From: Vinod Koul <vinod.koul@intel.com>
To: Lars-Peter Clausen <lars@metafoo.de>
Cc: Ralf Baechle <ralf@linux-mips.org>,
Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>,
Maarten ter Huurne <maarten@treewalker.org>,
linux-mips@linux-mips.org, linux-kernel@vger.kernel.org,
alsa-devel@alsa-project.org
Subject: Re: [PATCH 0/6] Convert JZ4740 to dmaengine
Date: Fri, 21 Jun 2013 19:43:30 +0530 [thread overview]
Message-ID: <20130621141330.GK23141@intel.com> (raw)
In-Reply-To: <1369931105-28065-1-git-send-email-lars@metafoo.de>
On Thu, May 30, 2013 at 06:24:59PM +0200, Lars-Peter Clausen wrote:
> Hi,
>
> This series replaces the custom JZ4740 DMA API with a dmaengine driver. This is
> done in 3 steps:
> 1) Add a dmaengine driver which wraps the custom JZ4740 DMA API
> 2) Update all users of the JZ4740 DMA API to use dmaengine instead
> 3) Remove the custom API and move all direct hardware access to the
> dmaengine driver.
>
> The first two patches in the series also make sure that the clock of the DMA
> core is enabled.
>
> Since the patches in this series depend on each other I'd prefer if they could
> all go through the DMA tree.
>
> There are a few minor changes to the patch 3 in v2 of this series, all other
> patches are identical to v1.
Applied all expect the "ASoC: jz4740: Use the generic dmaengine PCM driver". Can
you rebase that on slave dma-next and resend
Fixed up struct alignment manually in 4th one
--
~Vinod
>
> - Lars
>
> Lars-Peter Clausen (4):
> dma: Add a jz4740 dmaengine driver
> MIPS: jz4740: Register jz4740 DMA device
> ASoC: jz4740: Use the generic dmaengine PCM driver
> MIPS: jz4740: Remove custom DMA API
>
> Maarten ter Huurne (2):
> MIPS: jz4740: Correct clock gate bit for DMA controller
> MIPS: jz4740: Acquire and enable DMA controller clock
>
> arch/mips/include/asm/mach-jz4740/dma.h | 56 ---
> arch/mips/include/asm/mach-jz4740/platform.h | 1 +
> arch/mips/jz4740/Makefile | 2 +-
> arch/mips/jz4740/board-qi_lb60.c | 1 +
> arch/mips/jz4740/clock.c | 2 +-
> arch/mips/jz4740/dma.c | 287 -------------
> arch/mips/jz4740/platform.c | 21 +
> drivers/dma/Kconfig | 6 +
> drivers/dma/Makefile | 1 +
> drivers/dma/dma-jz4740.c | 617 +++++++++++++++++++++++++++
> sound/soc/jz4740/Kconfig | 1 +
> sound/soc/jz4740/jz4740-i2s.c | 48 +--
> sound/soc/jz4740/jz4740-pcm.c | 310 +-------------
> sound/soc/jz4740/jz4740-pcm.h | 20 -
> 14 files changed, 676 insertions(+), 697 deletions(-)
> delete mode 100644 arch/mips/jz4740/dma.c
> create mode 100644 drivers/dma/dma-jz4740.c
> delete mode 100644 sound/soc/jz4740/jz4740-pcm.h
>
> --
> 1.8.2.1
>
--
next prev parent reply other threads:[~2013-06-21 14:13 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-05-30 16:24 [PATCH 0/6] Convert JZ4740 to dmaengine Lars-Peter Clausen
2013-05-30 16:24 ` Lars-Peter Clausen
2013-05-30 16:25 ` [PATCH v2 1/6] MIPS: jz4740: Correct clock gate bit for DMA controller Lars-Peter Clausen
2013-05-30 16:25 ` [PATCH v2 2/6] MIPS: jz4740: Acquire and enable DMA controller clock Lars-Peter Clausen
2013-05-30 16:25 ` [PATCH v2 3/6] dma: Add a jz4740 dmaengine driver Lars-Peter Clausen
2013-05-30 17:12 ` Vinod Koul
2013-05-30 17:12 ` Vinod Koul
2013-05-30 18:46 ` Lars-Peter Clausen
2013-06-10 17:29 ` Lars-Peter Clausen
2013-06-12 5:38 ` Vinod Koul
2013-06-12 12:07 ` Lars-Peter Clausen
2013-06-12 12:07 ` [alsa-devel] " Lars-Peter Clausen
2013-06-21 10:51 ` Vinod Koul
2013-05-30 16:25 ` [PATCH v2 4/6] MIPS: jz4740: Register jz4740 DMA device Lars-Peter Clausen
2013-05-30 17:24 ` Sergei Shtylyov
2013-06-10 17:30 ` Lars-Peter Clausen
2013-05-30 16:25 ` [PATCH v2 5/6] ASoC: jz4740: Use the generic dmaengine PCM driver Lars-Peter Clausen
2013-05-30 16:25 ` [PATCH v2 6/6] MIPS: jz4740: Remove custom DMA API Lars-Peter Clausen
2013-05-30 17:20 ` Vinod Koul
2013-05-30 18:48 ` Lars-Peter Clausen
2013-06-21 14:13 ` Vinod Koul [this message]
-- strict thread matches above, loose matches on Subject: below --
2013-05-23 20:36 [PATCH 0/6] Convert JZ4740 to dmaengine Lars-Peter Clausen
2013-05-23 20:36 ` Lars-Peter Clausen
2013-05-29 9:31 ` Ralf Baechle
2013-05-29 9:31 ` Ralf Baechle
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20130621141330.GK23141@intel.com \
--to=vinod.koul@intel.com \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@kernel.org \
--cc=lars@metafoo.de \
--cc=lgirdwood@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@linux-mips.org \
--cc=maarten@treewalker.org \
--cc=ralf@linux-mips.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.