From: Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>
To: "to-fleischer-zqRNUXuvxA0b1SvskN2V4Q@public.gmane.org"
<to-fleischer-zqRNUXuvxA0b1SvskN2V4Q@public.gmane.org>
Cc: linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
Alexandre Belloni
<alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>,
Fabio Estevam <r49496-KZfg59tc24xl57MIdRCFDg@public.gmane.org>,
Lucas Stach <l.stach-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>,
Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>,
Wolfram Sang <wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org>
Subject: Re: [PATCH] i2c: mxs: Rework the PIO mode operation
Date: Wed, 17 Jul 2013 19:04:00 +0200 [thread overview]
Message-ID: <201307171904.00784.marex@denx.de> (raw)
In-Reply-To: <1UzQet-1Vf4pE0-VM4m3MaA7PGi2rA4ip7KQzlaCuRwF3y+@public.gmane.org>
Dear to-fleischer-zqRNUXuvxA0b1SvskN2V4Q@public.gmane.org,
> Hi,
>
> > > Analyze and rework the PIO mode operation. The PIO mode operation
> > > was unreliable on MX28, by analyzing the bus with LA, the checks for
> > > when data were available or were to be sent were wrong.
> > >
> > > The PIO WRITE has to be completely reworked as it multiple problems.
> > > The MX23 datasheet helped here, see comments in the code for
> > > details.
> > > The problems boil down to:
> > > - RUN bit in CTRL0 must be set after DATA register was written - The
> > > PIO transfer must be 4 bytes long tops, otherwise use
> > > clock stretching.
> > > Both of these fixes are implemented.
> > >
> > > The PIO READ operation can only be done for up to four bytes as we
> > > are unable to read out the data from the DATA register fast enough.
> > >
> > > This patch also tries to document the investigation within the code.
> > >
> > > Signed-off-by: Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>
> > > Cc: Alexandre Belloni <alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> > > Cc: Fabio Estevam <r49496-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
> > > Cc: Lucas Stach <l.stach-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> > > Cc: Shawn Guo <shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
> > > Cc: Wolfram Sang <wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org>
> > > Cc: <to-fleischer-zqRNUXuvxA0b1SvskN2V4Q@public.gmane.org>
> >
> > I so far got confirmation from ALexandre this patch works. Can someone
> > else test it please? I'd like to roll out a final version to close
> > this issue.
>
> sorry, I couldn't test the patch until today on my iMX283 board.
> It works when reading the registers from the temperature sensor TCN75A.
> But it fails when writing less than 7 bytes to the EEPROM (24LC32). Then
> I always get a 'Connection timed out' error in the user space.
Thinking about this, did you correctly configure the EEPROM write sector size? I
think it's 32 bytes for this device.
Best regards,
Marek Vasut
next prev parent reply other threads:[~2013-07-17 17:04 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-07-08 19:46 [PATCH] i2c: mxs: Rework the PIO mode operation Marek Vasut
[not found] ` <1373312807-13227-1-git-send-email-marex-ynQEQJNshbs@public.gmane.org>
2013-07-08 19:49 ` Marek Vasut
2013-07-09 13:21 ` Alexandre Belloni
2013-07-15 2:05 ` Marek Vasut
[not found] ` <201307150405.53110.marex-ynQEQJNshbs@public.gmane.org>
2013-07-15 12:14 ` Lucas Stach
[not found] ` <1373890479.4172.3.camel-WzVe3FnzCwFR6QfukMTsflXZhhPuCNm+@public.gmane.org>
2013-07-15 12:27 ` Marek Vasut
2013-07-15 14:58 ` Shawn Guo
[not found] ` <20130715145836.GB23589-rvtDTF3kK1ictlrPMvKcciBecyulp+rMXqFh9Ls21Oc@public.gmane.org>
2013-07-15 23:25 ` Marek Vasut
2013-07-17 12:16 ` to-fleischer-zqRNUXuvxA0b1SvskN2V4Q
[not found] ` <1UzQet-1Vf4pE0-VM4m3MaA7PGi2rA4ip7KQzlaCuRwF3y+@public.gmane.org>
2013-07-17 16:23 ` Marek Vasut
2013-07-17 17:04 ` Marek Vasut [this message]
[not found] ` <201307171904.00784.marex-ynQEQJNshbs@public.gmane.org>
2013-07-18 19:12 ` Torsten Fleischer
[not found] ` <3767128.gOKkIqK4p5-BVXpyJtzy6LO1Ldfs0Uenw@public.gmane.org>
2013-07-21 21:21 ` Marek Vasut
[not found] ` <201307212321.22207.marex-ynQEQJNshbs@public.gmane.org>
2013-07-28 9:47 ` Torsten Fleischer
2013-07-15 12:43 ` Lucas Stach
[not found] ` <1373892198.4172.17.camel-WzVe3FnzCwFR6QfukMTsflXZhhPuCNm+@public.gmane.org>
2013-07-15 23:24 ` Marek Vasut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=201307171904.00784.marex@denx.de \
--to=marex-ynqeqjnshbs@public.gmane.org \
--cc=alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org \
--cc=l.stach-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org \
--cc=linux-i2c-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=r49496-KZfg59tc24xl57MIdRCFDg@public.gmane.org \
--cc=shawn.guo-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
--cc=to-fleischer-zqRNUXuvxA0b1SvskN2V4Q@public.gmane.org \
--cc=wsa-z923LK4zBo2bacvFa/9K2g@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.