Re: [PATCH v7 2/4] ARM: dts: am437x-gp-evm: add support for parallel NAND flash

[Tony Lindgren <tony@atomide.com>]

* Pekon Gupta <pekon@ti.com> [140519 02:16]:
> Adds pinmux and DT node for Micron (MT29F4G08AB) x8 NAND device present on
> am437x-gp-evm board.
> (1) As NAND Flash data lines are muxed with eMMC, Thus at a given time either
>     eMMC or NAND can be enabled. Selection between eMMC and NAND is controlled:
>     (a) By dynamically driving following GPIO pin from software
>         SPI2_CS0(GPIO) == 0 NAND is selected (default)
>         SPI2_CS0(GPIO) == 1 eMMC is selected
>     (b) By statically using Jumper (J89) on the board

So which MMC controller has eMMC then? How do we select which one we
have enabled in the am437x-gp-evm.dts by default?

Regards,

Tony
 
> (2) As NAND device connnected to this board has page-size=4K and oob-size=224,
>     So ROM code expects boot-loaders to be flashed in BCH16 ECC scheme for
>     NAND boot.
> 
> Signed-off-by: Pekon Gupta <pekon@ti.com>
> Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
> ---
>  arch/arm/boot/dts/am437x-gp-evm.dts | 108 ++++++++++++++++++++++++++++++++++++
>  1 file changed, 108 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
> index 30ace1b..f432685 100644
> --- a/arch/arm/boot/dts/am437x-gp-evm.dts
> +++ b/arch/arm/boot/dts/am437x-gp-evm.dts
> @@ -150,6 +150,27 @@
>  			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
>  		>;
>  	};
> +
> +	nand_flash_x8: nand_flash_x8 {
> +		pinctrl-single,pins = <
> +			0x26c(PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* spi2_cs0.gpio/eMMCorNANDsel */
> +			0x0  (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
> +			0x4  (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
> +			0x8  (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
> +			0xc  (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
> +			0x10 (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
> +			0x14 (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
> +			0x18 (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
> +			0x1c (PIN_INPUT  | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
> +			0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
> +			0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpmc_wpn */
> +			0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0  */
> +			0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
> +			0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
> +			0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
> +			0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
> +		>;
> +	};
>  };
>  
>  &i2c0 {
> @@ -246,3 +267,90 @@
>  	phy_id = <&davinci_mdio>, <0>;
>  	phy-mode = "rgmii";
>  };
> +
> +&elm {
> +	status = "okay";
> +};
> +
> +&gpmc {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&nand_flash_x8>;
> +	ranges = <0 0 0 0x01000000>;	/* minimum GPMC partition = 16MB */
> +	nand@0,0 {
> +		reg = <0 0 4>;		/* device IO registers */
> +		ti,nand-ecc-opt = "bch8";
> +		ti,elm-id = <&elm>;
> +		nand-bus-width = <8>;
> +		gpmc,device-width = <1>;
> +		gpmc,sync-clk-ps = <0>;
> +		gpmc,cs-on-ns = <0>;
> +		gpmc,cs-rd-off-ns = <40>;
> +		gpmc,cs-wr-off-ns = <40>;
> +		gpmc,adv-on-ns = <0>;
> +		gpmc,adv-rd-off-ns = <25>;
> +		gpmc,adv-wr-off-ns = <25>;
> +		gpmc,we-on-ns = <0>;
> +		gpmc,we-off-ns = <20>;
> +		gpmc,oe-on-ns = <3>;
> +		gpmc,oe-off-ns = <30>;
> +		gpmc,access-ns = <30>;
> +		gpmc,rd-cycle-ns = <40>;
> +		gpmc,wr-cycle-ns = <40>;
> +		gpmc,wait-pin = <0>;
> +		gpmc,wait-on-read;
> +		gpmc,wait-on-write;
> +		gpmc,bus-turnaround-ns = <0>;
> +		gpmc,cycle2cycle-delay-ns = <0>;
> +		gpmc,clk-activation-ns = <0>;
> +		gpmc,wait-monitoring-ns = <0>;
> +		gpmc,wr-access-ns = <40>;
> +		gpmc,wr-data-mux-bus-ns = <0>;
> +		/* MTD partition table */
> +		/* All SPL-* partitions are sized to minimal length
> +		 * which can be independently programmable. For
> +		 * NAND flash this is equal to size of erase-block */
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		partition@0 {
> +			label = "NAND.SPL";
> +			reg = <0x00000000 0x00040000>;
> +		};
> +		partition@1 {
> +			label = "NAND.SPL.backup1";
> +			reg = <0x00040000 0x00040000>;
> +		};
> +		partition@2 {
> +			label = "NAND.SPL.backup2";
> +			reg = <0x00080000 0x00040000>;
> +		};
> +		partition@3 {
> +			label = "NAND.SPL.backup3";
> +			reg = <0x000c0000 0x00040000>;
> +		};
> +		partition@4 {
> +			label = "NAND.u-boot-spl-os";
> +			reg = <0x00100000 0x00080000>;
> +		};
> +		partition@5 {
> +			label = "NAND.u-boot";
> +			reg = <0x00180000 0x00100000>;
> +		};
> +		partition@6 {
> +			label = "NAND.u-boot-env";
> +			reg = <0x00280000 0x00040000>;
> +		};
> +		partition@7 {
> +			label = "NAND.u-boot-env.backup1";
> +			reg = <0x002c0000 0x00040000>;
> +		};
> +		partition@8 {
> +			label = "NAND.kernel";
> +			reg = <0x00300000 0x00700000>;
> +		};
> +		partition@9 {
> +			label = "NAND.file-system";
> +			reg = <0x00a00000 0x1f600000>;
> +		};
> +	};
> +};
> -- 
> 1.8.5.1.163.gd7aced9
>