From: Fengguang Wu <fengguang.wu@intel.com>
To: Stefani Seibold <stefani@seibold.net>
Cc: "H. Peter Anvin" <hpa@linux.intel.com>,
linux-kernel@vger.kernel.org,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Subject: Re: [x86, vdso] BUG: unable to handle kernel paging request at d34bd000
Date: Fri, 7 Mar 2014 18:36:49 +0800 [thread overview]
Message-ID: <20140307103649.GA21708@localhost> (raw)
In-Reply-To: <1394186248.28066.42.camel@wall-e.seibold.net>
On Fri, Mar 07, 2014 at 10:57:28AM +0100, Stefani Seibold wrote:
> Hi Fengguang,
>
> did you test the config i had sent to you?
Stefani, here is the result with your config. It goes on to another
bug. I repeated it twice and it's reproducible.
This kernel is build with gcc 4.6.3 on commit
4dea8e4824b363c53f320d328040d7c6c5921419 ("x86, vdso: Add 32 bit VDSO
time support for 32 bit kernel").
wfg@bee ~/linux/obj-compiletest% kvm-0day.sh arch/x86/boot/bzImage
early console in setup code
Probing EDD (edd=off to disable)... ok
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.14.0-rc5-00009-g4dea8e4 (wfg@bee) (gcc version 4.6.3 (Debian 4.6.3-1) ) #6 SMP Fri Mar 7 18:30:39 CST 2014
[ 0.000000] KERNEL supported cpus:
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] CPU: vendor_id 'GenuineIntel' unknown, using generic init.
[ 0.000000] CPU: Your system may be unstable.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000000fffdfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000fffe000-0x000000000fffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
[ 0.000000] debug: ignoring loglevel setting.
[ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[ 0.000000] SMBIOS 2.4 present.
[ 0.000000] DMI: Bochs Bochs, BIOS Bochs 01/01/2011
[ 0.000000] Hypervisor detected: KVM
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0xfffe max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: write-back
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0080000000 mask FF80000000 uncachable
[ 0.000000] 1 disabled
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] Scan for SMP in [mem 0x00000000-0x000003ff]
[ 0.000000] Scan for SMP in [mem 0x0009fc00-0x0009ffff]
[ 0.000000] Scan for SMP in [mem 0x000f0000-0x000fffff]
[ 0.000000] found SMP MP-table at [mem 0x000f1840-0x000f184f] mapped at [800f1840]
[ 0.000000] mpc: f1850-f193c
[ 0.000000] initial memory mapped: [mem 0x00000000-0x02bfffff]
[ 0.000000] Base memory trampoline at [8009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x0f800000-0x0fbfffff]
[ 0.000000] [mem 0x0f800000-0x0fbfffff] page 4k
[ 0.000000] BRK [0x02790000, 0x02790fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x08000000-0x0f7fffff]
[ 0.000000] [mem 0x08000000-0x0f7fffff] page 4k
[ 0.000000] BRK [0x02791000, 0x02791fff] PGTABLE
[ 0.000000] BRK [0x02792000, 0x02792fff] PGTABLE
[ 0.000000] BRK [0x02793000, 0x02793fff] PGTABLE
[ 0.000000] BRK [0x02794000, 0x02794fff] PGTABLE
[ 0.000000] BRK [0x02795000, 0x02795fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x07ffffff]
[ 0.000000] [mem 0x00100000-0x07ffffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x0fc00000-0x0fffdfff]
[ 0.000000] [mem 0x0fc00000-0x0fffdfff] page 4k
[ 0.000000] RAMDISK: [mem 0x0fce6000-0x0ffeffff]
[ 0.000000] ACPI: RSDP 000f16b0 000014 (v00 BOCHS )
[ 0.000000] ACPI: RSDT 0fffe3f0 000034 (v01 BOCHS BXPCRSDT 00000001 BXPC 00000001)
[ 0.000000] ACPI: FACP 0fffff80 000074 (v01 BOCHS BXPCFACP 00000001 BXPC 00000001)
[ 0.000000] ACPI: DSDT 0fffe430 001137 (v01 BXPC BXDSDT 00000001 INTL 20100528)
[ 0.000000] ACPI: FACS 0fffff40 000040
[ 0.000000] ACPI: SSDT 0ffff6a0 000899 (v01 BOCHS BXPCSSDT 00000001 BXPC 00000001)
[ 0.000000] ACPI: APIC 0ffff5b0 000080 (v01 BOCHS BXPCAPIC 00000001 BXPC 00000001)
[ 0.000000] ACPI: HPET 0ffff570 000038 (v01 BOCHS BXPCHPET 00000001 BXPC 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] mapped APIC to ffff9000 ( fee00000)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 255MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 0fffe000
[ 0.000000] low ram: 0 - 0fffe000
[ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00
[ 0.000000] kvm-clock: cpu 0, msr 0:fffb001, boot clock
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x0fffdfff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0x0fffdfff]
[ 0.000000] On node 0 totalpages: 65436
[ 0.000000] free_area_init_node: node 0, pgdat 8200a2e0, node_mem_map 8f951028
[ 0.000000] DMA zone: 40 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] Normal zone: 600 pages used for memmap
[ 0.000000] Normal zone: 61438 pages, LIFO batch:15
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0xb008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] mapped APIC to ffff9000 ( fee00000)
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 0, APIC INT 02
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level)
[ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 05, APIC ID 0, APIC INT 05
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 0, APIC INT 09
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level)
[ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0a, APIC ID 0, APIC INT 0a
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level)
[ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0b, APIC ID 0, APIC INT 0b
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 0, APIC INT 01
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 0, APIC INT 03
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 0, APIC INT 04
[ 0.000000] ACPI: IRQ5 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 0, APIC INT 06
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 0, APIC INT 07
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 0, APIC INT 08
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ10 used by override.
[ 0.000000] ACPI: IRQ11 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 0, APIC INT 0c
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 0, APIC INT 0d
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 0, APIC INT 0e
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 0, APIC INT 0f
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] mapped IOAPIC to ffff8000 (fec00000)
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] e820: [mem 0x10000000-0xfeffbfff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on KVM
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 330 pages/cpu @8f6bd000 s1338976 r0 d12704 u1351680
[ 0.000000] pcpu-alloc: s1338976 r0 d12704 u1351680 alloc=330*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] kvm-clock: cpu 0, msr 0:fffb001, primary cpu clock
[ 0.000000] KVM setup async PF for cpu 0
[ 0.000000] kvm-stealtime: cpu 0, msr f6bf540
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64796
[ 0.000000] Kernel command line: debug sched_debug apic=debug ignore_loglevel earlyprintk=ttyS0,115200 sysrq_always_enabled panic=10 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 vga=normal root=/dev/ram0 rw
[ 0.000000] sysrq: sysrq always enabled.
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 228784K/261744K available (11650K kernel code, 875K rwdata, 4076K rodata, 1920K init, 5512K bss, 32960K reserved, 0K highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffa93000 - 0xfffff000 (5552 kB)
[ 0.000000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.000000] vmalloc : 0x907fe000 - 0xff3fe000 (1772 MB)
[ 0.000000] lowmem : 0x80000000 - 0x8fffe000 ( 255 MB)
[ 0.000000] .init : 0x82039000 - 0x82219000 (1920 kB)
[ 0.000000] .data : 0x81b60dce - 0x82037fe0 (4956 kB)
[ 0.000000] .text : 0x81000000 - 0x81b60dce (11651 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU debugfs-based tracing is enabled.
[ 0.000000] Hierarchical RCU autobalancing is disabled.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:2304 nr_irqs:512 16
[ 0.000000] CPU 0 irqstacks, hard=8f00a000 soft=8f00c000
[ 0.000000] ACPI: Core revision 20131218
[ 0.000000] ACPI: All ACPI Tables successfully acquired
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] console [ttyS0] enabled
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3807 kB
[ 0.000000] per task-struct memory footprint: 1920 bytes
[ 0.000000] ------------------------
[ 0.000000] | Locking API testsuite:
[ 0.000000] ----------------------------------------------------------------------------
[ 0.000000] | spin |wlock |rlock |mutex | wsem | rsem |
[ 0.000000] --------------------------------------------------------------------------
[ 0.000000] A-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-B-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-B-C-C-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-C-A-B-C deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-B-C-C-D-D-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-C-D-B-D-D-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-C-D-B-C-D-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] double unlock: ok | ok | ok | ok | ok | ok |
[ 0.000000] initialize held: ok | ok | ok | ok | ok | ok |
[ 0.000000] bad unlock order: ok | ok | ok | ok | ok | ok |
[ 0.000000] --------------------------------------------------------------------------
[ 0.000000] recursive read-lock: | ok | |failed|
[ 0.000000] recursive read-lock #2: | ok | |failed|
[ 0.000000] mixed read-write-lock: |failed| |failed|
[ 0.000000] mixed write-read-lock: |failed| |failed|
[ 0.000000] --------------------------------------------------------------------------
[ 0.000000] hard-irqs-on + irq-safe-A/12:failed|failed| ok |
[ 0.000000] soft-irqs-on + irq-safe-A/12:failed|failed| ok |
[ 0.000000] hard-irqs-on + irq-safe-A/21:failed|failed| ok |
[ 0.000000] soft-irqs-on + irq-safe-A/21:failed|failed| ok |
[ 0.000000] sirq-safe-A => hirqs-on/12:failed|failed| ok |
[ 0.000000] sirq-safe-A => hirqs-on/21:failed|failed| ok |
[ 0.000000] hard-safe-A + irqs-on/12:failed|failed| ok |
[ 0.000000] soft-safe-A + irqs-on/12:failed|failed| ok |
[ 0.000000] hard-safe-A + irqs-on/21:failed|failed| ok |
[ 0.000000] soft-safe-A + irqs-on/21:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/123:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/123:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/132:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/132:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/213:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/213:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/231:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/231:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/312:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/312:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/321:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/321:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/123:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/123:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/132:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/132:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/213:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/213:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/231:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/231:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/312:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/312:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/321:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/321:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/123:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/123:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/132:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/132:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/213:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/213:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/231:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/231:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/312:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/312:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/321:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/321:failed|failed| ok |
[ 0.000000] hard-irq read-recursion/123: ok |
[ 0.000000] soft-irq read-recursion/123: ok |
[ 0.000000] hard-irq read-recursion/132: ok |
[ 0.000000] soft-irq read-recursion/132: ok |
[ 0.000000] hard-irq read-recursion/213: ok |
[ 0.000000] soft-irq read-recursion/213: ok |
[ 0.000000] hard-irq read-recursion/231: ok |
[ 0.000000] soft-irq read-recursion/231: ok |
[ 0.000000] hard-irq read-recursion/312: ok |
[ 0.000000] soft-irq read-recursion/312: ok |
[ 0.000000] hard-irq read-recursion/321: ok |
[ 0.000000] soft-irq read-recursion/321: ok |
[ 0.000000] --------------------------------------------------------------------------
[ 0.000000] | Wound/wait tests |
[ 0.000000] ---------------------
[ 0.000000] ww api failures: ok | ok | ok |
[ 0.000000] ww contexts mixing:failed| ok |
[ 0.000000] finishing ww context: ok | ok | ok | ok |
[ 0.000000] locking mismatches: ok | ok | ok |
[ 0.000000] EDEADLK handling: ok | ok | ok | ok | ok | ok | ok | ok | ok | ok |
[ 0.000000] spinlock nest unlocked: ok |
[ 0.000000] -----------------------------------------------------
[ 0.000000] |block | try |context|
[ 0.000000] -----------------------------------------------------
[ 0.000000] context:failed| ok | ok |
[ 0.000000] try:failed| ok |failed|
[ 0.000000] block:failed| ok |failed|
[ 0.000000] spinlock:failed| ok |failed|
[ 0.000000] --------------------------------------------------------
[ 0.000000] 141 out of 253 testcases failed, as expected. |
[ 0.000000] ----------------------------------------------------
[ 0.000000] ODEBUG: 15 of 15 active objects replaced
[ 0.000000] ODEBUG: selftest passed
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Detected 2693.508 MHz processor
[ 0.000000] tsc: Marking TSC unstable due to TSCs unsynchronized
[ 0.012000] Calibrating delay loop (skipped) preset value.. 5387.01 BogoMIPS (lpj=10774032)
[ 0.013636] pid_max: default: 4096 minimum: 301
[ 0.016073] Mount-cache hash table entries: 512
[ 0.018625] Initializing cgroup subsys debug
[ 0.020022] Initializing cgroup subsys devices
[ 0.024026] Initializing cgroup subsys freezer
[ 0.026092] Initializing cgroup subsys net_cls
[ 0.027192] Initializing cgroup subsys blkio
[ 0.028020] Initializing cgroup subsys perf_event
[ 0.032025] Initializing cgroup subsys net_prio
[ 0.034439] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.034439] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[ 0.034439] tlb_flushall_shift: -1
[ 0.040842] debug: unmapping init [mem 0x82219000-0x82221fff]
[ 0.050702] Getting VERSION: 50014
[ 0.052013] Getting VERSION: 50014
[ 0.053849] Getting ID: 0
[ 0.056027] Getting ID: f000000
[ 0.057861] Getting LVT0: 8700
[ 0.059501] Getting LVT1: 8400
[ 0.060020] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.064143] enabled ExtINT on CPU#0
[ 0.068055] ENABLING IO-APIC IRQs
[ 0.072027] init IO_APIC IRQs
[ 0.076015] apic 0 pin 0 not connected
[ 0.077991] IOAPIC[0]: Set routing entry (0-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:1)
[ 0.080058] IOAPIC[0]: Set routing entry (0-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:1)
[ 0.084056] IOAPIC[0]: Set routing entry (0-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:1)
[ 0.088052] IOAPIC[0]: Set routing entry (0-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:1)
[ 0.092051] IOAPIC[0]: Set routing entry (0-5 -> 0x35 -> IRQ 5 Mode:1 Active:0 Dest:1)
[ 0.096053] IOAPIC[0]: Set routing entry (0-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:1)
[ 0.100051] IOAPIC[0]: Set routing entry (0-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:1)
[ 0.104052] IOAPIC[0]: Set routing entry (0-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:1)
[ 0.108056] IOAPIC[0]: Set routing entry (0-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:1)
[ 0.112062] IOAPIC[0]: Set routing entry (0-10 -> 0x3a -> IRQ 10 Mode:1 Active:0 Dest:1)
[ 0.116051] IOAPIC[0]: Set routing entry (0-11 -> 0x3b -> IRQ 11 Mode:1 Active:0 Dest:1)
[ 0.120052] IOAPIC[0]: Set routing entry (0-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:1)
[ 0.124058] IOAPIC[0]: Set routing entry (0-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:1)
[ 0.128050] IOAPIC[0]: Set routing entry (0-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:1)
[ 0.132051] IOAPIC[0]: Set routing entry (0-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:1)
[ 0.136049] apic 0 pin 16 not connected
[ 0.140010] apic 0 pin 17 not connected
[ 0.141251] apic 0 pin 18 not connected
[ 0.144005] apic 0 pin 19 not connected
[ 0.145356] apic 0 pin 20 not connected
[ 0.147376] apic 0 pin 21 not connected
[ 0.148011] apic 0 pin 22 not connected
[ 0.150122] apic 0 pin 23 not connected
[ 0.152192] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.156010] smpboot: CPU0: GenuineIntel Common KVM processor (fam: 0f, model: 06, stepping: 01)
[ 0.161144] Using local APIC timer interrupts.
[ 0.161144] calibrating APIC timer ...
[ 0.168000] ... lapic delta = 6249564
[ 0.168000] ... PM-Timer delta = 357923
[ 0.168000] ... PM-Timer result ok
[ 0.168000] ..... delta 6249564
[ 0.168000] ..... mult: 268416729
[ 0.168000] ..... calibration result: 3999720
[ 0.168000] ..... CPU clock speed is 2693.0593 MHz.
[ 0.168000] ..... host bus clock speed is 999.3720 MHz.
[ 0.168131] Performance Events: no PMU driver, software events only.
[ 0.175541] CPU 1 irqstacks, hard=8f086000 soft=8f090000
[ 0.176012] x86: Booting SMP configuration:
[ 0.180010] .... node #0, CPUs: #1
[ 0.012000] Initializing CPU#1
[ 0.012000] kvm-clock: cpu 1, msr 0:fffb021, secondary cpu clock
[ 0.012000] masked ExtINT on CPU#1
[ 0.194698] x86: Booted up 1 node, 2 CPUs
[ 0.194633] KVM setup async PF for cpu 1
[ 0.194633] kvm-stealtime: cpu 1, msr f809540
[ 0.200028] ----------------
[ 0.201634] | NMI testsuite:
[ 0.204007] --------------------
[ 0.205970] remote IPI: ok |
[ 0.221224] local IPI: ok |
[ 0.244040] --------------------
[ 0.246770] Good, all 2 testcases passed! |
[ 0.248010] ---------------------------------
[ 0.250219] smpboot: Total of 2 processors activated (10774.03 BogoMIPS)
[ 0.252726] CPU0 attaching sched-domain:
[ 0.256057] domain 0: span 0-1 level CPU
[ 0.258166] groups: 0 1
[ 0.261022] CPU1 attaching sched-domain:
[ 0.263162] domain 0: span 0-1 level CPU
[ 0.265216] groups: 1 0
[ 0.268496] devtmpfs: initialized
[ 0.273590] xor: measuring software checksum speed
[ 0.316031] pIII_sse : 80.000 MB/sec
[ 0.356063] prefetch64-sse: 81.000 MB/sec
[ 0.358520] xor: using function: prefetch64-sse (81.000 MB/sec)
[ 0.360043] atomic64 test passed for i386+ platform with CX8 and with SSE
[ 0.364500] regulator-dummy: no parameters
[ 0.367128] NET: Registered protocol family 16
[ 0.369279] cpuidle: using governor ladder
[ 0.372013] cpuidle: using governor menu
[ 0.376089] ACPI: bus type PCI registered
[ 0.378420] PCI: PCI BIOS revision 2.10 entry at 0xfd4e3, last bus=0
[ 0.380011] PCI: Using configuration type 1 for base access
[ 0.398117] bio: create slab <bio-0> at 0
[ 0.468047] raid6: mmxx1 1965 MB/s
[ 0.536030] raid6: mmxx2 2066 MB/s
[ 0.604038] raid6: sse1x1 1687 MB/s
[ 0.672026] raid6: sse1x2 1995 MB/s
[ 0.740032] raid6: sse2x1 3289 MB/s
[ 0.808027] raid6: sse2x2 4043 MB/s
[ 0.810189] raid6: using algorithm sse2x2 (4043 MB/s)
[ 0.812012] raid6: using intx1 recovery algorithm
[ 0.816007] ACPI: Added _OSI(Module Device)
[ 0.818260] ACPI: Added _OSI(Processor Device)
[ 0.820012] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.822397] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.840253] ACPI: Interpreter enabled
[ 0.842482] ACPI: (supports S0 S5)
[ 0.844010] ACPI: Using IOAPIC for interrupt routing
[ 0.846458] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.869792] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.872024] acpi PNP0A03:00: _OSC: OS supports [Segments]
[ 0.874609] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.876407] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[ 0.884192] PCI host bridge to bus 0000:00
[ 0.886239] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.888015] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.890864] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.892015] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.896021] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff]
[ 0.900125] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000
[ 0.905121] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100
[ 0.909252] pci 0000:00:01.1: [8086:7010] type 00 class 0x010180
[ 0.917610] pci 0000:00:01.1: reg 0x20: [io 0xc060-0xc06f]
[ 0.922746] pci 0000:00:01.3: [8086:7113] type 00 class 0x068000
[ 0.924717] pci 0000:00:01.3: quirk: [io 0xb000-0xb03f] claimed by PIIX4 ACPI
[ 0.928036] pci 0000:00:01.3: quirk: [io 0xb100-0xb10f] claimed by PIIX4 SMB
[ 0.932753] pci 0000:00:02.0: [1013:00b8] type 00 class 0x030000
[ 0.944074] pci 0000:00:02.0: reg 0x10: [mem 0xfc000000-0xfdffffff pref]
[ 0.952081] pci 0000:00:02.0: reg 0x14: [mem 0xfebe2000-0xfebe2fff]
[ 0.976051] pci 0000:00:02.0: reg 0x30: [mem 0xfebd0000-0xfebdffff pref]
[ 0.977983] pci 0000:00:03.0: [1af4:1000] type 00 class 0x020000
[ 0.980010] pci 0000:00:03.0: reg 0x10: [io 0xc040-0xc05f]
[ 0.982040] pci 0000:00:03.0: reg 0x14: [mem 0xfebe1000-0xfebe1fff]
[ 0.987517] pci 0000:00:03.0: reg 0x30: [mem 0xfebc0000-0xfebcffff pref]
[ 0.988360] pci 0000:00:04.0: [8086:100e] type 00 class 0x020000
[ 0.990476] pci 0000:00:04.0: reg 0x10: [mem 0xfeb80000-0xfeb9ffff]
[ 0.992901] pci 0000:00:04.0: reg 0x14: [io 0xc000-0xc03f]
[ 0.999129] pci 0000:00:04.0: reg 0x30: [mem 0xfeba0000-0xfebbffff pref]
[ 1.000317] pci 0000:00:05.0: [8086:25ab] type 00 class 0x088000
[ 1.001999] pci 0000:00:05.0: reg 0x10: [mem 0xfebe0000-0xfebe000f]
[ 1.007026] pci_bus 0000:00: on NUMA node 0
[ 1.008667] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11)
[ 1.010267] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 *10 11)
[ 1.011811] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 10 *11)
[ 1.012787] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 10 *11)
[ 1.014350] ACPI: PCI Interrupt Link [LNKS] (IRQs *9)
[ 1.016917] ACPI: Enabled 16 GPEs in block 00 to 0F
[ 1.018836] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.018836] vgaarb: loaded
[ 1.018836] vgaarb: bridge control possible 0000:00:02.0
[ 1.020128] SCSI subsystem initialized
[ 1.023305] libata version 3.00 loaded.
[ 1.023305] ACPI: bus type USB registered
[ 1.023305] usbcore: registered new interface driver usbfs
[ 1.024033] usbcore: registered new interface driver hub
[ 1.027774] usbcore: registered new device driver usb
[ 1.027774] pps_core: LinuxPPS API ver. 1 registered
[ 1.027774] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.028016] PTP clock support registered
[ 1.028890] PCI: Using ACPI for IRQ routing
[ 1.029759] PCI: pci_cache_line_size set to 64 bytes
[ 1.032137] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 1.033280] e820: reserve RAM buffer [mem 0x0fffe000-0x0fffffff]
[ 1.034824] irda_init()
[ 1.035534] NET: Registered protocol family 23
[ 1.036045] Bluetooth: Core ver 2.18
[ 1.036880] NET: Registered protocol family 31
[ 1.037779] Bluetooth: HCI device and connection manager initialized
[ 1.039007] Bluetooth: HCI socket layer initialized
[ 1.040016] Bluetooth: L2CAP socket layer initialized
[ 1.041048] Bluetooth: SCO socket layer initialized
[ 1.045382] cfg80211: Calling CRDA to update world regulatory domain
[ 1.045880] Switched to clocksource kvm-clock
[ 1.045880] FS-Cache: Loaded
[ 1.045922] CacheFiles: Loaded
[ 1.046692] pnp: PnP ACPI init
[ 1.047411] ACPI: bus type PNP registered
[ 1.048352] IOAPIC[0]: Set routing entry (0-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:3)
[ 1.052070] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.053394] IOAPIC[0]: Set routing entry (0-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:3)
[ 1.055167] pnp 00:01: Plug and Play ACPI device, IDs PNP0303 (active)
[ 1.056469] IOAPIC[0]: Set routing entry (0-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:3)
[ 1.058199] pnp 00:02: Plug and Play ACPI device, IDs PNP0f13 (active)
[ 1.059495] IOAPIC[0]: Set routing entry (0-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:3)
[ 1.061148] pnp 00:03: [dma 2]
[ 1.061904] pnp 00:03: Plug and Play ACPI device, IDs PNP0700 (active)
[ 1.063274] IOAPIC[0]: Set routing entry (0-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:3)
[ 1.064966] pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active)
[ 1.066283] IOAPIC[0]: Set routing entry (0-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:3)
[ 1.067967] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.069639] pnp 00:06: Plug and Play ACPI device, IDs PNP0103 (active)
[ 1.071121] pnp: PnP ACPI: found 7 devices
[ 1.071983] ACPI: bus type PNP unregistered
[ 1.111354] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 1.112559] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 1.113656] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.114884] pci_bus 0000:00: resource 7 [mem 0x80000000-0xfebfffff]
[ 1.116195] NET: Registered protocol family 2
[ 1.117686] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.119092] TCP bind hash table entries: 2048 (order: 4, 90112 bytes)
[ 1.120476] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.121754] TCP: reno registered
[ 1.122500] UDP hash table entries: 128 (order: 1, 12288 bytes)
[ 1.123682] UDP-Lite hash table entries: 128 (order: 1, 12288 bytes)
[ 1.125161] NET: Registered protocol family 1
[ 1.126115] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[ 1.127294] pci 0000:00:01.0: PIIX3: Enabling Passive Release
[ 1.128456] pci 0000:00:01.0: Activating ISA DMA hang workarounds
[ 1.129674] pci 0000:00:02.0: Boot video device
[ 1.130662] PCI: CLS 0 bytes, default 64
[ 1.394320] Unpacking initramfs...
[ 2.121341] debug: unmapping init [mem 0x8fce6000-0x8ffeffff]
[ 2.125846] cryptomgr_test (25) used greatest stack depth: 7220 bytes left
[ 2.129704] PCLMULQDQ-NI instructions are not detected.
[ 2.131872] The force parameter has not been set to 1. The Iris poweroff handler will not be installed.
[ 2.135487] NatSemi SCx200 Driver
[ 2.137615] futex hash table entries: 16 (order: -3, 768 bytes)
[ 2.139370] Initialise system trusted keyring
[ 2.141665] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 2.150850] VFS: Disk quotas dquot_6.5.2
[ 2.152523] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.155316] DLM installed
[ 2.158305] NTFS driver 2.1.30 [Flags: R/O DEBUG].
[ 2.160836] ocfs2 stack glue: unable to register sysctl
[ 2.162356] ocfs2: Registered cluster interface o2cb
[ 2.164094] OCFS2 User DLM kernel interface loaded
[ 2.169919] msgmni has been set to 446
[ 2.182029] Key type asymmetric registered
[ 2.183519] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 2.186111] io scheduler noop registered (default)
[ 2.187523] io scheduler deadline registered
[ 2.188826] io scheduler cfq registered
[ 2.190023] list_sort_test: start testing list_sort()
[ 2.191782] test_string_helpers: Running tests...
[ 2.194328] no IO addresses supplied
[ 2.195696] usbcore: registered new interface driver udlfb
[ 2.197237] usbcore: registered new interface driver smscufx
[ 2.200202] kworker/u4:0 (85) used greatest stack depth: 6880 bytes left
[ 2.202082] uvesafb: failed to execute /sbin/v86d
[ 2.203435] uvesafb: make sure that the v86d helper is installed and executable
[ 2.205558] uvesafb: Getting VBE info block failed (eax=0x4f00, err=-8)
[ 2.207235] uvesafb: vbe_init() failed with -22
[ 2.208528] uvesafb: probe of uvesafb.0 failed with error -22
[ 2.210566] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 2.212682] ACPI: Power Button [PWRF]
[ 2.214976] r3964: Philips r3964 Driver $Revision: 1.10 $
[ 2.216512] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.251476] 00:05: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 2.255246] STMicroelectronics ASC driver initialized
[ 2.256935] serial: Freescale lpuart driver
[ 2.258576] lp: driver loaded but no devices found
[ 2.259893] toshiba: not a supported Toshiba laptop
[ 2.261701] ppdev: user-space parallel port driver
[ 2.263144] scx200_gpio: no SCx200 gpio present
[ 2.264529] platform pc8736x_gpio.0: NatSemi pc8736x GPIO Driver Initializing
[ 2.266339] platform pc8736x_gpio.0: no device found
[ 2.267795] nsc_gpio initializing
[ 2.268886] telclk_interrupt = 0xf non-mcpbl0010 hw.
[ 2.270325] SyncLink PC Card driver $Revision: 4.34 $, tty major#245
[ 2.272098] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
[ 2.275218] Hangcheck: Using getrawmonotonic().
[ 2.277478] parport_pc 00:04: reported by Plug and Play ACPI
[ 2.279942] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 2.380662] lp0: using parport0 (interrupt-driven).
[ 2.385885] Floppy drive(s): fd0 is 1.44M
[ 2.394564] loop: module loaded
[ 2.396533] rbd: loaded
[ 2.397807] blk-mq: CPU -> queue map
[ 2.399544] CPU 0 -> Queue 0
[ 2.401016] CPU 1 -> Queue 0
[ 2.404207] nullb0: unknown partition table
[ 2.406830] FDC 0 is a S82078B
[ 2.406892] blk-mq: CPU -> queue map
[ 2.406893] CPU 0 -> Queue 0
[ 2.406893] CPU 1 -> Queue 0
[ 2.416684] nullb1: unknown partition table
[ 2.419346] null: module loaded
[ 2.422351] zram: Created 1 device(s) ...
[ 2.424592] dummy-irq: no IRQ given. Use irq=N
[ 2.426915] lkdtm: No crash points registered, enable through debugfs
[ 2.429963] Silicon Labs C2 port support v. 0.51.0 - (C) 2007 Rodolfo Giometti
[ 2.433768] c2port c2port0: C2 port uc added
[ 2.434689] c2port c2port0: uc flash has 30 blocks x 512 bytes (15360 bytes total)
[ 2.436654] usbcore: registered new interface driver viperboard
[ 2.437819] Uniform Multi-Platform E-IDE driver
[ 2.438846] piix 0000:00:01.1: IDE controller (0x8086:0x7010 rev 0x00)
[ 2.440185] piix 0000:00:01.1: not 100% native mode: will probe irqs later
[ 2.442135] ide0: BM-DMA at 0xc060-0xc067
[ 2.443081] ide1: BM-DMA at 0xc068-0xc06f
[ 2.443995] Probing IDE interface ide0...
[ 3.014829] Probing IDE interface ide1...
[ 3.754810] hdc: QEMU DVD-ROM, ATAPI CD/DVD-ROM drive
[ 4.430638] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO0
[ 4.433191] hdc: MWDMA2 mode selected
[ 4.435029] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 4.436943] ide1 at 0x170-0x177,0x376 on irq 15
[ 4.439489] ide-gd driver 1.18
[ 4.442813] Loading iSCSI transport class v2.0-870.
[ 4.445442] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[ 4.448054] osd: LOADED open-osd 0.2.1
[ 4.450716] Rounding down aligned max_sectors from 4294967295 to 4294967288
[ 4.457102] SSFDC read-only Flash Translation layer
[ 4.459309] L440GX flash mapping: failed to find PIIX4 ISA bridge, cannot continue
[ 4.462749] Failed to ioremap_nocache
[ 4.464596] slram: not enough parameters.
[ 4.906125] parport0: AVR Butterfly
[ 4.907163] parport0: cannot grant exclusive access for device spi-lm70llp
[ 4.909417] spi-lm70llp: spi_lm70llp probe fail, status -12
[ 4.911397] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 4.915972] eql: Equalizer2002: Simon Janes (simon@ncm.com) and David S. Miller (davem@redhat.com)
[ 4.920305] tun: Universal TUN/TAP device driver, 1.6
[ 4.921734] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 4.923337] arcnet loaded.
[ 4.924402] arcnet: RFC1201 "standard" (`a') encapsulation support loaded.
[ 4.926088] arcnet: RFC1051 "simple standard" (`s') encapsulation support loaded.
[ 4.928127] arcnet: raw mode (`r') encapsulation support loaded.
[ 4.929633] arcnet: cap mode (`c') encapsulation support loaded.
[ 4.932002] arcnet: COM90xx chipset support
[ 5.232765] S3: No ARCnet cards found.
[ 5.234689] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[ 5.240676] ipddp0: Appletalk-IP Decap. mode by Jay Schulist <jschlst@samba.org>
[ 5.246552] slcan: serial line CAN interface driver
[ 5.249749] slcan: 10 dynamic interface channels.
[ 5.252643] CAN device driver interface
[ 5.255390] usbcore: registered new interface driver ems_usb
[ 5.259066] usbcore: registered new interface driver esd_usb2
[ 5.262792] usbcore: registered new interface driver kvaser_usb
[ 5.265219] usbcore: registered new interface driver peak_usb
[ 5.267167] usbcore: registered new interface driver usb_8dev
[ 5.269293] sja1000 CAN netdevice driver
[ 5.270972] sja1000_isa: insufficient parameters supplied
[ 5.273252] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
[ 5.276288] usbcore: registered new interface driver irda-usb
[ 5.277511] usbcore: registered new interface driver stir4200
[ 5.280800] usbcore: registered new interface driver mcs7780
[ 5.283335] usbcore: registered new interface driver kingsun-sir
[ 5.285676] usbcore: registered new interface driver ks959-sir
[ 5.288501] NET3 PLIP version 2.4-parport gniibe@mri.co.jp
[ 5.290542] plip0: Parallel port at 0x378, using IRQ 7.
[ 5.291593] PPP generic driver version 2.4.2
[ 5.296975] PPP BSD Compression module registered
[ 5.300164] PPP Deflate Compression module registered
[ 5.303224] PPP MPPE Compression module registered
[ 5.306205] NET: Registered protocol family 24
[ 5.308995] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
[ 5.313166] usbcore: registered new interface driver kaweth
[ 5.316540] usbcore: registered new interface driver r8152
[ 5.320037] usbcore: registered new interface driver cdc_phonet
[ 5.323755] parport0: cannot grant exclusive access for device ks0108
[ 5.327584] ks0108: ERROR: parport didn't register new device
[ 5.331152] cfag12864b: ERROR: ks0108 is not initialized
[ 5.334459] cfag12864bfb: ERROR: cfag12864b is not initialized
[ 5.339533] aoe: AoE v85 initialised.
[ 5.342520] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.346214] ehci-pci: EHCI PCI platform driver
[ 5.347716] ehci-platform: EHCI generic platform driver
[ 5.349075] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.350900] ohci-pci: OHCI PCI platform driver
[ 5.353029] ohci-platform: OHCI generic platform driver
[ 5.355099] driver u132_hcd
[ 5.357145] fusbh200_hcd: FUSBH200 Host Controller (EHCI) Driver
[ 5.359564] Warning! fusbh200_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 5.363410] fotg210_hcd: FOTG210 Host Controller (EHCI) Driver
[ 5.365693] 4Warning! fotg210_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 5.369581] usbcore: registered new interface driver cdc_acm
[ 5.371952] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 5.375634] usbcore: registered new interface driver usblp
[ 5.377852] usbcore: registered new interface driver cdc_wdm
[ 5.380088] usbcore: registered new interface driver usbtmc
[ 5.382352] usbcore: registered new interface driver usb-storage
[ 5.384782] usbcore: registered new interface driver ums-alauda
[ 5.387245] usbcore: registered new interface driver ums-cypress
[ 5.389692] usbcore: registered new interface driver ums_eneub6250
[ 5.392264] usbcore: registered new interface driver ums-jumpshot
[ 5.394635] usbcore: registered new interface driver ums-sddr09
[ 5.397059] usbcore: registered new interface driver ums-usbat
[ 5.399614] usbcore: registered new interface driver mdc800
[ 5.401878] mdc800: v0.7.5 (30/10/2000):USB Driver for Mustek MDC800 Digital Camera
[ 5.405158] usbcore: registered new interface driver microtekX6
[ 5.407749] usbcore: registered new interface driver usbserial
[ 5.410134] usbcore: registered new interface driver usbserial_generic
[ 5.412897] usbserial: USB Serial support registered for generic
[ 5.415366] usbcore: registered new interface driver aircable
[ 5.417740] usbserial: USB Serial support registered for aircable
[ 5.420268] usbcore: registered new interface driver ark3116
[ 5.422530] usbserial: USB Serial support registered for ark3116
[ 5.424829] usbcore: registered new interface driver belkin_sa
[ 5.426614] usbserial: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
[ 5.428789] usbcore: registered new interface driver ch341
[ 5.430064] usbserial: USB Serial support registered for ch341-uart
[ 5.431426] usbcore: registered new interface driver cp210x
[ 5.433194] usbserial: USB Serial support registered for cp210x
[ 5.435513] usbcore: registered new interface driver cyberjack
[ 5.437994] usbserial: USB Serial support registered for Reiner SCT Cyberjack USB card reader
[ 5.440011] usbcore: registered new interface driver cypress_m8
[ 5.441325] usbserial: USB Serial support registered for DeLorme Earthmate USB
[ 5.443087] usbserial: USB Serial support registered for HID->COM RS232 Adapter
[ 5.444804] usbserial: USB Serial support registered for Nokia CA-42 V2 Adapter
[ 5.446973] usbcore: registered new interface driver usb_debug
[ 5.449135] usbserial: USB Serial support registered for debug
[ 5.451307] usbcore: registered new interface driver digi_acceleport
[ 5.453731] usbserial: USB Serial support registered for Digi 2 port USB adapter
[ 5.457042] usbserial: USB Serial support registered for Digi 4 port USB adapter
[ 5.460292] usbcore: registered new interface driver empeg
[ 5.462564] usbserial: USB Serial support registered for empeg
[ 5.464956] usbcore: registered new interface driver ftdi_sio
[ 5.467232] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 5.470562] usbcore: registered new interface driver ipw
[ 5.472728] usbserial: USB Serial support registered for IPWireless converter
[ 5.474856] usbcore: registered new interface driver keyspan
[ 5.476179] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 5.478090] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 5.479899] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 5.481712] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 5.483500] usbcore: registered new interface driver metro_usb
[ 5.484803] usbserial: USB Serial support registered for Metrologic USB to Serial
[ 5.486662] usbcore: registered new interface driver mos7840
[ 5.487949] usbserial: USB Serial support registered for Moschip 7840/7820 USB Serial Driver
[ 5.489879] usbcore: registered new interface driver mxuport
[ 5.491173] usbserial: USB Serial support registered for MOXA UPort
[ 5.492561] usbcore: registered new interface driver navman
[ 5.493801] usbserial: USB Serial support registered for navman
[ 5.495116] usbcore: registered new interface driver omninet
[ 5.496369] usbserial: USB Serial support registered for ZyXEL - omni.net lcd plus usb
[ 5.498570] usbcore: registered new interface driver opticon
[ 5.500779] usbserial: USB Serial support registered for opticon
[ 5.502506] usbcore: registered new interface driver option
[ 5.503912] usbserial: USB Serial support registered for GSM modem (1-port)
[ 5.505452] usbcore: registered new interface driver qcaux
[ 5.507468] usbserial: USB Serial support registered for qcaux
[ 5.509929] usbcore: registered new interface driver qcserial
[ 5.512443] usbserial: USB Serial support registered for Qualcomm USB modem
[ 5.514449] usbcore: registered new interface driver usb_serial_simple
[ 5.516240] usbserial: USB Serial support registered for zio
[ 5.517802] usbserial: USB Serial support registered for funsoft
[ 5.519619] usbserial: USB Serial support registered for flashloader
[ 5.521306] usbserial: USB Serial support registered for vivopay
[ 5.523109] usbserial: USB Serial support registered for moto_modem
[ 5.525264] usbserial: USB Serial support registered for hp4x
[ 5.527149] usbserial: USB Serial support registered for suunto
[ 5.529498] usbserial: USB Serial support registered for siemens_mpi
[ 5.532117] usbcore: registered new interface driver spcp8x5
[ 5.534420] usbserial: USB Serial support registered for SPCP8x5
[ 5.536351] usbcore: registered new interface driver ssu100
[ 5.537986] usbserial: USB Serial support registered for Quatech SSU-100 USB to Serial Driver
[ 5.540925] usbcore: registered new interface driver visor
[ 5.543067] usbserial: USB Serial support registered for Handspring Visor / Palm OS
[ 5.545340] usbserial: USB Serial support registered for Sony Clie 5.0
[ 5.547699] usbserial: USB Serial support registered for Sony Clie 3.5
[ 5.549788] usbcore: registered new interface driver wishbone_serial
[ 5.551876] usbserial: USB Serial support registered for wishbone_serial
[ 5.554628] usbcore: registered new interface driver whiteheat
[ 5.556995] usbserial: USB Serial support registered for Connect Tech - WhiteHEAT - (prerenumeration)
[ 5.560938] usbserial: USB Serial support registered for Connect Tech - WhiteHEAT
[ 5.564523] usbcore: registered new interface driver xsens_mt
[ 5.567181] usbserial: USB Serial support registered for xsens_mt
[ 5.569405] usbcore: registered new interface driver zte_ev
[ 5.571699] usbserial: USB Serial support registered for zte_ev
[ 5.573991] usbcore: registered new interface driver appledisplay
[ 5.575981] usbcore: registered new interface driver cytherm
[ 5.577659] usbcore: registered new interface driver emi26 - firmware loader
[ 5.579584] usbcore: registered new interface driver emi62 - firmware loader
[ 5.581481] driver ftdi-elan
[ 5.583383] usbcore: registered new interface driver ftdi-elan
[ 5.585884] usbcore: registered new interface driver idmouse
[ 5.588206] usbcore: registered new interface driver iowarrior
[ 5.590530] usbcore: registered new interface driver usblcd
[ 5.592846] usbcore: registered new interface driver usbled
[ 5.594757] usbcore: registered new interface driver legousbtower
[ 5.596779] usbcore: registered new interface driver rio500
[ 5.598642] usbcore: registered new interface driver uss720
[ 5.600724] uss720: v0.6:USB Parport Cable driver for Cables using the Lucent Technologies USS720 Chip
[ 5.604944] uss720: NOTE: this is a special purpose driver to allow nonstandard
[ 5.608317] uss720: protocols (eg. bitbang) over USS720 usb to parallel cables
[ 5.611701] uss720: If you just want to connect to a printer, use usblp instead
[ 5.615286] usbcore: registered new interface driver sisusb
[ 5.618182] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 5.623134] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 5.625099] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 5.703450] evbug: Connected device: input0 (Power Button at LNXPWRBN/button/input0)
[ 5.708145] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 5.711311] evbug: Connected device: input1 (AT Translated Set 2 keyboard at isa0060/serio0/input0)
[ 5.715087] usbcore: registered new interface driver appletouch
[ 5.718162] usbcore: registered new interface driver xpad
[ 5.721308] mk712: device not present
[ 5.723587] usbcore: registered new interface driver usbtouchscreen
[ 5.726224] apanel: Fujitsu BIOS signature 'FJKEYINF' not found...
[ 5.728816] usbcore: registered new interface driver ati_remote2
[ 5.730929] cm109: Keymap for Komunikate KIP1000 phone loaded
[ 5.736132] usbcore: registered new interface driver cm109
[ 5.738453] cm109: CM109 phone driver: 20080805 (C) Alfred E. Heggestad
[ 5.740955] usbcore: registered new interface driver keyspan_remote
[ 5.743527] usbcore: registered new interface driver powermate
[ 5.745568] wistron_btns: System unknown
[ 5.747163] i2c /dev entries driver
[ 5.748987] i2c-parport: adapter type unspecified
[ 5.750927] i2c-parport-light: adapter type unspecified
[ 5.753095] usbcore: registered new interface driver i2c-tiny-usb
[ 5.755289] scx200_i2c: no SCx200 gpio pins available
[ 5.757526] pps_ldisc: PPS line discipline registered
[ 5.759623] pps_parport: parallel port PPS client
[ 5.761589] parport0: cannot grant exclusive access for device pps_parport
[ 5.764038] pps_parport: couldn't register with parport0
[ 5.765984] Driver for 1-wire Dallas network protocol.
[ 5.767755] usbcore: registered new interface driver DS9490R
[ 5.769971] DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
[ 5.772499] 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
[ 5.776441] power_supply test_ac: uevent
[ 5.778205] power_supply test_ac: POWER_SUPPLY_NAME=test_ac
[ 5.780950] power_supply test_ac: prop ONLINE=1
[ 5.782617] power_supply test_ac: power_supply_changed
[ 5.786358] power_supply test_ac: power_supply_changed_work
[ 5.790239] power_supply test_ac: power_supply_update_gen_leds 1
[ 5.794494] power_supply test_ac: uevent
[ 5.796114] power_supply test_battery: uevent
[ 5.796117] power_supply test_battery: POWER_SUPPLY_NAME=test_battery
[ 5.796139] power_supply test_battery: prop STATUS=Discharging
[ 5.796144] power_supply test_battery: prop CHARGE_TYPE=Fast
[ 5.796148] power_supply test_battery: prop HEALTH=Good
[ 5.796153] power_supply test_battery: prop PRESENT=1
[ 5.796157] power_supply test_battery: prop TECHNOLOGY=Li-ion
[ 5.796162] power_supply test_battery: prop CHARGE_FULL_DESIGN=100
[ 5.796165] power_supply test_battery: prop CHARGE_FULL=100
[ 5.796169] power_supply test_battery: prop CHARGE_NOW=50
[ 5.796172] power_supply test_battery: prop CAPACITY=50
[ 5.796176] power_supply test_battery: prop CAPACITY_LEVEL=Normal
[ 5.796179] power_supply test_battery: prop TIME_TO_EMPTY_AVG=3600
[ 5.796182] power_supply test_battery: prop TIME_TO_FULL_NOW=3600
[ 5.796186] power_supply test_battery: prop MODEL_NAME=Test battery
[ 5.796190] power_supply test_battery: prop MANUFACTURER=Linux
[ 5.796193] power_supply test_battery: prop SERIAL_NUMBER=3.14.0-rc5-00009-g4dea8e4
[ 5.796197] power_supply test_battery: prop TEMP=26
[ 5.796200] power_supply test_battery: prop VOLTAGE_NOW=3300
[ 5.796497] power_supply test_battery: power_supply_changed
[ 5.796536] power_supply test_battery: power_supply_changed_work
[ 5.796545] power_supply test_battery: power_supply_update_bat_leds 2
[ 5.796556] power_supply test_battery: uevent
[ 5.796558] power_supply test_battery: POWER_SUPPLY_NAME=test_battery
[ 5.796568] power_supply test_battery: prop STATUS=Discharging
[ 5.796572] power_supply test_battery: prop CHARGE_TYPE=Fast
[ 5.796575] power_supply test_battery: prop HEALTH=Good
[ 5.796578] power_supply test_battery: prop PRESENT=1
[ 5.796588] power_supply test_battery: prop TECHNOLOGY=Li-ion
[ 5.796593] power_supply test_battery: prop CHARGE_FULL_DESIGN=100
[ 5.796596] power_supply test_battery: prop CHARGE_FULL=100
[ 5.796600] power_supply test_battery: prop CHARGE_NOW=50
[ 5.796603] power_supply test_battery: prop CAPACITY=50
[ 5.796607] power_supply test_battery: prop CAPACITY_LEVEL=Normal
[ 5.796610] power_supply test_battery: prop TIME_TO_EMPTY_AVG=3600
[ 5.796613] power_supply test_battery: prop TIME_TO_FULL_NOW=3600
[ 5.796617] power_supply test_battery: prop MODEL_NAME=Test battery
[ 5.796620] power_supply test_battery: prop MANUFACTURER=Linux
[ 5.796624] power_supply test_battery: prop SERIAL_NUMBER=3.14.0-rc5-00009-g4dea8e4
[ 5.796627] power_supply test_battery: prop TEMP=26
[ 5.796630] power_supply test_battery: prop VOLTAGE_NOW=3300
[ 5.796695] power_supply test_usb: uevent
[ 5.796697] power_supply test_usb: POWER_SUPPLY_NAME=test_usb
[ 5.796705] power_supply test_usb: prop ONLINE=1
[ 5.796722] power_supply test_usb: power_supply_changed
[ 5.796771] power_supply test_usb: power_supply_changed_work
[ 5.796775] power_supply test_usb: power_supply_update_gen_leds 1
[ 5.796778] power_supply test_usb: uevent
[ 5.796779] power_supply test_usb: POWER_SUPPLY_NAME=test_usb
[ 5.796782] power_supply test_usb: prop ONLINE=1
[ 5.799998] pc87360: PC8736x not detected, module not inserted
[ 5.801087] Bluetooth: Virtual HCI driver ver 1.4
[ 5.801262] Bluetooth: HCI UART driver ver 2.2
[ 5.801275] Bluetooth: HCI H4 protocol initialized
[ 5.801280] Bluetooth: HCI Three-wire UART (H5) protocol initialized
[ 5.801335] usbcore: registered new interface driver bcm203x
[ 5.801377] usbcore: registered new interface driver bpa10x
[ 5.801412] usbcore: registered new interface driver bfusb
[ 5.807328] ISDN subsystem Rev: 1.1.2.3/1.1.2.2/none/1.1.2.2/1.1.2.2
[ 5.807778] CAPI 2.0 started up with major 68 (middleware)
[ 5.807880] dss1_divert module successfully installed
[ 5.807881] gigaset: Driver for Gigaset 307x (debug build)
[ 5.807890] gigaset: Kernel CAPI interface
[ 5.808005] usbcore: registered new interface driver usb_gigaset
[ 5.808006] usb_gigaset: USB Driver for Gigaset 307x using M105
[ 5.809658] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 5.811605] usbcore: registered new interface driver usbhid
[ 5.811611] usbhid: USB HID core driver
[ 5.811987] oprofile: using timer interrupt.
[ 5.812150] NET: Registered protocol family 26
[ 5.812202] netem: version 1.3
[ 5.812207] u32 classifier
[ 5.812210] Performance counters on
[ 5.812210] input device check on
[ 5.812238] Netfilter messages via NETLINK v0.30.
[ 5.812248] nfnl_acct: registering with nfnetlink.
[ 5.812392] nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net>
[ 5.812402] nf_tables_compat: (c) 2012 Pablo Neira Ayuso <pablo@netfilter.org>
[ 5.812561] xt_time: kernel timezone is -0000
[ 5.812595] ip_set: protocol 6
[ 5.812627] IPVS: Registered protocols (TCP, UDP, SCTP, AH)
[ 5.812687] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[ 5.812693] IPVS: Each connection entry needs 256 bytes at least
[ 5.812786] IPVS: Creating netns size=1356 id=0
[ 6.005108] power_supply test_ac: POWER_SUPPLY_NAME=test_ac
[ 6.008163] power_supply test_ac: prop ONLINE=1
[ 6.011074] IPVS: ipvs loaded.
[ 6.012603] IPVS: [rr] scheduler registered.
[ 6.014503] IPVS: [wrr] scheduler registered.
[ 6.016621] IPVS: [lc] scheduler registered.
[ 6.018488] IPVS: [wlc] scheduler registered.
[ 6.020075] IPVS: [lblc] scheduler registered.
[ 6.022164] IPVS: [lblcr] scheduler registered.
[ 6.024134] IPVS: [dh] scheduler registered.
[ 6.026052] IPVS: [nq] scheduler registered.
[ 6.028136] ipip: IPv4 over IPv4 tunneling driver
[ 6.030867] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 6.033853] arp_tables: (C) 2002 David S. Miller
[ 6.036397] TCP: cubic registered
[ 6.038084] NET: Registered protocol family 17
[ 6.040077] NET: Registered protocol family 15
[ 6.042096] NET: Registered protocol family 5
[ 6.043985] NET: Registered protocol family 9
[ 6.045989] X25: Linux Version 0.2
[ 6.047649] can: controller area network core (rev 20120528 abi 9)
[ 6.050334] NET: Registered protocol family 29
[ 6.052500] can: raw protocol (rev 20120528)
[ 6.054408] can: netlink gateway (rev 20130117) max_hops=1
[ 6.058449] IrCOMM protocol (Dag Brattli)
[ 6.065925] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 6.068232] Bluetooth: BNEP filters: protocol
[ 6.069728] Bluetooth: BNEP socket layer initialized
[ 6.071951] Bluetooth: CMTP (CAPI Emulation) ver 1.0
[ 6.074195] Bluetooth: CMTP socket layer initialized
[ 6.076351] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 6.078755] Bluetooth: HIDP socket layer initialized
[ 6.080478] NET: Registered protocol family 33
[ 6.082540] Key type rxrpc registered
[ 6.084298] Key type rxrpc_s registered
[ 6.086616] cryptomgr_probe (111) used greatest stack depth: 6812 bytes left
[ 6.086663] RxRPC: Registered security type 2 'rxkad'
[ 6.086692] l2tp_core: L2TP core driver, V2.0
[ 6.086702] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 6.086729] l2tp_debugfs: L2TP debugfs support
[ 6.086730] NET4: DECnet for Linux: V.2.5.68s (C) 1995-2003 Linux DECnet Project Team
[ 6.086881] DECnet: Routing cache hash table of 256 buckets, 11Kbytes
[ 6.086929] NET: Registered protocol family 12
[ 6.086974] NET: Registered protocol family 35
[ 6.087056] 8021q: 802.1Q VLAN Support v1.8
[ 6.087602] DCCP: Activated CCID 2 (TCP-like)
[ 6.087614] DCCP: Activated CCID 3 (TCP-Friendly Rate Control)
[ 6.088050] sctp: Hash tables configured (established 1365 bind 1489)
[ 6.088218] tipc: Activated (version 2.0.0)
[ 6.089064] NET: Registered protocol family 30
[ 6.089312] tipc: Started in single node mode
[ 6.089420] NET: Registered protocol family 37
[ 6.089432] Key type dns_resolver registered
[ 6.089451] Key type ceph registered
[ 6.089620] libceph: loaded (mon/osd proto 15/24)
[ 6.089834] batman_adv: B.A.T.M.A.N. advanced 2014.1.0 (compatibility version 15) loaded
[ 6.089835] openvswitch: Open vSwitch switching datapath
[ 6.089964] mpls_gso: MPLS GSO support
[ 6.090331]
[ 6.090331] printing PIC contents
[ 6.090341] ... PIC IMR: ffff
[ 6.090345] ... PIC IRR: 1053
[ 6.090353] ... PIC ISR: 0000
[ 6.090357] ... PIC ELCR: 0c00
[ 6.090367] printing local APIC contents on CPU#0/0:
[ 6.090374] ... APIC ID: 00000000 (0)
[ 6.090378] ... APIC VERSION: 00050014
[ 6.090382] ... APIC TASKPRI: 00000000 (00)
[ 6.090385] ... APIC PROCPRI: 00000000
[ 6.090387] ... APIC LDR: 01000000
[ 6.090390] ... APIC DFR: ffffffff
[ 6.090392] ... APIC SPIV: 000001ff
[ 6.090393] ... APIC ISR field:
[ 6.090412] 0000000000000000000000000000000000000000000000000000000000000000
[ 6.090413] ... APIC TMR field:
[ 6.090431] 0000000000000000000000000000000000000000000000000000000000000000
[ 6.090431] ... APIC IRR field:
[ 6.090450] 0000000000000000000000000000000000000000000000000000000000000000
[ 6.090455] ... APIC ESR: 00000000
[ 6.090460] ... APIC ICR: 000008fd
[ 6.090460] ... APIC ICR2: 02000000
[ 6.090463] ... APIC LVTT: 000200ef
[ 6.090465] ... APIC LVTPC: 00010000
[ 6.090467] ... APIC LVT0: 00010700
[ 6.090470] ... APIC LVT1: 00000400
[ 6.090472] ... APIC LVTERR: 000000fe
[ 6.090475] ... APIC TMICT: 0003d07e
[ 6.090478] ... APIC TMCCT: 00013d3d
[ 6.090480] ... APIC TDCR: 00000003
[ 6.090481]
[ 6.090482] number of MP IRQ sources: 15.
[ 6.090482] number of IO-APIC #0 registers: 24.
[ 6.090483] testing the IO APIC.......................
[ 6.090498] IO APIC #0......
[ 6.090498] .... register #00: 00000000
[ 6.090499] ....... : physical APIC id: 00
[ 6.090499] ....... : Delivery Type: 0
[ 6.090500] ....... : LTS : 0
[ 6.090500] .... register #01: 00170011
[ 6.090501] ....... : max redirection entries: 17
[ 6.090501] ....... : PRQ implemented: 0
[ 6.090501] ....... : IO APIC version: 11
[ 6.090502] .... register #02: 00000000
[ 6.090502] ....... : arbitration: 00
[ 6.090503] .... IRQ redirection table:
[ 6.090513] 1 0 0 0 0 0 0 00
[ 6.090522] 0 0 0 0 0 1 1 31
[ 6.090531] 0 0 0 0 0 1 1 30
[ 6.090540] 0 0 0 0 0 1 1 33
[ 6.090550] 1 0 0 0 0 1 1 34
[ 6.090559] 1 1 0 0 0 1 1 35
[ 6.090568] 0 0 0 0 0 1 1 36
[ 6.090578] 0 0 0 0 0 1 1 37
[ 6.090587] 0 0 0 0 0 1 1 38
[ 6.090596] 0 1 0 0 0 1 1 39
[ 6.090605] 1 1 0 0 0 1 1 3A
[ 6.090614] 1 1 0 0 0 1 1 3B
[ 6.090624] 0 0 0 0 0 1 1 3C
[ 6.090633] 0 0 0 0 0 1 1 3D
[ 6.090642] 0 0 0 0 0 1 1 3E
[ 6.090652] 0 0 0 0 0 1 1 3F
[ 6.090661] 1 0 0 0 0 0 0 00
[ 6.090670] 1 0 0 0 0 0 0 00
[ 6.090679] 1 0 0 0 0 0 0 00
[ 6.090688] 1 0 0 0 0 0 0 00
[ 6.090697] 1 0 0 0 0 0 0 00
[ 6.090706] 1 0 0 0 0 0 0 00
[ 6.090715] 1 0 0 0 0 0 0 00
[ 6.090724] 1 0 0 0 0 0 0 00
[ 6.090725] IRQ to pin mappings:
[ 6.090728] IRQ0 -> 0:2
[ 6.090729] IRQ1 -> 0:1
[ 6.090730] IRQ3 -> 0:3
[ 6.090731] IRQ4 -> 0:4
[ 6.090732] IRQ5 -> 0:5
[ 6.090733] IRQ6 -> 0:6
[ 6.090734] IRQ7 -> 0:7
[ 6.090735] IRQ8 -> 0:8
[ 6.090736] IRQ9 -> 0:9
[ 6.090737] IRQ10 -> 0:10
[ 6.090738] IRQ11 -> 0:11
[ 6.090739] IRQ12 -> 0:12
[ 6.090740] IRQ13 -> 0:13
[ 6.090741] IRQ14 -> 0:14
[ 6.090742] IRQ15 -> 0:15
[ 6.090743] .................................... done.
[ 6.090744] Using IPI Shortcut mode
[ 6.090936] Loading compiled-in X.509 certificates
[ 6.090950] Problem loading in-kernel X.509 certificate (-74)
[ 6.091365] bio: create slab <bio-1> at 1
[ 6.091876] Btrfs loaded, debug=on, assert=on, integrity-checker=on
[ 6.092060] Key type trusted registered
[ 6.279514] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 6.282414] EDD information not available.
[ 6.284361] debug: unmapping init [mem 0x82039000-0x82218fff]
[ 6.286803] Write protecting the kernel text: 11652k
[ 6.288948] Write protecting the kernel read-only data: 4080k
[ 6.292582] Failed to execute /init (error -8)
[ 6.295125] Starting init: /sbin/init exists but couldn't execute it (error -8)
[ 6.299442] Starting init: /etc/init exists but couldn't execute it (error -13)
[ 6.302942] Starting init: /bin/sh exists but couldn't execute it (error -8)
[ 6.307438] Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[ 6.311314] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.14.0-rc5-00009-g4dea8e4 #6
[ 6.311314] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 6.311314] 00000000 00000000 8f037f74 81b48a98 8f803770 8f037f98 81b3d3fa 81e07204
[ 6.311314] 82233ec0 81df9b08 81df98af 8f803770 81f717e0 00000000 8f037fac 81b38dfc
[ 6.311314] 81df9cd0 81df989f fffffff8 8f036000 81b5fd3b 81b38d30 00000000 00000000
[ 6.311314] Call Trace:
[ 6.311314] [<81b48a98>] dump_stack+0x48/0x60
[ 6.311314] [<81b3d3fa>] panic+0x82/0x180
[ 6.311314] [<81b38dfc>] kernel_init+0xcc/0xe0
[ 6.311314] [<81b5fd3b>] ret_from_kernel_thread+0x1b/0x30
[ 6.311314] [<81b38d30>] ? rest_init+0xc0/0xc0
[ 6.311314] Kernel Offset: 0x0 from 0x81000000 (relocation range: 0x80000000-0x907fdfff)
wfg@bee ~/linux/obj-compiletest% kvm-0day.sh arch/x86/boot/bzImage
early console in setup code
Probing EDD (edd=off to disable)... ok
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.14.0-rc5-00009-g4dea8e4 (wfg@bee) (gcc version 4.6.3 (Debian 4.6.3-1) ) #6 SMP Fri Mar 7 18:30:39 CST 2014
[ 0.000000] KERNEL supported cpus:
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] CPU: vendor_id 'GenuineIntel' unknown, using generic init.
[ 0.000000] CPU: Your system may be unstable.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000000fffdfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000fffe000-0x000000000fffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
[ 0.000000] debug: ignoring loglevel setting.
[ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[ 0.000000] SMBIOS 2.4 present.
[ 0.000000] DMI: Bochs Bochs, BIOS Bochs 01/01/2011
[ 0.000000] Hypervisor detected: KVM
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0xfffe max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: write-back
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0080000000 mask FF80000000 uncachable
[ 0.000000] 1 disabled
[ 0.000000] 2 disabled
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] Scan for SMP in [mem 0x00000000-0x000003ff]
[ 0.000000] Scan for SMP in [mem 0x0009fc00-0x0009ffff]
[ 0.000000] Scan for SMP in [mem 0x000f0000-0x000fffff]
[ 0.000000] found SMP MP-table at [mem 0x000f1840-0x000f184f] mapped at [800f1840]
[ 0.000000] mpc: f1850-f193c
[ 0.000000] initial memory mapped: [mem 0x00000000-0x02bfffff]
[ 0.000000] Base memory trampoline at [8009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x0f800000-0x0fbfffff]
[ 0.000000] [mem 0x0f800000-0x0fbfffff] page 4k
[ 0.000000] BRK [0x02790000, 0x02790fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x08000000-0x0f7fffff]
[ 0.000000] [mem 0x08000000-0x0f7fffff] page 4k
[ 0.000000] BRK [0x02791000, 0x02791fff] PGTABLE
[ 0.000000] BRK [0x02792000, 0x02792fff] PGTABLE
[ 0.000000] BRK [0x02793000, 0x02793fff] PGTABLE
[ 0.000000] BRK [0x02794000, 0x02794fff] PGTABLE
[ 0.000000] BRK [0x02795000, 0x02795fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x07ffffff]
[ 0.000000] [mem 0x00100000-0x07ffffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x0fc00000-0x0fffdfff]
[ 0.000000] [mem 0x0fc00000-0x0fffdfff] page 4k
[ 0.000000] RAMDISK: [mem 0x0fce6000-0x0ffeffff]
[ 0.000000] ACPI: RSDP 000f16b0 000014 (v00 BOCHS )
[ 0.000000] ACPI: RSDT 0fffe3f0 000034 (v01 BOCHS BXPCRSDT 00000001 BXPC 00000001)
[ 0.000000] ACPI: FACP 0fffff80 000074 (v01 BOCHS BXPCFACP 00000001 BXPC 00000001)
[ 0.000000] ACPI: DSDT 0fffe430 001137 (v01 BXPC BXDSDT 00000001 INTL 20100528)
[ 0.000000] ACPI: FACS 0fffff40 000040
[ 0.000000] ACPI: SSDT 0ffff6a0 000899 (v01 BOCHS BXPCSSDT 00000001 BXPC 00000001)
[ 0.000000] ACPI: APIC 0ffff5b0 000080 (v01 BOCHS BXPCAPIC 00000001 BXPC 00000001)
[ 0.000000] ACPI: HPET 0ffff570 000038 (v01 BOCHS BXPCHPET 00000001 BXPC 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] mapped APIC to ffff9000 ( fee00000)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 255MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 0fffe000
[ 0.000000] low ram: 0 - 0fffe000
[ 0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00
[ 0.000000] kvm-clock: cpu 0, msr 0:fffb001, boot clock
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] Normal [mem 0x01000000-0x0fffdfff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0x0fffdfff]
[ 0.000000] On node 0 totalpages: 65436
[ 0.000000] free_area_init_node: node 0, pgdat 8200a2e0, node_mem_map 8f951028
[ 0.000000] DMA zone: 40 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3998 pages, LIFO batch:0
[ 0.000000] Normal zone: 600 pages used for memmap
[ 0.000000] Normal zone: 61438 pages, LIFO batch:15
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0xb008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] mapped APIC to ffff9000 ( fee00000)
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 0, APIC INT 02
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level)
[ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 05, APIC ID 0, APIC INT 05
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 0, APIC INT 09
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level)
[ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0a, APIC ID 0, APIC INT 0a
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level)
[ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 0b, APIC ID 0, APIC INT 0b
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 0, APIC INT 01
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 0, APIC INT 03
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 0, APIC INT 04
[ 0.000000] ACPI: IRQ5 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 0, APIC INT 06
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 0, APIC INT 07
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 0, APIC INT 08
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ10 used by override.
[ 0.000000] ACPI: IRQ11 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 0, APIC INT 0c
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 0, APIC INT 0d
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 0, APIC INT 0e
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 0, APIC INT 0f
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] mapped IOAPIC to ffff8000 (fec00000)
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] e820: [mem 0x10000000-0xfeffbfff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on KVM
[ 0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 330 pages/cpu @8f6bd000 s1338976 r0 d12704 u1351680
[ 0.000000] pcpu-alloc: s1338976 r0 d12704 u1351680 alloc=330*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] kvm-clock: cpu 0, msr 0:fffb001, primary cpu clock
[ 0.000000] KVM setup async PF for cpu 0
[ 0.000000] kvm-stealtime: cpu 0, msr f6bf540
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64796
[ 0.000000] Kernel command line: debug sched_debug apic=debug ignore_loglevel earlyprintk=ttyS0,115200 sysrq_always_enabled panic=10 prompt_ramdisk=0 console=ttyS0,115200 console=tty0 vga=normal root=/dev/ram0 rw
[ 0.000000] sysrq: sysrq always enabled.
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 228784K/261744K available (11650K kernel code, 875K rwdata, 4076K rodata, 1920K init, 5512K bss, 32960K reserved, 0K highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xffa93000 - 0xfffff000 (5552 kB)
[ 0.000000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.000000] vmalloc : 0x907fe000 - 0xff3fe000 (1772 MB)
[ 0.000000] lowmem : 0x80000000 - 0x8fffe000 ( 255 MB)
[ 0.000000] .init : 0x82039000 - 0x82219000 (1920 kB)
[ 0.000000] .data : 0x81b60dce - 0x82037fe0 (4956 kB)
[ 0.000000] .text : 0x81000000 - 0x81b60dce (11651 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU debugfs-based tracing is enabled.
[ 0.000000] Hierarchical RCU autobalancing is disabled.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Additional per-CPU info printed with stalls.
[ 0.000000] RCU restricting CPUs from NR_CPUS=32 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:2304 nr_irqs:512 16
[ 0.000000] CPU 0 irqstacks, hard=8f00a000 soft=8f00c000
[ 0.000000] ACPI: Core revision 20131218
[ 0.000000] ACPI: All ACPI Tables successfully acquired
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] console [ttyS0] enabled
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3807 kB
[ 0.000000] per task-struct memory footprint: 1920 bytes
[ 0.000000] ------------------------
[ 0.000000] | Locking API testsuite:
[ 0.000000] ----------------------------------------------------------------------------
[ 0.000000] | spin |wlock |rlock |mutex | wsem | rsem |
[ 0.000000] --------------------------------------------------------------------------
[ 0.000000] A-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-B-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-B-C-C-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-C-A-B-C deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-B-C-C-D-D-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-C-D-B-D-D-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] A-B-C-D-B-C-D-A deadlock:failed|failed| ok |failed|failed|failed|
[ 0.000000] double unlock: ok | ok | ok | ok | ok | ok |
[ 0.000000] initialize held: ok | ok | ok | ok | ok | ok |
[ 0.000000] bad unlock order: ok | ok | ok | ok | ok | ok |
[ 0.000000] --------------------------------------------------------------------------
[ 0.000000] recursive read-lock: | ok | |failed|
[ 0.000000] recursive read-lock #2: | ok | |failed|
[ 0.000000] mixed read-write-lock: |failed| |failed|
[ 0.000000] mixed write-read-lock: |failed| |failed|
[ 0.000000] --------------------------------------------------------------------------
[ 0.000000] hard-irqs-on + irq-safe-A/12:failed|failed| ok |
[ 0.000000] soft-irqs-on + irq-safe-A/12:failed|failed| ok |
[ 0.000000] hard-irqs-on + irq-safe-A/21:failed|failed| ok |
[ 0.000000] soft-irqs-on + irq-safe-A/21:failed|failed| ok |
[ 0.000000] sirq-safe-A => hirqs-on/12:failed|failed| ok |
[ 0.000000] sirq-safe-A => hirqs-on/21:failed|failed| ok |
[ 0.000000] hard-safe-A + irqs-on/12:failed|failed| ok |
[ 0.000000] soft-safe-A + irqs-on/12:failed|failed| ok |
[ 0.000000] hard-safe-A + irqs-on/21:failed|failed| ok |
[ 0.000000] soft-safe-A + irqs-on/21:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/123:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/123:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/132:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/132:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/213:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/213:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/231:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/231:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/312:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/312:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #1/321:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #1/321:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/123:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/123:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/132:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/132:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/213:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/213:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/231:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/231:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/312:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/312:failed|failed| ok |
[ 0.000000] hard-safe-A + unsafe-B #2/321:failed|failed| ok |
[ 0.000000] soft-safe-A + unsafe-B #2/321:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/123:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/123:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/132:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/132:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/213:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/213:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/231:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/231:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/312:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/312:failed|failed| ok |
[ 0.000000] hard-irq lock-inversion/321:failed|failed| ok |
[ 0.000000] soft-irq lock-inversion/321:failed|failed| ok |
[ 0.000000] hard-irq read-recursion/123: ok |
[ 0.000000] soft-irq read-recursion/123: ok |
[ 0.000000] hard-irq read-recursion/132: ok |
[ 0.000000] soft-irq read-recursion/132: ok |
[ 0.000000] hard-irq read-recursion/213: ok |
[ 0.000000] soft-irq read-recursion/213: ok |
[ 0.000000] hard-irq read-recursion/231: ok |
[ 0.000000] soft-irq read-recursion/231: ok |
[ 0.000000] hard-irq read-recursion/312: ok |
[ 0.000000] soft-irq read-recursion/312: ok |
[ 0.000000] hard-irq read-recursion/321: ok |
[ 0.000000] soft-irq read-recursion/321: ok |
[ 0.000000] --------------------------------------------------------------------------
[ 0.000000] | Wound/wait tests |
[ 0.000000] ---------------------
[ 0.000000] ww api failures: ok | ok | ok |
[ 0.000000] ww contexts mixing:failed| ok |
[ 0.000000] finishing ww context: ok | ok | ok | ok |
[ 0.000000] locking mismatches: ok | ok | ok |
[ 0.000000] EDEADLK handling: ok | ok | ok | ok | ok | ok | ok | ok | ok | ok |
[ 0.000000] spinlock nest unlocked: ok |
[ 0.000000] -----------------------------------------------------
[ 0.000000] |block | try |context|
[ 0.000000] -----------------------------------------------------
[ 0.000000] context:failed| ok | ok |
[ 0.000000] try:failed| ok |failed|
[ 0.000000] block:failed| ok |failed|
[ 0.000000] spinlock:failed| ok |failed|
[ 0.000000] --------------------------------------------------------
[ 0.000000] 141 out of 253 testcases failed, as expected. |
[ 0.000000] ----------------------------------------------------
[ 0.000000] ODEBUG: 15 of 15 active objects replaced
[ 0.000000] ODEBUG: selftest passed
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Detected 2693.508 MHz processor
[ 0.000000] tsc: Marking TSC unstable due to TSCs unsynchronized
[ 0.012000] Calibrating delay loop (skipped) preset value.. 5387.01 BogoMIPS (lpj=10774032)
[ 0.013239] pid_max: default: 4096 minimum: 301
[ 0.014788] Mount-cache hash table entries: 512
[ 0.016841] Initializing cgroup subsys debug
[ 0.018735] Initializing cgroup subsys devices
[ 0.020032] Initializing cgroup subsys freezer
[ 0.022158] Initializing cgroup subsys net_cls
[ 0.024010] Initializing cgroup subsys blkio
[ 0.026123] Initializing cgroup subsys perf_event
[ 0.028028] Initializing cgroup subsys net_prio
[ 0.032182] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.032182] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[ 0.032182] tlb_flushall_shift: -1
[ 0.042916] debug: unmapping init [mem 0x82219000-0x82221fff]
[ 0.052889] Getting VERSION: 50014
[ 0.054861] Getting VERSION: 50014
[ 0.056029] Getting ID: 0
[ 0.057585] Getting ID: f000000
[ 0.060027] Getting LVT0: 8700
[ 0.061087] Getting LVT1: 8400
[ 0.062078] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.064098] enabled ExtINT on CPU#0
[ 0.066960] ENABLING IO-APIC IRQs
[ 0.068027] init IO_APIC IRQs
[ 0.069426] apic 0 pin 0 not connected
[ 0.072024] IOAPIC[0]: Set routing entry (0-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:1)
[ 0.074175] IOAPIC[0]: Set routing entry (0-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:1)
[ 0.076065] IOAPIC[0]: Set routing entry (0-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:1)
[ 0.080045] IOAPIC[0]: Set routing entry (0-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:1)
[ 0.084060] IOAPIC[0]: Set routing entry (0-5 -> 0x35 -> IRQ 5 Mode:1 Active:0 Dest:1)
[ 0.087259] IOAPIC[0]: Set routing entry (0-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:1)
[ 0.088050] IOAPIC[0]: Set routing entry (0-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:1)
[ 0.092050] IOAPIC[0]: Set routing entry (0-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:1)
[ 0.096060] IOAPIC[0]: Set routing entry (0-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:1)
[ 0.100025] IOAPIC[0]: Set routing entry (0-10 -> 0x3a -> IRQ 10 Mode:1 Active:0 Dest:1)
[ 0.104061] IOAPIC[0]: Set routing entry (0-11 -> 0x3b -> IRQ 11 Mode:1 Active:0 Dest:1)
[ 0.108060] IOAPIC[0]: Set routing entry (0-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:1)
[ 0.112043] IOAPIC[0]: Set routing entry (0-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:1)
[ 0.116060] IOAPIC[0]: Set routing entry (0-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:1)
[ 0.120052] IOAPIC[0]: Set routing entry (0-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:1)
[ 0.124052] apic 0 pin 16 not connected
[ 0.126099] apic 0 pin 17 not connected
[ 0.128011] apic 0 pin 18 not connected
[ 0.129923] apic 0 pin 19 not connected
[ 0.132006] apic 0 pin 20 not connected
[ 0.133808] apic 0 pin 21 not connected
[ 0.136011] apic 0 pin 22 not connected
[ 0.137961] apic 0 pin 23 not connected
[ 0.140159] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.142130] smpboot: CPU0: GenuineIntel Common KVM processor (fam: 0f, model: 06, stepping: 01)
[ 0.145090] Using local APIC timer interrupts.
[ 0.145090] calibrating APIC timer ...
[ 0.148000] ... lapic delta = 6251195
[ 0.148000] ... PM-Timer delta = 358135
[ 0.148000] ... PM-Timer result ok
[ 0.148000] ..... delta 6251195
[ 0.148000] ..... mult: 268486780
[ 0.148000] ..... calibration result: 4000764
[ 0.148000] ..... CPU clock speed is 2694.3929 MHz.
[ 0.148000] ..... host bus clock speed is 1000.0764 MHz.
[ 0.148073] Performance Events: no PMU driver, software events only.
[ 0.153410] CPU 1 irqstacks, hard=8f086000 soft=8f090000
[ 0.155354] x86: Booting SMP configuration:
[ 0.156005] .... node #0, CPUs: #1
[ 0.012000] Initializing CPU#1
[ 0.012000] kvm-clock: cpu 1, msr 0:fffb021, secondary cpu clock
[ 0.012000] masked ExtINT on CPU#1
[ 0.173562] x86: Booted up 1 node, 2 CPUs
[ 0.173503] KVM setup async PF for cpu 1
[ 0.173503] kvm-stealtime: cpu 1, msr f809540
[ 0.176009] ----------------
[ 0.180008] | NMI testsuite:
[ 0.181618] --------------------
[ 0.183352] remote IPI: ok |
[ 0.197253] local IPI: ok |
[ 0.220032] --------------------
[ 0.222522] Good, all 2 testcases passed! |
[ 0.224014] ---------------------------------
[ 0.228016] smpboot: Total of 2 processors activated (10774.03 BogoMIPS)
[ 0.232552] CPU0 attaching sched-domain:
[ 0.236033] domain 0: span 0-1 level CPU
[ 0.239014] groups: 0 1
[ 0.241193] CPU1 attaching sched-domain:
[ 0.244047] domain 0: span 0-1 level CPU
[ 0.246266] groups: 1 0
[ 0.249006] devtmpfs: initialized
[ 0.254320] xor: measuring software checksum speed
[ 0.296018] pIII_sse : 123.000 MB/sec
[ 0.336054] prefetch64-sse: 134.000 MB/sec
[ 0.339007] xor: using function: prefetch64-sse (134.000 MB/sec)
[ 0.340040] atomic64 test passed for i386+ platform with CX8 and with SSE
[ 0.348255] regulator-dummy: no parameters
[ 0.351838] NET: Registered protocol family 16
[ 0.352660] cpuidle: using governor ladder
[ 0.356018] cpuidle: using governor menu
[ 0.359544] ACPI: bus type PCI registered
[ 0.360116] PCI: PCI BIOS revision 2.10 entry at 0xfd4e3, last bus=0
[ 0.364007] PCI: Using configuration type 1 for base access
[ 0.380569] bio: create slab <bio-0> at 0
[ 0.452010] raid6: mmxx1 2865 MB/s
[ 0.520027] raid6: mmxx2 2605 MB/s
[ 0.588025] raid6: sse1x1 1969 MB/s
[ 0.656019] raid6: sse1x2 2600 MB/s
[ 0.724040] raid6: sse2x1 3953 MB/s
[ 0.792022] raid6: sse2x2 4016 MB/s
[ 0.795132] raid6: using algorithm sse2x2 (4016 MB/s)
[ 0.796022] raid6: using intx1 recovery algorithm
[ 0.800529] ACPI: Added _OSI(Module Device)
[ 0.802740] ACPI: Added _OSI(Processor Device)
[ 0.804025] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.806010] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.824533] ACPI: Interpreter enabled
[ 0.826471] ACPI: (supports S0 S5)
[ 0.828010] ACPI: Using IOAPIC for interrupt routing
[ 0.830175] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.852392] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.855676] acpi PNP0A03:00: _OSC: OS supports [Segments]
[ 0.856045] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.860328] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
[ 0.864155] PCI host bridge to bus 0000:00
[ 0.868007] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.870474] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.872013] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.876014] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.880026] pci_bus 0000:00: root bus resource [mem 0x80000000-0xfebfffff]
[ 0.883039] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000
[ 0.885106] pci 0000:00:01.0: [8086:7000] type 00 class 0x060100
[ 0.892011] pci 0000:00:01.1: [8086:7010] type 00 class 0x010180
[ 0.900574] pci 0000:00:01.1: reg 0x20: [io 0xc060-0xc06f]
[ 0.906231] pci 0000:00:01.3: [8086:7113] type 00 class 0x068000
[ 0.908701] pci 0000:00:01.3: quirk: [io 0xb000-0xb03f] claimed by PIIX4 ACPI
[ 0.912017] pci 0000:00:01.3: quirk: [io 0xb100-0xb10f] claimed by PIIX4 SMB
[ 0.916691] pci 0000:00:02.0: [1013:00b8] type 00 class 0x030000
[ 0.921217] pci 0000:00:02.0: reg 0x10: [mem 0xfc000000-0xfdffffff pref]
[ 0.925494] pci 0000:00:02.0: reg 0x14: [mem 0xfebe2000-0xfebe2fff]
[ 0.944144] pci 0000:00:02.0: reg 0x30: [mem 0xfebd0000-0xfebdffff pref]
[ 0.949320] pci 0000:00:03.0: [1af4:1000] type 00 class 0x020000
[ 0.954123] pci 0000:00:03.0: reg 0x10: [io 0xc040-0xc05f]
[ 0.958005] pci 0000:00:03.0: reg 0x14: [mem 0xfebe1000-0xfebe1fff]
[ 0.971679] pci 0000:00:03.0: reg 0x30: [mem 0xfebc0000-0xfebcffff pref]
[ 0.972831] pci 0000:00:04.0: [8086:100e] type 00 class 0x020000
[ 0.981034] pci 0000:00:04.0: reg 0x10: [mem 0xfeb80000-0xfeb9ffff]
[ 0.985031] pci 0000:00:04.0: reg 0x14: [io 0xc000-0xc03f]
[ 0.998016] pci 0000:00:04.0: reg 0x30: [mem 0xfeba0000-0xfebbffff pref]
[ 1.000744] pci 0000:00:05.0: [8086:25ab] type 00 class 0x088000
[ 1.005121] pci 0000:00:05.0: reg 0x10: [mem 0xfebe0000-0xfebe000f]
[ 1.016720] pci_bus 0000:00: on NUMA node 0
[ 1.020298] ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11)
[ 1.023955] ACPI: PCI Interrupt Link [LNKB] (IRQs 5 *10 11)
[ 1.025745] ACPI: PCI Interrupt Link [LNKC] (IRQs 5 10 *11)
[ 1.029747] ACPI: PCI Interrupt Link [LNKD] (IRQs 5 10 *11)
[ 1.033602] ACPI: PCI Interrupt Link [LNKS] (IRQs *9)
[ 1.038254] ACPI: Enabled 16 GPEs in block 00 to 0F
[ 1.041747] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 1.041747] vgaarb: loaded
[ 1.044006] vgaarb: bridge control possible 0000:00:02.0
[ 1.045494] SCSI subsystem initialized
[ 1.048077] libata version 3.00 loaded.
[ 1.049699] ACPI: bus type USB registered
[ 1.049699] usbcore: registered new interface driver usbfs
[ 1.051363] usbcore: registered new interface driver hub
[ 1.054886] usbcore: registered new device driver usb
[ 1.054886] pps_core: LinuxPPS API ver. 1 registered
[ 1.056008] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.060026] PTP clock support registered
[ 1.061477] PCI: Using ACPI for IRQ routing
[ 1.062863] PCI: pci_cache_line_size set to 64 bytes
[ 1.064172] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 1.066094] e820: reserve RAM buffer [mem 0x0fffe000-0x0fffffff]
[ 1.068488] irda_init()
[ 1.069467] NET: Registered protocol family 23
[ 1.071111] Bluetooth: Core ver 2.18
[ 1.072059] NET: Registered protocol family 31
[ 1.073583] Bluetooth: HCI device and connection manager initialized
[ 1.076047] Bluetooth: HCI socket layer initialized
[ 1.077729] Bluetooth: L2CAP socket layer initialized
[ 1.080067] Bluetooth: SCO socket layer initialized
[ 1.083492] cfg80211: Calling CRDA to update world regulatory domain
[ 1.085850] Switched to clocksource kvm-clock
[ 1.086476] FS-Cache: Loaded
[ 1.087540] CacheFiles: Loaded
[ 1.088326] pnp: PnP ACPI init
[ 1.089499] ACPI: bus type PNP registered
[ 1.091018] IOAPIC[0]: Set routing entry (0-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:3)
[ 1.095831] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.098067] IOAPIC[0]: Set routing entry (0-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:3)
[ 1.101027] pnp 00:01: Plug and Play ACPI device, IDs PNP0303 (active)
[ 1.103307] IOAPIC[0]: Set routing entry (0-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:3)
[ 1.106173] pnp 00:02: Plug and Play ACPI device, IDs PNP0f13 (active)
[ 1.108414] IOAPIC[0]: Set routing entry (0-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:3)
[ 1.111180] pnp 00:03: [dma 2]
[ 1.112355] pnp 00:03: Plug and Play ACPI device, IDs PNP0700 (active)
[ 1.114644] IOAPIC[0]: Set routing entry (0-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:3)
[ 1.117451] pnp 00:04: Plug and Play ACPI device, IDs PNP0400 (active)
[ 1.119710] IOAPIC[0]: Set routing entry (0-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:3)
[ 1.122606] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active)
[ 1.125192] pnp 00:06: Plug and Play ACPI device, IDs PNP0103 (active)
[ 1.127582] pnp: PnP ACPI: found 7 devices
[ 1.129024] ACPI: bus type PNP unregistered
[ 1.169081] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 1.171304] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 1.174802] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.177509] pci_bus 0000:00: resource 7 [mem 0x80000000-0xfebfffff]
[ 1.179415] NET: Registered protocol family 2
[ 1.181393] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.184156] TCP bind hash table entries: 2048 (order: 4, 90112 bytes)
[ 1.186264] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.188508] TCP: reno registered
[ 1.189846] UDP hash table entries: 128 (order: 1, 12288 bytes)
[ 1.191454] UDP-Lite hash table entries: 128 (order: 1, 12288 bytes)
[ 1.193572] NET: Registered protocol family 1
[ 1.195116] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[ 1.197312] pci 0000:00:01.0: PIIX3: Enabling Passive Release
[ 1.199390] pci 0000:00:01.0: Activating ISA DMA hang workarounds
[ 1.201786] pci 0000:00:02.0: Boot video device
[ 1.203392] PCI: CLS 0 bytes, default 64
[ 1.205211] Unpacking initramfs...
[ 2.144177] debug: unmapping init [mem 0x8fce6000-0x8ffeffff]
[ 2.147910] cryptomgr_test (24) used greatest stack depth: 7292 bytes left
[ 2.151185] cryptomgr_test (25) used greatest stack depth: 7280 bytes left
[ 2.153527] PCLMULQDQ-NI instructions are not detected.
[ 2.156056] The force parameter has not been set to 1. The Iris poweroff handler will not be installed.
[ 2.159347] NatSemi SCx200 Driver
[ 2.162103] futex hash table entries: 16 (order: -3, 768 bytes)
[ 2.164977] Initialise system trusted keyring
[ 2.168199] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 2.176426] VFS: Disk quotas dquot_6.5.2
[ 2.178681] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.183159] DLM installed
[ 2.186719] NTFS driver 2.1.30 [Flags: R/O DEBUG].
[ 2.188662] ocfs2 stack glue: unable to register sysctl
[ 2.191364] ocfs2: Registered cluster interface o2cb
[ 2.194015] OCFS2 User DLM kernel interface loaded
[ 2.199885] msgmni has been set to 446
[ 2.211434] Key type asymmetric registered
[ 2.214822] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 2.220812] io scheduler noop registered (default)
[ 2.224495] io scheduler deadline registered
[ 2.227018] io scheduler cfq registered
[ 2.228119] list_sort_test: start testing list_sort()
[ 2.230879] test_string_helpers: Running tests...
[ 2.234133] no IO addresses supplied
[ 2.235090] usbcore: registered new interface driver udlfb
[ 2.236513] usbcore: registered new interface driver smscufx
[ 2.238550] kworker/u4:0 (84) used greatest stack depth: 6880 bytes left
[ 2.240651] uvesafb: failed to execute /sbin/v86d
[ 2.242872] uvesafb: make sure that the v86d helper is installed and executable
[ 2.246171] uvesafb: Getting VBE info block failed (eax=0x4f00, err=-8)
[ 2.248827] uvesafb: vbe_init() failed with -22
[ 2.251067] uvesafb: probe of uvesafb.0 failed with error -22
[ 2.253577] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 2.255701] ACPI: Power Button [PWRF]
[ 2.257880] r3964: Philips r3964 Driver $Revision: 1.10 $
[ 2.259530] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 2.284028] 00:05: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[ 2.288377] STMicroelectronics ASC driver initialized
[ 2.290753] serial: Freescale lpuart driver
[ 2.292439] lp: driver loaded but no devices found
[ 2.294304] toshiba: not a supported Toshiba laptop
[ 2.296553] ppdev: user-space parallel port driver
[ 2.298283] scx200_gpio: no SCx200 gpio present
[ 2.300338] platform pc8736x_gpio.0: NatSemi pc8736x GPIO Driver Initializing
[ 2.302529] platform pc8736x_gpio.0: no device found
[ 2.304102] nsc_gpio initializing
[ 2.305447] telclk_interrupt = 0xf non-mcpbl0010 hw.
[ 2.307289] SyncLink PC Card driver $Revision: 4.34 $, tty major#245
[ 2.309348] Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin is 60 seconds).
[ 2.312871] Hangcheck: Using getrawmonotonic().
[ 2.315519] parport_pc 00:04: reported by Plug and Play ACPI
[ 2.318497] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 2.419484] lp0: using parport0 (interrupt-driven).
[ 2.423671] Floppy drive(s): fd0 is 1.44M
[ 2.426951] loop: module loaded
[ 2.428451] rbd: loaded
[ 2.430781] blk-mq: CPU -> queue map
[ 2.433632] CPU 0 -> Queue 0
[ 2.436028] CPU 1 -> Queue 0
[ 2.438413] nullb0: unknown partition table
[ 2.441605] blk-mq: CPU -> queue map
[ 2.443556] CPU 0 -> Queue 0
[ 2.443762] FDC 0 is a S82078B
[ 2.448480] CPU 1 -> Queue 0
[ 2.450945] nullb1: unknown partition table
[ 2.454439] null: module loaded
[ 2.456686] zram: Created 1 device(s) ...
[ 2.458470] dummy-irq: no IRQ given. Use irq=N
[ 2.461813] lkdtm: No crash points registered, enable through debugfs
[ 2.465940] Silicon Labs C2 port support v. 0.51.0 - (C) 2007 Rodolfo Giometti
[ 2.471533] c2port c2port0: C2 port uc added
[ 2.474727] c2port c2port0: uc flash has 30 blocks x 512 bytes (15360 bytes total)
[ 2.479449] usbcore: registered new interface driver viperboard
[ 2.481564] Uniform Multi-Platform E-IDE driver
[ 2.483379] piix 0000:00:01.1: IDE controller (0x8086:0x7010 rev 0x00)
[ 2.487142] piix 0000:00:01.1: not 100% native mode: will probe irqs later
[ 2.491290] ide0: BM-DMA at 0xc060-0xc067
[ 2.494425] ide1: BM-DMA at 0xc068-0xc06f
[ 2.497995] Probing IDE interface ide0...
[ 3.071490] Probing IDE interface ide1...
[ 3.807704] hdc: QEMU DVD-ROM, ATAPI CD/DVD-ROM drive
[ 4.479819] hdc: host max PIO4 wanted PIO255(auto-tune) selected PIO0
[ 4.481162] hdc: MWDMA2 mode selected
[ 4.482148] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 4.483103] ide1 at 0x170-0x177,0x376 on irq 15
[ 4.484318] ide-gd driver 1.18
[ 4.486936] Loading iSCSI transport class v2.0-870.
[ 4.488297] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[ 4.490501] osd: LOADED open-osd 0.2.1
[ 4.492000] Rounding down aligned max_sectors from 4294967295 to 4294967288
[ 4.497752] SSFDC read-only Flash Translation layer
[ 4.500682] L440GX flash mapping: failed to find PIIX4 ISA bridge, cannot continue
[ 4.504856] Failed to ioremap_nocache
[ 4.506917] slram: not enough parameters.
[ 4.637135] parport0: AVR Butterfly
[ 4.638705] parport0: cannot grant exclusive access for device spi-lm70llp
[ 4.640675] spi-lm70llp: spi_lm70llp probe fail, status -12
[ 4.642699] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[ 4.646731] eql: Equalizer2002: Simon Janes (simon@ncm.com) and David S. Miller (davem@redhat.com)
[ 4.652318] tun: Universal TUN/TAP device driver, 1.6
[ 4.653988] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 4.656106] arcnet loaded.
[ 4.657079] arcnet: RFC1201 "standard" (`a') encapsulation support loaded.
[ 4.659069] arcnet: RFC1051 "simple standard" (`s') encapsulation support loaded.
[ 4.661508] arcnet: raw mode (`r') encapsulation support loaded.
[ 4.664165] arcnet: cap mode (`c') encapsulation support loaded.
[ 4.665717] arcnet: COM90xx chipset support
[ 4.965550] S3: No ARCnet cards found.
[ 4.967958] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[ 4.970933] ipddp0: Appletalk-IP Decap. mode by Jay Schulist <jschlst@samba.org>
[ 4.973765] slcan: serial line CAN interface driver
[ 4.975461] slcan: 10 dynamic interface channels.
[ 4.977081] CAN device driver interface
[ 4.978601] usbcore: registered new interface driver ems_usb
[ 4.980515] usbcore: registered new interface driver esd_usb2
[ 4.982530] usbcore: registered new interface driver kvaser_usb
[ 4.983821] usbcore: registered new interface driver peak_usb
[ 4.985107] usbcore: registered new interface driver usb_8dev
[ 4.986368] sja1000 CAN netdevice driver
[ 4.987275] sja1000_isa: insufficient parameters supplied
[ 4.988535] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
[ 4.990325] usbcore: registered new interface driver irda-usb
[ 4.991610] usbcore: registered new interface driver stir4200
[ 4.993330] usbcore: registered new interface driver mcs7780
[ 4.994699] usbcore: registered new interface driver kingsun-sir
[ 4.995980] usbcore: registered new interface driver ks959-sir
[ 4.997500] NET3 PLIP version 2.4-parport gniibe@mri.co.jp
[ 4.998694] plip0: Parallel port at 0x378, using IRQ 7.
[ 5.002085] PPP generic driver version 2.4.2
[ 5.003402] PPP BSD Compression module registered
[ 5.004728] PPP Deflate Compression module registered
[ 5.006778] PPP MPPE Compression module registered
[ 5.008871] NET: Registered protocol family 24
[ 5.010958] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
[ 5.013234] usbcore: registered new interface driver kaweth
[ 5.015802] usbcore: registered new interface driver r8152
[ 5.018389] usbcore: registered new interface driver cdc_phonet
[ 5.020610] parport0: cannot grant exclusive access for device ks0108
[ 5.023161] ks0108: ERROR: parport didn't register new device
[ 5.025900] cfag12864b: ERROR: ks0108 is not initialized
[ 5.028474] cfag12864bfb: ERROR: cfag12864b is not initialized
[ 5.032765] aoe: AoE v85 initialised.
[ 5.034955] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.037822] ehci-pci: EHCI PCI platform driver
[ 5.039056] ehci-platform: EHCI generic platform driver
[ 5.040627] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.042299] ohci-pci: OHCI PCI platform driver
[ 5.043600] ohci-platform: OHCI generic platform driver
[ 5.045224] driver u132_hcd
[ 5.047001] fusbh200_hcd: FUSBH200 Host Controller (EHCI) Driver
[ 5.050641] Warning! fusbh200_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 5.057585] fotg210_hcd: FOTG210 Host Controller (EHCI) Driver
[ 5.061313] 4Warning! fotg210_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 5.068248] usbcore: registered new interface driver cdc_acm
[ 5.071628] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 5.077308] usbcore: registered new interface driver usblp
[ 5.079054] usbcore: registered new interface driver cdc_wdm
[ 5.080698] usbcore: registered new interface driver usbtmc
[ 5.082344] usbcore: registered new interface driver usb-storage
[ 5.083628] usbcore: registered new interface driver ums-alauda
[ 5.085186] usbcore: registered new interface driver ums-cypress
[ 5.086807] usbcore: registered new interface driver ums_eneub6250
[ 5.088367] usbcore: registered new interface driver ums-jumpshot
[ 5.089855] usbcore: registered new interface driver ums-sddr09
[ 5.091309] usbcore: registered new interface driver ums-usbat
[ 5.092789] usbcore: registered new interface driver mdc800
[ 5.095100] mdc800: v0.7.5 (30/10/2000):USB Driver for Mustek MDC800 Digital Camera
[ 5.098140] usbcore: registered new interface driver microtekX6
[ 5.100493] usbcore: registered new interface driver usbserial
[ 5.102613] usbcore: registered new interface driver usbserial_generic
[ 5.104776] usbserial: USB Serial support registered for generic
[ 5.106999] usbcore: registered new interface driver aircable
[ 5.109678] usbserial: USB Serial support registered for aircable
[ 5.112632] usbcore: registered new interface driver ark3116
[ 5.115323] usbserial: USB Serial support registered for ark3116
[ 5.118294] usbcore: registered new interface driver belkin_sa
[ 5.120153] usbserial: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
[ 5.122693] usbcore: registered new interface driver ch341
[ 5.123973] usbserial: USB Serial support registered for ch341-uart
[ 5.125390] usbcore: registered new interface driver cp210x
[ 5.126805] usbserial: USB Serial support registered for cp210x
[ 5.128650] usbcore: registered new interface driver cyberjack
[ 5.131294] usbserial: USB Serial support registered for Reiner SCT Cyberjack USB card reader
[ 5.135471] usbcore: registered new interface driver cypress_m8
[ 5.137726] usbserial: USB Serial support registered for DeLorme Earthmate USB
[ 5.140291] usbserial: USB Serial support registered for HID->COM RS232 Adapter
[ 5.142815] usbserial: USB Serial support registered for Nokia CA-42 V2 Adapter
[ 5.145777] usbcore: registered new interface driver usb_debug
[ 5.148460] usbserial: USB Serial support registered for debug
[ 5.151218] usbcore: registered new interface driver digi_acceleport
[ 5.153116] usbserial: USB Serial support registered for Digi 2 port USB adapter
[ 5.155729] usbserial: USB Serial support registered for Digi 4 port USB adapter
[ 5.158447] usbcore: registered new interface driver empeg
[ 5.159999] usbserial: USB Serial support registered for empeg
[ 5.161458] usbcore: registered new interface driver ftdi_sio
[ 5.162861] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 5.164781] usbcore: registered new interface driver ipw
[ 5.166056] usbserial: USB Serial support registered for IPWireless converter
[ 5.167772] usbcore: registered new interface driver keyspan
[ 5.169937] usbserial: USB Serial support registered for Keyspan - (without firmware)
[ 5.172584] usbserial: USB Serial support registered for Keyspan 1 port adapter
[ 5.175522] usbserial: USB Serial support registered for Keyspan 2 port adapter
[ 5.179215] usbserial: USB Serial support registered for Keyspan 4 port adapter
[ 5.183082] usbcore: registered new interface driver metro_usb
[ 5.185851] usbserial: USB Serial support registered for Metrologic USB to Serial
[ 5.189657] usbcore: registered new interface driver mos7840
[ 5.192279] usbserial: USB Serial support registered for Moschip 7840/7820 USB Serial Driver
[ 5.195874] usbcore: registered new interface driver mxuport
[ 5.197283] usbserial: USB Serial support registered for MOXA UPort
[ 5.199390] usbcore: registered new interface driver navman
[ 5.201171] usbserial: USB Serial support registered for navman
[ 5.203981] usbcore: registered new interface driver omninet
[ 5.206699] usbserial: USB Serial support registered for ZyXEL - omni.net lcd plus usb
[ 5.210607] usbcore: registered new interface driver opticon
[ 5.213337] usbserial: USB Serial support registered for opticon
[ 5.216133] usbcore: registered new interface driver option
[ 5.218357] usbserial: USB Serial support registered for GSM modem (1-port)
[ 5.220033] usbcore: registered new interface driver qcaux
[ 5.221423] usbserial: USB Serial support registered for qcaux
[ 5.223681] usbcore: registered new interface driver qcserial
[ 5.226458] usbserial: USB Serial support registered for Qualcomm USB modem
[ 5.229354] usbcore: registered new interface driver usb_serial_simple
[ 5.232092] usbserial: USB Serial support registered for zio
[ 5.234250] usbserial: USB Serial support registered for funsoft
[ 5.236556] usbserial: USB Serial support registered for flashloader
[ 5.238280] usbserial: USB Serial support registered for vivopay
[ 5.239657] usbserial: USB Serial support registered for moto_modem
[ 5.241745] usbserial: USB Serial support registered for hp4x
[ 5.243999] usbserial: USB Serial support registered for suunto
[ 5.245584] usbserial: USB Serial support registered for siemens_mpi
[ 5.246997] usbcore: registered new interface driver spcp8x5
[ 5.248229] usbserial: USB Serial support registered for SPCP8x5
[ 5.250686] usbcore: registered new interface driver ssu100
[ 5.252857] usbserial: USB Serial support registered for Quatech SSU-100 USB to Serial Driver
[ 5.256939] usbcore: registered new interface driver visor
[ 5.259281] usbserial: USB Serial support registered for Handspring Visor / Palm OS
[ 5.263216] usbserial: USB Serial support registered for Sony Clie 5.0
[ 5.266247] usbserial: USB Serial support registered for Sony Clie 3.5
[ 5.269106] usbcore: registered new interface driver wishbone_serial
[ 5.271921] usbserial: USB Serial support registered for wishbone_serial
[ 5.274225] usbcore: registered new interface driver whiteheat
[ 5.275752] usbserial: USB Serial support registered for Connect Tech - WhiteHEAT - (prerenumeration)
[ 5.279066] usbserial: USB Serial support registered for Connect Tech - WhiteHEAT
[ 5.281494] usbcore: registered new interface driver xsens_mt
[ 5.283329] usbserial: USB Serial support registered for xsens_mt
[ 5.285610] usbcore: registered new interface driver zte_ev
[ 5.287123] usbserial: USB Serial support registered for zte_ev
[ 5.289731] usbcore: registered new interface driver appledisplay
[ 5.292044] usbcore: registered new interface driver cytherm
[ 5.294238] usbcore: registered new interface driver emi26 - firmware loader
[ 5.296847] usbcore: registered new interface driver emi62 - firmware loader
[ 5.299079] driver ftdi-elan
[ 5.300378] usbcore: registered new interface driver ftdi-elan
[ 5.301749] usbcore: registered new interface driver idmouse
[ 5.302978] usbcore: registered new interface driver iowarrior
[ 5.304252] usbcore: registered new interface driver usblcd
[ 5.305493] usbcore: registered new interface driver usbled
[ 5.306719] usbcore: registered new interface driver legousbtower
[ 5.308025] usbcore: registered new interface driver rio500
[ 5.309271] usbcore: registered new interface driver uss720
[ 5.310518] uss720: v0.6:USB Parport Cable driver for Cables using the Lucent Technologies USS720 Chip
[ 5.312532] uss720: NOTE: this is a special purpose driver to allow nonstandard
[ 5.314207] uss720: protocols (eg. bitbang) over USS720 usb to parallel cables
[ 5.315878] uss720: If you just want to connect to a printer, use usblp instead
[ 5.317697] usbcore: registered new interface driver sisusb
[ 5.319244] i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
[ 5.321828] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 5.323217] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 5.369532] evbug: Connected device: input0 (Power Button at LNXPWRBN/button/input0)
[ 5.372520] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 5.376275] evbug: Connected device: input1 (AT Translated Set 2 keyboard at isa0060/serio0/input0)
[ 5.378423] usbcore: registered new interface driver appletouch
[ 5.379291] usbcore: registered new interface driver xpad
[ 5.380128] mk712: device not present
[ 5.380179] usbcore: registered new interface driver usbtouchscreen
[ 5.380671] apanel: Fujitsu BIOS signature 'FJKEYINF' not found...
[ 5.380718] usbcore: registered new interface driver ati_remote2
[ 5.380753] cm109: Keymap for Komunikate KIP1000 phone loaded
[ 5.380794] usbcore: registered new interface driver cm109
[ 5.380800] cm109: CM109 phone driver: 20080805 (C) Alfred E. Heggestad
[ 5.380939] usbcore: registered new interface driver keyspan_remote
[ 5.381044] usbcore: registered new interface driver powermate
[ 5.381059] wistron_btns: System unknown
[ 5.381100] i2c /dev entries driver
[ 5.381213] i2c-parport: adapter type unspecified
[ 5.381213] i2c-parport-light: adapter type unspecified
[ 5.381251] usbcore: registered new interface driver i2c-tiny-usb
[ 5.381255] scx200_i2c: no SCx200 gpio pins available
[ 5.381305] pps_ldisc: PPS line discipline registered
[ 5.381306] pps_parport: parallel port PPS client
[ 5.381311] parport0: cannot grant exclusive access for device pps_parport
[ 5.381312] pps_parport: couldn't register with parport0
[ 5.381367] Driver for 1-wire Dallas network protocol.
[ 5.381444] usbcore: registered new interface driver DS9490R
[ 5.381447] DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
[ 5.381492] 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
[ 5.381605] power_supply test_ac: uevent
[ 5.381608] power_supply test_ac: POWER_SUPPLY_NAME=test_ac
[ 5.381620] power_supply test_ac: prop ONLINE=1
[ 5.381660] power_supply test_ac: power_supply_changed
[ 5.381688] power_supply test_ac: power_supply_changed_work
[ 5.381692] power_supply test_ac: power_supply_update_gen_leds 1
[ 5.381703] power_supply test_ac: uevent
[ 5.381704] power_supply test_ac: POWER_SUPPLY_NAME=test_ac
[ 5.381709] power_supply test_ac: prop ONLINE=1
[ 5.381774] power_supply test_battery: uevent
[ 5.381775] power_supply test_battery: POWER_SUPPLY_NAME=test_battery
[ 5.381779] power_supply test_battery: prop STATUS=Discharging
[ 5.381781] power_supply test_battery: prop CHARGE_TYPE=Fast
[ 5.381783] power_supply test_battery: prop HEALTH=Good
[ 5.381784] power_supply test_battery: prop PRESENT=1
[ 5.381786] power_supply test_battery: prop TECHNOLOGY=Li-ion
[ 5.381788] power_supply test_battery: prop CHARGE_FULL_DESIGN=100
[ 5.381789] power_supply test_battery: prop CHARGE_FULL=100
[ 5.381791] power_supply test_battery: prop CHARGE_NOW=50
[ 5.381792] power_supply test_battery: prop CAPACITY=50
[ 5.381794] power_supply test_battery: prop CAPACITY_LEVEL=Normal
[ 5.381795] power_supply test_battery: prop TIME_TO_EMPTY_AVG=3600
[ 5.381797] power_supply test_battery: prop TIME_TO_FULL_NOW=3600
[ 5.381798] power_supply test_battery: prop MODEL_NAME=Test battery
[ 5.381800] power_supply test_battery: prop MANUFACTURER=Linux
[ 5.381801] power_supply test_battery: prop SERIAL_NUMBER=3.14.0-rc5-00009-g4dea8e4
[ 5.381803] power_supply test_battery: prop TEMP=26
[ 5.381804] power_supply test_battery: prop VOLTAGE_NOW=3300
[ 5.381956] power_supply test_battery: power_supply_changed
[ 5.381965] power_supply test_battery: power_supply_changed_work
[ 5.381968] power_supply test_battery: power_supply_update_bat_leds 2
[ 5.381972] power_supply test_battery: uevent
[ 5.381973] power_supply test_battery: POWER_SUPPLY_NAME=test_battery
[ 5.381983] power_supply test_battery: prop STATUS=Discharging
[ 5.381984] power_supply test_battery: prop CHARGE_TYPE=Fast
[ 5.381988] power_supply test_battery: prop HEALTH=Good
[ 5.381989] power_supply test_battery: prop PRESENT=1
[ 5.381991] power_supply test_battery: prop TECHNOLOGY=Li-ion
[ 5.381993] power_supply test_battery: prop CHARGE_FULL_DESIGN=100
[ 5.381995] power_supply test_battery: prop CHARGE_FULL=100
[ 5.381996] power_supply test_battery: prop CHARGE_NOW=50
[ 5.381998] power_supply test_battery: prop CAPACITY=50
[ 5.381999] power_supply test_battery: prop CAPACITY_LEVEL=Normal
[ 5.382001] power_supply test_battery: prop TIME_TO_EMPTY_AVG=3600
[ 5.382002] power_supply test_battery: prop TIME_TO_FULL_NOW=3600
[ 5.382004] power_supply test_battery: prop MODEL_NAME=Test battery
[ 5.382005] power_supply test_battery: prop MANUFACTURER=Linux
[ 5.382007] power_supply test_battery: prop SERIAL_NUMBER=3.14.0-rc5-00009-g4dea8e4
[ 5.382008] power_supply test_battery: prop TEMP=26
[ 5.382009] power_supply test_battery: prop VOLTAGE_NOW=3300
[ 5.382052] power_supply test_usb: uevent
[ 5.382052] power_supply test_usb: POWER_SUPPLY_NAME=test_usb
[ 5.382056] power_supply test_usb: prop ONLINE=1
[ 5.382064] power_supply test_usb: power_supply_changed
[ 5.382078] power_supply test_usb: power_supply_changed_work
[ 5.382082] power_supply test_usb: power_supply_update_gen_leds 1
[ 5.382085] power_supply test_usb: uevent
[ 5.382086] power_supply test_usb: POWER_SUPPLY_NAME=test_usb
[ 5.382089] power_supply test_usb: prop ONLINE=1
[ 5.383489] pc87360: PC8736x not detected, module not inserted
[ 5.383978] Bluetooth: Virtual HCI driver ver 1.4
[ 5.538244] Bluetooth: HCI UART driver ver 2.2
[ 5.539536] Bluetooth: HCI H4 protocol initialized
[ 5.540929] Bluetooth: HCI Three-wire UART (H5) protocol initialized
[ 5.542672] usbcore: registered new interface driver bcm203x
[ 5.544321] usbcore: registered new interface driver bpa10x
[ 5.545838] usbcore: registered new interface driver bfusb
[ 5.559827] ISDN subsystem Rev: 1.1.2.3/1.1.2.2/none/1.1.2.2/1.1.2.2
[ 5.563255] CAPI 2.0 started up with major 68 (middleware)
[ 5.565129] dss1_divert module successfully installed
[ 5.566923] gigaset: Driver for Gigaset 307x (debug build)
[ 5.568720] gigaset: Kernel CAPI interface
[ 5.570603] usbcore: registered new interface driver usb_gigaset
[ 5.572189] usb_gigaset: USB Driver for Gigaset 307x using M105
[ 5.576403] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 5.582360] usbcore: registered new interface driver usbhid
[ 5.585194] usbhid: USB HID core driver
[ 5.587641] oprofile: using timer interrupt.
[ 5.589959] NET: Registered protocol family 26
[ 5.592241] netem: version 1.3
[ 5.593885] u32 classifier
[ 5.595415] Performance counters on
[ 5.597331] input device check on
[ 5.599287] Netfilter messages via NETLINK v0.30.
[ 5.600682] nfnl_acct: registering with nfnetlink.
[ 5.601857] nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net>
[ 5.603427] nf_tables_compat: (c) 2012 Pablo Neira Ayuso <pablo@netfilter.org>
[ 5.606560] xt_time: kernel timezone is -0000
[ 5.608599] ip_set: protocol 6
[ 5.610285] IPVS: Registered protocols (TCP, UDP, SCTP, AH)
[ 5.612013] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[ 5.613906] IPVS: Each connection entry needs 256 bytes at least
[ 5.616864] IPVS: Creating netns size=1356 id=0
[ 5.619360] IPVS: ipvs loaded.
[ 5.620155] IPVS: [rr] scheduler registered.
[ 5.621169] IPVS: [wrr] scheduler registered.
[ 5.622193] IPVS: [lc] scheduler registered.
[ 5.623203] IPVS: [wlc] scheduler registered.
[ 5.624895] IPVS: [lblc] scheduler registered.
[ 5.627027] IPVS: [lblcr] scheduler registered.
[ 5.629132] IPVS: [dh] scheduler registered.
[ 5.631317] IPVS: [nq] scheduler registered.
[ 5.633322] ipip: IPv4 over IPv4 tunneling driver
[ 5.636224] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 5.639382] arp_tables: (C) 2002 David S. Miller
[ 5.641568] TCP: cubic registered
[ 5.643408] NET: Registered protocol family 17
[ 5.645473] NET: Registered protocol family 15
[ 5.647807] NET: Registered protocol family 5
[ 5.649939] NET: Registered protocol family 9
[ 5.651101] X25: Linux Version 0.2
[ 5.652850] can: controller area network core (rev 20120528 abi 9)
[ 5.655683] NET: Registered protocol family 29
[ 5.657795] can: raw protocol (rev 20120528)
[ 5.659743] can: netlink gateway (rev 20130117) max_hops=1
[ 5.662126] IrCOMM protocol (Dag Brattli)
[ 5.670299] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 5.671609] Bluetooth: BNEP filters: protocol
[ 5.672650] Bluetooth: BNEP socket layer initialized
[ 5.673776] Bluetooth: CMTP (CAPI Emulation) ver 1.0
[ 5.674913] Bluetooth: CMTP socket layer initialized
[ 5.676025] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 5.679822] Bluetooth: HIDP socket layer initialized
[ 5.683860] NET: Registered protocol family 33
[ 5.686828] Key type rxrpc registered
[ 5.688672] Key type rxrpc_s registered
[ 5.690693] cryptomgr_probe (111) used greatest stack depth: 6748 bytes left
[ 5.690726] RxRPC: Registered security type 2 'rxkad'
[ 5.690756] l2tp_core: L2TP core driver, V2.0
[ 5.690769] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 5.690793] l2tp_debugfs: L2TP debugfs support
[ 5.690794] NET4: DECnet for Linux: V.2.5.68s (C) 1995-2003 Linux DECnet Project Team
[ 5.690927] DECnet: Routing cache hash table of 256 buckets, 11Kbytes
[ 5.690976] NET: Registered protocol family 12
[ 5.691013] NET: Registered protocol family 35
[ 5.691107] 8021q: 802.1Q VLAN Support v1.8
[ 5.691635] DCCP: Activated CCID 2 (TCP-like)
[ 5.691648] DCCP: Activated CCID 3 (TCP-Friendly Rate Control)
[ 5.692019] sctp: Hash tables configured (established 1365 bind 1489)
[ 5.692166] tipc: Activated (version 2.0.0)
[ 5.693601] NET: Registered protocol family 30
[ 5.694182] tipc: Started in single node mode
[ 5.694415] NET: Registered protocol family 37
[ 5.694550] Key type dns_resolver registered
[ 5.694591] Key type ceph registered
[ 5.694974] libceph: loaded (mon/osd proto 15/24)
[ 5.695448] batman_adv: B.A.T.M.A.N. advanced 2014.1.0 (compatibility version 15) loaded
[ 5.695450] openvswitch: Open vSwitch switching datapath
[ 5.695668] mpls_gso: MPLS GSO support
[ 5.696312]
[ 5.696312] printing PIC contents
[ 5.696330] ... PIC IMR: ffff
[ 5.696340] ... PIC IRR: 1053
[ 5.696357] ... PIC ISR: 0000
[ 5.696366] ... PIC ELCR: 0c00
[ 5.696389] printing local APIC contents on CPU#0/0:
[ 5.696405] ... APIC ID: 00000000 (0)
[ 5.696411] ... APIC VERSION: 00050014
[ 5.696418] ... APIC TASKPRI: 00000000 (00)
[ 5.696424] ... APIC PROCPRI: 00000000
[ 5.696430] ... APIC LDR: 01000000
[ 5.696436] ... APIC DFR: ffffffff
[ 5.696441] ... APIC SPIV: 000001ff
[ 5.696442] ... APIC ISR field:
[ 5.696486] 0000000000000000000000000000000000000000000000000000000000000000
[ 5.696487] ... APIC TMR field:
[ 5.696528] 0000000000000000000000000000000000000000000000000000000000000000
[ 5.696529] ... APIC IRR field:
[ 5.696569] 0000000000000000000000000000000000000000000000000000000000000000
[ 5.696580] ... APIC ESR: 00000000
[ 5.696590] ... APIC ICR: 000008fd
[ 5.696591] ... APIC ICR2: 02000000
[ 5.696597] ... APIC LVTT: 000200ef
[ 5.696602] ... APIC LVTPC: 00010000
[ 5.696608] ... APIC LVT0: 00010700
[ 5.696613] ... APIC LVT1: 00000400
[ 5.696619] ... APIC LVTERR: 000000fe
[ 5.696625] ... APIC TMICT: 0003d0bf
[ 5.696631] ... APIC TMCCT: 0001b473
[ 5.696637] ... APIC TDCR: 00000003
[ 5.696638]
[ 5.696640] number of MP IRQ sources: 15.
[ 5.696641] number of IO-APIC #0 registers: 24.
[ 5.696642] testing the IO APIC.......................
[ 5.696675] IO APIC #0......
[ 5.696676] .... register #00: 00000000
[ 5.696677] ....... : physical APIC id: 00
[ 5.696678] ....... : Delivery Type: 0
[ 5.696679] ....... : LTS : 0
[ 5.696680] .... register #01: 00170011
[ 5.696681] ....... : max redirection entries: 17
[ 5.696681] ....... : PRQ implemented: 0
[ 5.696682] ....... : IO APIC version: 11
[ 5.696683] .... register #02: 00000000
[ 5.696684] ....... : arbitration: 00
[ 5.696685] .... IRQ redirection table:
[ 5.696707] 1 0 0 0 0 0 0 00
[ 5.696729] 0 0 0 0 0 1 1 31
[ 5.696753] 0 0 0 0 0 1 1 30
[ 5.696763] 0 0 0 0 0 1 1 33
[ 5.696772] 1 0 0 0 0 1 1 34
[ 5.696781] 1 1 0 0 0 1 1 35
[ 5.696790] 0 0 0 0 0 1 1 36
[ 5.696822] 0 0 0 0 0 1 1 37
[ 5.696843] 0 0 0 0 0 1 1 38
[ 5.696863] 0 1 0 0 0 1 1 39
[ 5.696884] 1 1 0 0 0 1 1 3A
[ 5.696904] 1 1 0 0 0 1 1 3B
[ 5.696925] 0 0 0 0 0 1 1 3C
[ 5.696946] 0 0 0 0 0 1 1 3D
[ 5.696967] 0 0 0 0 0 1 1 3E
[ 5.696987] 0 0 0 0 0 1 1 3F
[ 5.697008] 1 0 0 0 0 0 0 00
[ 5.697028] 1 0 0 0 0 0 0 00
[ 5.697049] 1 0 0 0 0 0 0 00
[ 5.697069] 1 0 0 0 0 0 0 00
[ 5.697090] 1 0 0 0 0 0 0 00
[ 5.697110] 1 0 0 0 0 0 0 00
[ 5.697131] 1 0 0 0 0 0 0 00
[ 5.697151] 1 0 0 0 0 0 0 00
[ 5.697152] IRQ to pin mappings:
[ 5.697157] IRQ0 -> 0:2
[ 5.697159] IRQ1 -> 0:1
[ 5.697162] IRQ3 -> 0:3
[ 5.697164] IRQ4 -> 0:4
[ 5.697166] IRQ5 -> 0:5
[ 5.697168] IRQ6 -> 0:6
[ 5.697170] IRQ7 -> 0:7
[ 5.697172] IRQ8 -> 0:8
[ 5.697174] IRQ9 -> 0:9
[ 5.697177] IRQ10 -> 0:10
[ 5.697179] IRQ11 -> 0:11
[ 5.697181] IRQ12 -> 0:12
[ 5.697184] IRQ13 -> 0:13
[ 5.697186] IRQ14 -> 0:14
[ 5.697188] IRQ15 -> 0:15
[ 5.697189] .................................... done.
[ 5.697190] Using IPI Shortcut mode
[ 5.889704] Loading compiled-in X.509 certificates
[ 5.890857] Problem loading in-kernel X.509 certificate (-74)
[ 5.892573] bio: create slab <bio-1> at 1
[ 5.894338] Btrfs loaded, debug=on, assert=on, integrity-checker=on
[ 5.897689] Key type trusted registered
[ 5.900830] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 5.903528] EDD information not available.
[ 5.905654] debug: unmapping init [mem 0x82039000-0x82218fff]
[ 5.908755] Write protecting the kernel text: 11652k
[ 5.911243] Write protecting the kernel read-only data: 4080k
[ 5.913835] Failed to execute /init (error -8)
[ 5.916046] Starting init: /sbin/init exists but couldn't execute it (error -8)
[ 5.918907] Starting init: /etc/init exists but couldn't execute it (error -13)
[ 5.921981] Starting init: /bin/sh exists but couldn't execute it (error -8)
[ 5.924289] Kernel panic - not syncing: No working init found. Try passing init= option to kernel. See Linux Documentation/init.txt for guidance.
[ 5.928232] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.14.0-rc5-00009-g4dea8e4 #6
[ 5.928232] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[ 5.928232] 00000000 00000000 8f037f74 81b48a98 8f803770 8f037f98 81b3d3fa 81e07204
[ 5.928232] 82233ec0 81df9b08 81df98af 8f803770 81f717e0 00000000 8f037fac 81b38dfc
[ 5.928232] 81df9cd0 81df989f fffffff8 8f036000 81b5fd3b 81b38d30 00000000 00000000
[ 5.928232] Call Trace:
[ 5.928232] [<81b48a98>] dump_stack+0x48/0x60
[ 5.928232] [<81b3d3fa>] panic+0x82/0x180
[ 5.928232] [<81b38dfc>] kernel_init+0xcc/0xe0
[ 5.928232] [<81b5fd3b>] ret_from_kernel_thread+0x1b/0x30
[ 5.928232] [<81b38d30>] ? rest_init+0xc0/0xc0
[ 5.928232] Kernel Offset: 0x0 from 0x81000000 (relocation range: 0x80000000-0x907fdfff)
next prev parent reply other threads:[~2014-03-07 10:37 UTC|newest]
Thread overview: 49+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-03-07 1:38 [x86, vdso] BUG: unable to handle kernel paging request at d34bd000 Fengguang Wu
2014-03-07 1:48 ` [x86, vdso] BUG: unable to handle kernel paging request at 91c24000 Fengguang Wu
2014-03-07 7:21 ` [x86, vdso] BUG: unable to handle kernel paging request at d34bd000 Stefani Seibold
2014-03-07 18:56 ` Andy Lutomirski
2014-03-07 21:53 ` Stefani Seibold
2014-03-07 23:07 ` Andy Lutomirski
2014-03-09 8:47 ` Stefani Seibold
2014-03-10 0:16 ` H. Peter Anvin
2014-03-10 3:18 ` Andy Lutomirski
2014-03-10 4:46 ` Andy Lutomirski
2014-03-10 14:59 ` H. Peter Anvin
[not found] ` <CA+55aFwKpBybz9S9A=+tcr1BbdzAbagL30Br2cak2GrdPH=hhA@mail.gmail.com>
2014-03-10 17:12 ` Andy Lutomirski
2014-03-10 17:24 ` H. Peter Anvin
2014-03-10 17:31 ` Andy Lutomirski
2014-03-10 17:38 ` H. Peter Anvin
2014-03-10 17:46 ` Andy Lutomirski
2014-03-10 17:48 ` H. Peter Anvin
2014-03-10 17:52 ` Andy Lutomirski
2014-03-10 17:58 ` H. Peter Anvin
2014-03-10 18:10 ` Andy Lutomirski
2014-03-10 17:49 ` H. Peter Anvin
2014-03-10 20:03 ` Stefani Seibold
2014-03-10 20:06 ` H. Peter Anvin
2014-03-10 20:19 ` Linus Torvalds
2014-03-10 21:20 ` Linus Torvalds
2014-03-10 21:43 ` Andy Lutomirski
2014-03-10 21:51 ` Dave Jones
2014-03-10 22:59 ` H. Peter Anvin
2014-03-10 23:32 ` [PATCH] x86: Remove CONFIG_X86_OOSTORE Dave Jones
2014-03-11 10:11 ` [x86, vdso] BUG: unable to handle kernel paging request at d34bd000 Ingo Molnar
2014-03-10 21:25 ` stefani
2014-03-10 21:39 ` Linus Torvalds
2014-03-10 21:53 ` stefani
2014-03-10 22:03 ` Andy Lutomirski
2014-03-10 22:36 ` Andy Lutomirski
2014-03-10 23:02 ` H. Peter Anvin
2014-03-10 21:29 ` stefani
2014-03-11 6:02 ` H. Peter Anvin
2014-03-07 8:47 ` Stefani Seibold
2014-03-07 9:15 ` Fengguang Wu
2014-03-07 9:57 ` Stefani Seibold
2014-03-07 10:21 ` Fengguang Wu
2014-03-07 16:06 ` Stefani Seibold
2014-03-07 23:12 ` H. Peter Anvin
2014-03-07 10:36 ` Fengguang Wu [this message]
2014-03-07 23:44 ` Fengguang Wu
2014-03-09 8:08 ` Stefani Seibold
2014-03-10 0:00 ` H. Peter Anvin
2014-03-10 19:41 ` Greg Kroah-Hartman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20140307103649.GA21708@localhost \
--to=fengguang.wu@intel.com \
--cc=gregkh@linuxfoundation.org \
--cc=hpa@linux.intel.com \
--cc=linux-kernel@vger.kernel.org \
--cc=stefani@seibold.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.