* [U-Boot] ATMEL AT45DB041D spi flash and gplugd @ 2014-02-09 8:40 Yogi P 2014-02-16 16:38 ` Jagan Teki 0 siblings, 1 reply; 4+ messages in thread From: Yogi P @ 2014-02-09 8:40 UTC (permalink / raw) To: u-boot Hello all, ^ permalink raw reply [flat|nested] 4+ messages in thread
* [U-Boot] ATMEL AT45DB041D spi flash and gplugd 2014-02-09 8:40 [U-Boot] ATMEL AT45DB041D spi flash and gplugd Yogi P @ 2014-02-16 16:38 ` Jagan Teki 2014-02-18 1:25 ` yogi p 0 siblings, 1 reply; 4+ messages in thread From: Jagan Teki @ 2014-02-16 16:38 UTC (permalink / raw) To: u-boot Hi Yogi, On Sun, Feb 9, 2014 at 2:10 PM, Yogi P <yogi.p2182@gmail.com> wrote: > Hello all, > > From following commit spi write/erase times out on gplugd which uses ATMEL > AT45DB041D spi flash. > >>commit f4f51a8ff894d34eb332f0d11f6c73c7bf509848 >>Author: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> >>Date: Wed Oct 2 19:36:58 2013 +0530 >> >> sf: probe: Add support for erase sector selection flag >> >> SECT_4K, SECT_32K and SECT_64K opeartions are performed to >> to specific flash by adding a SECT* flag on respective >> spi_flash_params.flag param. >> >>Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> > > Prior to this patch erase size was same as sector size; which is 64 * 1024 (64k). > This 64K was replaced with 4k and timeout for erase started. > > If following patch is applied write/erase works well (See bottom) on top of > above commit. But similar change on latest git head still has some problem > with spi erase. Does this means CMD_ERASE_64K works on master? Can you verify correctly - because we couldn't find any issues so far as per as the sf_ops code is concern. > diff --git a/drivers/mtd/spi/spi_flash_probe.c b/drivers/mtd/spi/spi_flash_probe.c > index 9c2e115..9e1c4c5 100644 > --- a/drivers/mtd/spi/spi_flash_probe.c > +++ b/drivers/mtd/spi/spi_flash_probe.c > @@ -41,7 +41,7 @@ static const struct spi_flash_params spi_flash_params_table[] = { > #ifdef CONFIG_SPI_FLASH_ATMEL /* ATMEL */ > {"AT45DB011D", 0x1f2200, 0x0, 64 * 1024, 4, SECT_4K}, > {"AT45DB021D", 0x1f2300, 0x0, 64 * 1024, 8, SECT_4K}, > - {"AT45DB041D", 0x1f2400, 0x0, 64 * 1024, 8, SECT_4K}, > + {"AT45DB041D", 0x1f2400, 0x0, 64 * 1024, 8, 0}, > {"AT45DB081D", 0x1f2500, 0x0, 64 * 1024, 16, SECT_4K}, > {"AT45DB161D", 0x1f2600, 0x0, 64 * 1024, 32, SECT_4K}, > {"AT45DB321D", 0x1f2700, 0x0, 64 * 1024, 64, SECT_4K}, > > _______________________________________________ > U-Boot mailing list > U-Boot at lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot thanks! -- Jagan. ^ permalink raw reply [flat|nested] 4+ messages in thread
* [U-Boot] ATMEL AT45DB041D spi flash and gplugd 2014-02-16 16:38 ` Jagan Teki @ 2014-02-18 1:25 ` yogi p 2014-03-17 16:55 ` Jagan Teki 0 siblings, 1 reply; 4+ messages in thread From: yogi p @ 2014-02-18 1:25 UTC (permalink / raw) To: u-boot Hi Jagan, On Sun, Feb 16, 2014 at 10:08 PM, Jagan Teki <jagannadh.teki@gmail.com>wrote: > Hi Yogi, > > On Sun, Feb 9, 2014 at 2:10 PM, Yogi P <yogi.p2182@gmail.com> wrote: > > Hello all, > > > > From following commit spi write/erase times out on gplugd which uses > ATMEL > > AT45DB041D spi flash. > > > >>commit f4f51a8ff894d34eb332f0d11f6c73c7bf509848 > >>Author: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> > >>Date: Wed Oct 2 19:36:58 2013 +0530 > >> > >> sf: probe: Add support for erase sector selection flag > >> > >> SECT_4K, SECT_32K and SECT_64K opeartions are performed to > >> to specific flash by adding a SECT* flag on respective > >> spi_flash_params.flag param. > >> > >>Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> > > > > Prior to this patch erase size was same as sector size; which is 64 * > 1024 (64k). > > This 64K was replaced with 4k and timeout for erase started. > > > > If following patch is applied write/erase works well (See bottom) on top > of > > above commit. But similar change on latest git head still has some > problem > > with spi erase. > > Does this means CMD_ERASE_64K works on master? > No its not working on master. Can you verify correctly - because we couldn't find any issues so far > as per as the sf_ops > code is concern. > Its stopped working from f4f51a8ff894d34eb332f0d11f6c73c7bf509848. But to get it working on this particular commit following patch is needed. But even with this patch, master is broken. Thanks Yogi > > > diff --git a/drivers/mtd/spi/spi_flash_probe.c > b/drivers/mtd/spi/spi_flash_probe.c > > index 9c2e115..9e1c4c5 100644 > > --- a/drivers/mtd/spi/spi_flash_probe.c > > +++ b/drivers/mtd/spi/spi_flash_probe.c > > @@ -41,7 +41,7 @@ static const struct spi_flash_params > spi_flash_params_table[] = { > > #ifdef CONFIG_SPI_FLASH_ATMEL /* ATMEL */ > > {"AT45DB011D", 0x1f2200, 0x0, 64 * 1024, 4, > SECT_4K}, > > {"AT45DB021D", 0x1f2300, 0x0, 64 * 1024, 8, > SECT_4K}, > > - {"AT45DB041D", 0x1f2400, 0x0, 64 * 1024, 8, > SECT_4K}, > > + {"AT45DB041D", 0x1f2400, 0x0, 64 * 1024, 8, > 0}, > > {"AT45DB081D", 0x1f2500, 0x0, 64 * 1024, 16, > SECT_4K}, > > {"AT45DB161D", 0x1f2600, 0x0, 64 * 1024, 32, > SECT_4K}, > > {"AT45DB321D", 0x1f2700, 0x0, 64 * 1024, 64, > SECT_4K}, > > > > _______________________________________________ > > U-Boot mailing list > > U-Boot at lists.denx.de > > http://lists.denx.de/mailman/listinfo/u-boot > > > thanks! > -- > Jagan. > -- Thanks Yogi ^ permalink raw reply [flat|nested] 4+ messages in thread
* [U-Boot] ATMEL AT45DB041D spi flash and gplugd 2014-02-18 1:25 ` yogi p @ 2014-03-17 16:55 ` Jagan Teki 0 siblings, 0 replies; 4+ messages in thread From: Jagan Teki @ 2014-03-17 16:55 UTC (permalink / raw) To: u-boot Hi Yogi, On Tue, Feb 18, 2014 at 6:55 AM, yogi p <yogi.p2182@gmail.com> wrote: > Hi Jagan, > > On Sun, Feb 16, 2014 at 10:08 PM, Jagan Teki <jagannadh.teki@gmail.com> > wrote: >> >> Hi Yogi, >> >> On Sun, Feb 9, 2014 at 2:10 PM, Yogi P <yogi.p2182@gmail.com> wrote: >> > Hello all, >> > >> > From following commit spi write/erase times out on gplugd which uses >> > ATMEL >> > AT45DB041D spi flash. >> > >> >>commit f4f51a8ff894d34eb332f0d11f6c73c7bf509848 >> >>Author: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> >> >>Date: Wed Oct 2 19:36:58 2013 +0530 >> >> >> >> sf: probe: Add support for erase sector selection flag >> >> >> >> SECT_4K, SECT_32K and SECT_64K opeartions are performed to >> >> to specific flash by adding a SECT* flag on respective >> >> spi_flash_params.flag param. >> >> >> >>Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com> >> > >> > Prior to this patch erase size was same as sector size; which is 64 * >> > 1024 (64k). >> > This 64K was replaced with 4k and timeout for erase started. >> > >> > If following patch is applied write/erase works well (See bottom) on top >> > of >> > above commit. But similar change on latest git head still has some >> > problem >> > with spi erase. >> >> Does this means CMD_ERASE_64K works on master? > > No its not working on master. > >> Can you verify correctly - because we couldn't find any issues so far >> as per as the sf_ops >> code is concern. > > Its stopped working from f4f51a8ff894d34eb332f0d11f6c73c7bf509848. > But to get it working on this particular commit following patch is needed. > > But even with this patch, master is broken. > > Thanks > Yogi >> >> >> > diff --git a/drivers/mtd/spi/spi_flash_probe.c >> > b/drivers/mtd/spi/spi_flash_probe.c >> > index 9c2e115..9e1c4c5 100644 >> > --- a/drivers/mtd/spi/spi_flash_probe.c >> > +++ b/drivers/mtd/spi/spi_flash_probe.c >> > @@ -41,7 +41,7 @@ static const struct spi_flash_params >> > spi_flash_params_table[] = { >> > #ifdef CONFIG_SPI_FLASH_ATMEL /* ATMEL */ >> > {"AT45DB011D", 0x1f2200, 0x0, 64 * 1024, 4, >> > SECT_4K}, >> > {"AT45DB021D", 0x1f2300, 0x0, 64 * 1024, 8, >> > SECT_4K}, >> > - {"AT45DB041D", 0x1f2400, 0x0, 64 * 1024, 8, >> > SECT_4K}, >> > + {"AT45DB041D", 0x1f2400, 0x0, 64 * 1024, 8, >> > 0}, >> > {"AT45DB081D", 0x1f2500, 0x0, 64 * 1024, 16, >> > SECT_4K}, >> > {"AT45DB161D", 0x1f2600, 0x0, 64 * 1024, 32, >> > SECT_4K}, >> > {"AT45DB321D", 0x1f2700, 0x0, 64 * 1024, 64, >> > SECT_4K}, I'm recollecting bug information you pointed, please correct what I'm saying here. Current tree for AT45DB041D part has configured flash->erase_cmd = CMD_ERASE_4K; flash->erase_size = 4096; The same configuration is not working for your board, is that true? Did you see working tree in earlier tag releases? -- Jagan. ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2014-03-17 16:55 UTC | newest] Thread overview: 4+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2014-02-09 8:40 [U-Boot] ATMEL AT45DB041D spi flash and gplugd Yogi P 2014-02-16 16:38 ` Jagan Teki 2014-02-18 1:25 ` yogi p 2014-03-17 16:55 ` Jagan Teki
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.