] em2860 #0: AC97 vendor ID = 0x60f160f1
[ 1250.086814] em2860 #0: AC97 features = 0x60f1
[ 1250.086822] em2860 #0: Unknown AC97 audio processor detected!
[ 1251.116646] em2860 #0: v4l2 driver version 0.1.3
[ 1251.891145] em2860 #0: V4L2 video device registered as video0
[ 1251.891155] em2860 #0: V4L2 VBI device registered as vbi0
[ 1251.891161] em2860 #0: analog set to isoc mode.
[ 1251.891167] em2860 #0: dvb set to isoc mode.
[ 1251.910649] usbcore: registered new interface driver em28xx
Any suggestions how to debug/fix this?
Thanks,
Timo
next reply other threads:[~2013-03-25 17:07 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-03-25 17:08 Timo Teras [this message]
2013-03-25 17:36 ` Terratec Grabby hwrev 2 Mauro Carvalho Chehab
2013-03-25 17:48 ` Timo Teras
2013-03-25 18:32 ` Mauro Carvalho Chehab
2013-03-25 19:12 ` Timo Teras
2013-03-26 8:20 ` Timo Teras
2013-03-27 14:10 ` Timo Teras
2013-03-28 8:52 ` Timo Teras
2013-03-28 12:40 ` Mauro Carvalho Chehab
2013-03-28 13:35 ` Timo Teras
2013-03-28 14:54 ` Timo Teras
2013-05-01 17:11 ` Jon Arne Jørgensen
2013-05-02 7:04 ` Timo Teras
2013-05-03 5:47 ` Timo Teras
2013-05-03 9:13 ` Jon Arne Jørgensen
2013-05-03 11:12 ` Ezequiel Garcia
2013-03-28 15:22 ` Mauro Carvalho Chehab
2013-03-30 9:54 ` Timo Teras
2013-04-01 17:26 ` Frank Schäfer
2013-04-02 5:43 ` Timo Teras
2013-04-02 16:39 ` Frank Schäfer
2013-04-03 8:27 ` Timo Teras
2013-04-05 15:33 ` Frank Schäfer
2013-04-29 12:26 ` Timo Teras
2013-05-03 5:50 ` Timo Teras
2013-05-10 11:04 ` Tomasz Moń
2013-03-27 17:37 ` Frank Schäfer
2013-03-27 17:57 ` Timo Teras
2013-03-27 18:04 ` Timo Teras
2013-03-27 20:12 ` Frank Schäfer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20130325190846.3250fe98@vostro \
--to=timo.teras@iki.fi \
--cc=linux-media@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.