From: moinejf@free.fr (Jean-Francois Moine)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 4/10] drm/i2c: tda998x: don't read write-only registers
Date: Wed, 23 Oct 2013 09:40:58 +0200 [thread overview]
Message-ID: <20131023094058.44f307ac@armhf> (raw)
This patch takes care of the write-only registers of the tda998x.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
---
drivers/gpu/drm/i2c/tda998x_drv.c | 44 +++++++++++-----------
1 file changed, 23 insertions(+), 21 deletions(-)
diff --git a/drivers/gpu/drm/i2c/tda998x_drv.c b/drivers/gpu/drm/i2c/tda998x_drv.c
index 0053a34..d26d521 100644
--- a/drivers/gpu/drm/i2c/tda998x_drv.c
+++ b/drivers/gpu/drm/i2c/tda998x_drv.c
@@ -487,9 +487,9 @@ static void
tda998x_reset(struct tda998x_priv *priv)
{
/* reset audio and i2c master: */
- reg_set(priv, REG_SOFTRESET, SOFTRESET_AUDIO | SOFTRESET_I2C_MASTER);
+ reg_write(priv, REG_SOFTRESET, SOFTRESET_AUDIO | SOFTRESET_I2C_MASTER);
msleep(50);
- reg_clear(priv, REG_SOFTRESET, SOFTRESET_AUDIO | SOFTRESET_I2C_MASTER);
+ reg_write(priv, REG_SOFTRESET, 0);
msleep(50);
/* reset transmitter: */
@@ -842,7 +842,7 @@ tda998x_encoder_mode_set(struct drm_encoder *encoder,
reg_set(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_FIFO);
/* set HDMI HDCP mode off: */
- reg_set(priv, REG_TBG_CNTRL_1, TBG_CNTRL_1_DWIN_DIS);
+ reg_write(priv, REG_TBG_CNTRL_1, TBG_CNTRL_1_DWIN_DIS);
reg_clear(priv, REG_TX33, TX33_HDMI);
reg_write(priv, REG_ENC_CNTRL, ENC_CNTRL_CTL_CODE(0));
@@ -869,38 +869,28 @@ tda998x_encoder_mode_set(struct drm_encoder *encoder,
PLL_SERIAL_2_SRL_PR(rep));
/* set color matrix bypass flag: */
- reg_set(priv, REG_MAT_CONTRL, MAT_CONTRL_MAT_BP);
+ reg_write(priv, REG_MAT_CONTRL, MAT_CONTRL_MAT_BP |
+ MAT_CONTRL_MAT_SC(1));
/* set BIAS tmds value: */
reg_write(priv, REG_ANA_GENERAL, 0x09);
- reg_clear(priv, REG_TBG_CNTRL_0, TBG_CNTRL_0_SYNC_MTHD);
+ reg_write(priv, REG_TBG_CNTRL_0, TBG_CNTRL_0_SYNC_MTHD);
/*
* Sync on rising HSYNC/VSYNC
*/
- reg_write(priv, REG_VIP_CNTRL_3, 0);
- reg_set(priv, REG_VIP_CNTRL_3, VIP_CNTRL_3_SYNC_HS);
+ reg = VIP_CNTRL_3_SYNC_HS;
/*
* TDA19988 requires high-active sync at input stage,
* so invert low-active sync provided by master encoder here
*/
if (mode->flags & DRM_MODE_FLAG_NHSYNC)
- reg_set(priv, REG_VIP_CNTRL_3, VIP_CNTRL_3_H_TGL);
+ reg |= VIP_CNTRL_3_H_TGL;
if (mode->flags & DRM_MODE_FLAG_NVSYNC)
- reg_set(priv, REG_VIP_CNTRL_3, VIP_CNTRL_3_V_TGL);
-
- /*
- * Always generate sync polarity relative to input sync and
- * revert input stage toggled sync at output stage
- */
- reg = TBG_CNTRL_1_TGL_EN;
- if (mode->flags & DRM_MODE_FLAG_NHSYNC)
- reg |= TBG_CNTRL_1_H_TGL;
- if (mode->flags & DRM_MODE_FLAG_NVSYNC)
- reg |= TBG_CNTRL_1_V_TGL;
- reg_write(priv, REG_TBG_CNTRL_1, reg);
+ reg |= VIP_CNTRL_3_V_TGL;
+ reg_write(priv, REG_VIP_CNTRL_3, reg);
reg_write(priv, REG_VIDFORMAT, 0x00);
reg_write16(priv, REG_REFPIX_MSB, ref_pix);
@@ -932,10 +922,22 @@ tda998x_encoder_mode_set(struct drm_encoder *encoder,
/* must be last register set: */
reg_clear(priv, REG_TBG_CNTRL_0, TBG_CNTRL_0_SYNC_ONCE);
+ /*
+ * Always generate sync polarity relative to input sync and
+ * revert input stage toggled sync at output stage
+ */
+ reg = TBG_CNTRL_1_DWIN_DIS | TBG_CNTRL_1_TGL_EN;
+ if (mode->flags & DRM_MODE_FLAG_NHSYNC)
+ reg |= TBG_CNTRL_1_H_TGL;
+ if (mode->flags & DRM_MODE_FLAG_NVSYNC)
+ reg |= TBG_CNTRL_1_V_TGL;
+ reg_write(priv, REG_TBG_CNTRL_1, reg);
+
/* Only setup the info frames if the sink is HDMI */
if (priv->is_hdmi_sink) {
/* We need to turn HDMI HDCP stuff on to get audio through */
- reg_clear(priv, REG_TBG_CNTRL_1, TBG_CNTRL_1_DWIN_DIS);
+ reg &= ~TBG_CNTRL_1_DWIN_DIS;
+ reg_write(priv, REG_TBG_CNTRL_1, reg);
reg_write(priv, REG_ENC_CNTRL, ENC_CNTRL_CTL_CODE(1));
reg_set(priv, REG_TX33, TX33_HDMI);
--
Ken ar c'henta? | ** Breizh ha Linux atav! **
Jef | http://moinejf.free.fr/
reply other threads:[~2013-10-23 7:40 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20131023094058.44f307ac@armhf \
--to=moinejf@free.fr \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.