All of lore.kernel.org
 help / color / mirror / Atom feed
From: Lee Jones <lee.jones@linaro.org>
To: Linus Walleij <linus.walleij@linaro.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>,
	linux-kernel@vger.kernel.org, Silvio F <silvio.fricke@gmail.com>,
	Philipp Zabel <p.zabel@pengutronix.de>,
	Sascha Hauer <s.hauer@pengutronix.de>,
	Shawn Guo <shawn.guo@linaro.org>,
	Viresh Kumar <viresh.linux@gmail.com>,
	Shiraz Hashim <shiraz.hashim@st.com>,
	spear-devel@list.st.com
Subject: Re: [PATCH 4/6] mfd: stmpe: mask off unused blocks properly
Date: Thu, 17 Apr 2014 11:52:14 +0100	[thread overview]
Message-ID: <20140417105214.GN28725@lee--X1> (raw)
In-Reply-To: <1397659455-13638-5-git-send-email-linus.walleij@linaro.org>

> The STMPE driver would just read/modify/write the system control
> register on the STMPE1601, meaning it would not properly mask off
> the PWM block, which remained active if it was on at boot time.
> This makes sure the blocks are always masked off if they were
> active on boot, saving some power. Also rename the inconsistenty
> named STMPE1601 define for the PWM block activation.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
>  drivers/mfd/stmpe.c | 9 +++++++++
>  drivers/mfd/stmpe.h | 2 +-
>  2 files changed, 10 insertions(+), 1 deletion(-)

Patch looks good to me.

Acked-by: Lee Jones <lee.jones@linaro.org>

> diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
> index 692452442ead..065c923cb2a9 100644
> --- a/drivers/mfd/stmpe.c
> +++ b/drivers/mfd/stmpe.c
> @@ -606,9 +606,18 @@ static int stmpe1601_enable(struct stmpe *stmpe, unsigned int blocks,
>  
>  	if (blocks & STMPE_BLOCK_GPIO)
>  		mask |= STMPE1601_SYS_CTRL_ENABLE_GPIO;
> +	else
> +		mask &= ~STMPE1601_SYS_CTRL_ENABLE_GPIO;
>  
>  	if (blocks & STMPE_BLOCK_KEYPAD)
>  		mask |= STMPE1601_SYS_CTRL_ENABLE_KPC;
> +	else
> +		mask &= ~STMPE1601_SYS_CTRL_ENABLE_KPC;
> +
> +	if (blocks & STMPE_BLOCK_PWM)
> +		mask |= STMPE1601_SYS_CTRL_ENABLE_SPWM;
> +	else
> +		mask &= ~STMPE1601_SYS_CTRL_ENABLE_SPWM;
>  
>  	return __stmpe_set_bits(stmpe, STMPE1601_REG_SYS_CTRL, mask,
>  				enable ? mask : 0);
> diff --git a/drivers/mfd/stmpe.h b/drivers/mfd/stmpe.h
> index 6639f1b0fef5..9e4d21d37a11 100644
> --- a/drivers/mfd/stmpe.h
> +++ b/drivers/mfd/stmpe.h
> @@ -192,7 +192,7 @@ int stmpe_remove(struct stmpe *stmpe);
>  
>  #define STMPE1601_SYS_CTRL_ENABLE_GPIO		(1 << 3)
>  #define STMPE1601_SYS_CTRL_ENABLE_KPC		(1 << 1)
> -#define STMPE1601_SYSCON_ENABLE_SPWM		(1 << 0)
> +#define STMPE1601_SYS_CTRL_ENABLE_SPWM		(1 << 0)
>  
>  /* The 1601/2403 share the same masks */
>  #define STMPE1601_AUTOSLEEP_TIMEOUT_MASK	(0x7)

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

  reply	other threads:[~2014-04-17 10:52 UTC|newest]

Thread overview: 25+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-04-16 14:44 [PATCH 0/6] mfd/gpio: cleanup of STMPE driver Linus Walleij
2014-04-16 14:44 ` [PATCH 1/6] mfd: stmpe: root out static GPIO and IRQ assignments Linus Walleij
2014-04-17 10:49   ` Lee Jones
2014-04-23 11:39     ` Linus Walleij
2014-04-23 13:22       ` Lee Jones
2014-04-23 21:23         ` Linus Walleij
2014-04-28  9:25           ` Lee Jones
2014-04-16 14:44 ` [PATCH 2/6] mfd: stmpe: add optional regulators Linus Walleij
2014-04-17 10:30   ` Lee Jones
2014-04-23  8:38     ` Linus Walleij
2014-05-06 12:52   ` Shawn Guo
     [not found]     ` <CAF2Aj3gDTYvv+vqa3FPBVdgOLwqctH0bd+coN29TpR53jNYKhg@mail.gmail.com>
2014-05-08 21:15       ` Linus Walleij
2014-04-16 14:44 ` [PATCH 3/6] mfd: stmpe: prope properly from the device tree Linus Walleij
2014-04-17 10:44   ` Lee Jones
2014-04-23  8:52     ` Linus Walleij
2014-04-16 14:44 ` [PATCH 4/6] mfd: stmpe: mask off unused blocks properly Linus Walleij
2014-04-17 10:52   ` Lee Jones [this message]
2014-04-16 14:44 ` [PATCH 5/6] ARM: ux500: add VCC and VIO regulators to STMPE IC Linus Walleij
2014-04-16 14:44 ` [PATCH 6/6] gpio: stmpe: switch to use gpiolib irqchip helpers Linus Walleij
2014-04-17  6:11 ` [PATCH 0/6] mfd/gpio: cleanup of STMPE driver Shawn Guo
2014-04-17 13:28   ` Silvio Fricke
2014-04-17 13:28     ` [PATCH] ARM: dts: imx6: edmqmx6: add vcc and vio power supplies to stmpe Silvio Fricke
2014-04-23 11:43       ` Linus Walleij
2014-05-10  6:10       ` Shawn Guo
2014-04-19  5:07     ` [PATCH 0/6] mfd/gpio: cleanup of STMPE driver Shawn Guo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20140417105214.GN28725@lee--X1 \
    --to=lee.jones@linaro.org \
    --cc=linus.walleij@linaro.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=p.zabel@pengutronix.de \
    --cc=s.hauer@pengutronix.de \
    --cc=sameo@linux.intel.com \
    --cc=shawn.guo@linaro.org \
    --cc=shiraz.hashim@st.com \
    --cc=silvio.fricke@gmail.com \
    --cc=spear-devel@list.st.com \
    --cc=viresh.linux@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.