From: Magnus Damm <magnus.damm@gmail.com>
To: linux-sh@vger.kernel.org
Subject: [PATCH 01/03] ARM: shmobile: r8a7790: SYS-DMAC prototype
Date: Tue, 03 Jun 2014 22:33:04 +0000 [thread overview]
Message-ID: <20140603223304.2193.1096.sendpatchset@w520> (raw)
From: Magnus Damm <damm+renesas@opensource.se>
Prototype code to enable part of the SYS-DMAC on r8a7790.
Written to exercise the SYS-DMAC - Not for upstream merge.
Based on the following patch by Kuninori Morimoto-san:
"Local: ARM: shmobile: r8a7790: add SYS-DMAC support"
This patch enables SYS-DMAC0 (= Low), it doesn't support
SYS-DMAC1 (= HI) today.
Because, SYS-DMAC HI/Low interrupt mapping is not
good match to SH-DMAC driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: Do not call r8a7790_register_sys_dmac()
in r8a7790_add_standard_devices() as it is already called via
r8a7790_add_dt_devices()]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
[damm+renesas@opensource.se: Remove SDHI bits, also remove legacy
code path to make sure to cover only the DT reference case]
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
---
Applies to renesas-devel-v3.15-rc7-20140530
arch/arm/mach-shmobile/setup-r8a7790.c | 89 ++++++++++++++++++++++++++++----
1 file changed, 80 insertions(+), 9 deletions(-)
--- 0001/arch/arm/mach-shmobile/setup-r8a7790.c
+++ work/arch/arm/mach-shmobile/setup-r8a7790.c 2014-06-03 21:24:37.000000000 +0900
@@ -32,6 +32,84 @@
#include <mach/r8a7790.h>
#include <asm/mach/arch.h>
+#define DMAE_CHANNEL(a, b) \
+{ \
+ .offset = (a) - 0x20, \
+ .dmars = (a) - 0x20 + 0x40, \
+ .chclr_bit = (b), \
+ .chclr_offset = 0x80 - 0x20, \
+}
+
+/* Sys-DMAC */
+#define SYS_DMAC_SLAVE(_id, _bit, _addr, toffset, roffset, t, r) \
+{ \
+ .slave_id = SYS_DMAC_SLAVE_## _id ##_TX, \
+ .addr = _addr + toffset, \
+ .chcr = CHCR_TX(XMIT_SZ_## _bit ##BIT), \
+ .mid_rid = t, \
+}, { \
+ .slave_id = SYS_DMAC_SLAVE_## _id ##_RX, \
+ .addr = _addr + roffset, \
+ .chcr = CHCR_RX(XMIT_SZ_## _bit ##BIT), \
+ .mid_rid = r, \
+}
+
+static const struct sh_dmae_slave_config r8a7790_sys_dmac_slaves[] = {
+};
+
+static const struct sh_dmae_channel r8a7790_sys_dmac_channels[] = {
+ DMAE_CHANNEL(0x8000, 0),
+ DMAE_CHANNEL(0x8080, 1),
+ DMAE_CHANNEL(0x8100, 2),
+ DMAE_CHANNEL(0x8180, 3),
+ DMAE_CHANNEL(0x8200, 4),
+ DMAE_CHANNEL(0x8280, 5),
+ DMAE_CHANNEL(0x8300, 6),
+ DMAE_CHANNEL(0x8380, 7),
+ DMAE_CHANNEL(0x8400, 8),
+ DMAE_CHANNEL(0x8480, 9),
+ DMAE_CHANNEL(0x8500, 10),
+ DMAE_CHANNEL(0x8580, 11),
+ DMAE_CHANNEL(0x8600, 12),
+ DMAE_CHANNEL(0x8680, 13),
+ DMAE_CHANNEL(0x8700, 14),
+};
+
+static struct sh_dmae_pdata r8a7790_sys_dmac_platform_data = {
+ .slave = r8a7790_sys_dmac_slaves,
+ .slave_num = ARRAY_SIZE(r8a7790_sys_dmac_slaves),
+ .channel = r8a7790_sys_dmac_channels,
+ .channel_num = ARRAY_SIZE(r8a7790_sys_dmac_channels),
+ .ts_low_shift = TS_LOW_SHIFT,
+ .ts_low_mask = TS_LOW_BIT << TS_LOW_SHIFT,
+ .ts_high_shift = TS_HI_SHIFT,
+ .ts_high_mask = TS_HI_BIT << TS_HI_SHIFT,
+ .ts_shift = dma_ts_shift,
+ .ts_shift_num = ARRAY_SIZE(dma_ts_shift),
+ .dmaor_init = DMAOR_DME,
+ .chclr_present = 1,
+ .chclr_bitwise = 1,
+};
+
+static struct resource r8a7790_sys_dmac_resources[] = {
+ /* Channel registers and DMAOR for low */
+ DEFINE_RES_MEM(0xe6700020, 0x8763 - 0x20),
+ DEFINE_RES_IRQ(gic_spi(197)),
+ DEFINE_RES_NAMED(gic_spi(200), 15, NULL, IORESOURCE_IRQ),
+
+ /*
+ * HI is not supported
+ * since IRQ has strange mapping
+ */
+};
+
+#define r8a7790_register_sys_dmac(id) \
+ platform_device_register_resndata( \
+ &platform_bus, "sh-dma-engine", 2 + id, \
+ &r8a7790_sys_dmac_resources[id * 3], 3, \
+ &r8a7790_sys_dmac_platform_data, \
+ sizeof(r8a7790_sys_dmac_platform_data))
+
/* Audio-DMAC */
#define AUDIO_DMAC_SLAVE(_id, _addr, t, r) \
{ \
@@ -59,14 +137,6 @@ static const struct sh_dmae_slave_config
AUDIO_DMAC_SLAVE(SSI9, 0xec241240, 0x13, 0x14),
};
-#define DMAE_CHANNEL(a, b) \
-{ \
- .offset = (a) - 0x20, \
- .dmars = (a) - 0x20 + 0x40, \
- .chclr_bit = (b), \
- .chclr_offset = 0x80 - 0x20, \
-}
-
static const struct sh_dmae_channel r8a7790_audio_dmac_channels[] = {
DMAE_CHANNEL(0x8000, 0),
DMAE_CHANNEL(0x8080, 1),
@@ -282,6 +352,7 @@ static struct resource cmt0_resources[]
void __init r8a7790_add_dt_devices(void)
{
r8a7790_register_cmt(0);
+ r8a7790_register_sys_dmac(0);
}
void __init r8a7790_add_standard_devices(void)
@@ -296,7 +367,7 @@ void __init r8a7790_add_standard_devices
r8a7790_register_scif(7);
r8a7790_register_scif(8);
r8a7790_register_scif(9);
- r8a7790_add_dt_devices();
+ r8a7790_register_cmt(0);
r8a7790_register_irqc(0);
r8a7790_register_thermal();
r8a7790_register_i2c(0);
reply other threads:[~2014-06-03 22:33 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20140603223304.2193.1096.sendpatchset@w520 \
--to=magnus.damm@gmail.com \
--cc=linux-sh@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.