Linux version 2.6.35.3 (matt@matt-pc) (gcc version 4.6.3 (Timesys 20120917) ) #2 Fri Jun 13 09:50:08 EST 2014 CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: Freescale MX28 Memory policy: ECC disabled, Data cache writeback On node 0 totalpages: 32768 free_area_init_node: node 0, pgdat c0501924, node_mem_map c057f000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 224 pages used for memmap Normal zone: 28448 pages, LIFO batch:7 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyAM0,115200n8 ubi.mtd=1 root=/dev/ubiblkb rootfstype=squashfs rw rootwait panic=15 gpmi PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 124320k/124320k available, 6752k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xfde00000 - 0xffe00000 ( 32 MB) vmalloc : 0xc8800000 - 0xf0000000 ( 632 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc0039000 ( 196 kB) .text : 0xc0039000 - 0xc04d1000 (4704 kB) .data : 0xc04d2000 - 0xc0505d00 ( 208 kB) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:288 Console: colour dummy device 80x30 console [ttyAM0] enabled ODEBUG: 0 of 0 active objects replaced Calibrating delay loop... 178.99 BogoMIPS (lpj=894976) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok devtmpfs: initialized regulator: core version 0.5 NET: Registered protocol family 16 regulator: vddd: 800 <--> 1575 mV at 1500 mV fast normal regulator: vdddbo: 800 <--> 1575 mV fast normal regulator: vdda: 1500 <--> 2275 mV at 1800 mV fast normal vddio = 3380000, val=10 regulator: vddio: 2880 <--> 3680 mV at 3380 mV fast normal regulator: overall_current: fast normal regulator: vbus5v: regulator: mxs-duart-1: fast normal regulator: mxs-bl-1: fast normal regulator: mxs-i2c-1: fast normal regulator: mmc_ssp-1: fast normal regulator: mmc_ssp-2: fast normal regulator: charger-1: fast normal regulator: power-test-1: fast normal regulator: cpufreq-1: fast normal maxwell_init_machine: starting... i.MX IRAM pool: 124 KB@0xc8820000 Initializing GPMI pins Initializing GPIO pins 9523 FULL_PW_EN on 9523 powered off mx28_init_mmc: ......adding device hdq_init:gpio_request 124 hdq_init:IRQ 252 battery_gauge_init: Adding bq27x00 maxwell_init_machine: done... usb DR wakeup device is registered IMX usb wakeup probe the wakeup pdata is 0xc04da38c audit: cannot initialize inotify handle bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Advanced Linux Sound Architecture Driver Version 1.0.23. cfg80211: Calling CRDA to update world regulatory domain Switching to clocksource mxs clock source NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 Bus freq driver module loaded mxs_cpu_init: cpufreq init finished audit: initializing netlink socket (disabled) type=2000 audit(1.010:1): initialized squashfs: version 4.0 (2009/01/31) Phillip Lougher Registering unionfs 2.5.11 (for 2.6.35.14) JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.14) msgmni has been set to 242 alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered (default) Console: switching to colour frame buffer device 100x30 mxs-duart.0: ttyAM0 at MMIO 0x80074000 (irq = 47) is a DebugUART mxs-auart.0: ttySP0 at MMIO 0x8006a000 (irq = 112) is a mxs-auart.0 Found APPUART 3.1.0 mxs-auart.1: ttySP1 at MMIO 0x8006c000 (irq = 113) is a mxs-auart.1 Found APPUART 3.1.0 mxs-auart.2: ttySP2 at MMIO 0x8006e000 (irq = 114) is a mxs-auart.2 Found APPUART 3.1.0 brd: module loaded loop: module loaded Loading iSCSI transport class v2.0-870. i.MX GPMI NFC NFC: Version 1, 8-chip GPMI and BCH Boot ROM: Version 1, Single-chip boot area, block mark swapping supported Scanning for NAND Flash chips... ----------------------------- NAND Flash Device Information ----------------------------- Manufacturer : Micron (0x2c) Device Code : 0xda Cell Technology : SLC Chip Size : 256 MiB Pages per Block : 64 Page Geometry : 2048+64 ECC Strength : 4 bits ECC Size : 512 B Data Setup Time : 20 ns Data Hold Time : 10 ns Address Setup Time: 10 ns GPMI Sample Delay : 6 ns tREA : Unknown tRLOH : Unknown tRHOH : Unknown Description : MT29F2G08 ------------ NFC Geometry ------------ ECC Algorithm : BCH ECC Strength : 8 Page Size in Bytes : 2112 Metadata Size in Bytes : 10 ECC Chunk Size in Bytes: 512 ECC Chunk Count : 4 Payload Size in Bytes : 2048 Auxiliary Size in Bytes: 16 Auxiliary Status Offset: 12 Block Mark Byte Offset : 1999 Block Mark Bit Offset : 0 NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit) ----------------- Boot ROM Geometry ----------------- Boot Area Count : 1 Boot Area Size in Bytes : 4194304 (0x400000) Stride Size in Pages : 64 Search Area Stride Exponent: 2 Scanning device for bad blocks Bad eraseblock 100 at 0x000000c80000 Bad eraseblock 101 at 0x000000ca0000 Boot area protection is enabled. Creating 3 MTD partitions on "gpmi-nfc-main": 0x000000000000-0x000000400000 : "bootloader" 0x000000400000-0x00000fc00000 : "system" 0x00000fc00000-0x000010000000 : "mfg" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "system" UBI: MTD device size: 248 MiB UBI: number of good PEBs: 1982 UBI: number of bad PEBs: 2 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 5 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 1982 UBI: number of PEBs reserved for bad PEB handling: 19 UBI: max/mean erase counter: 80/60 UBI: image sequence number: 1793180392 UBI: background thread "ubi_bgt0d" started, PID 492 ubiblka: unknown partition table ubiblkb: unknown partition table ubiblkc: unknown partition table ubiblkd: unknown partition table ubiblke: unknown partition table PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered PPP MPPE Compression module registered usbcore: registered new interface driver zd1201 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ARC USBOTG Device Controller driver (1 August 2005) mice: PS/2 mouse device common for all mice input: gpio-keys as /devices/platform/gpio-keys.0/input/input0 input: gpio-keys as /devices/platform/gpio-keys.1/input/input1 MXS RTC driver v1.0 hardware v2.3.0 mxs-rtc mxs-rtc.0: rtc core: registered mxs-rtc as rtc0 i2c /dev entries driver bq27000-battery bq27000-battery.0: support ver. 1.2.0 enabled mxs watchdog: initialized, heartbeat 19 sec cpuidle: using governor ladder mxs-mmc: MXS SSP Controller MMC Interface driver mxs-mmc mxs-mmc.0: mmc0: MXS SSP MMC DMAIRQ 82 ERRIRQ 96 Registered led device: led:red:status Registered led device: led:green:status sgtl5000-i2c 0-000a: SGTL5000 revision 17 mmc0: new high speed SDIO card at address 0001 No device for DAI mxs-saif asoc: SGTL5000 <-> mxs-saif mapping ok ALSA device list: #0: mxs-audiodev (SGTL5000) oprofile: hardware counters not available oprofile: using timer interrupt. Netfilter messages via NETLINK v0.30. TCP cubic registered NET: Registered protocol family 17 input: power_button as /devices/virtual/input/input2 kmemleak: Kernel memory leak detector initialized kmemleak: Automatic memory scanning thread started mxs-rtc mxs-rtc.0: setting system clock to 2014-06-16 04:06:38 UTC (1402891598) VFS: Mounted root (squashfs filesystem) readonly on device 254:8. devtmpfs: mounted Freeing init memory: 196K UBI: attaching mtd2 to ubi1 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd2 to ubi1 UBI: MTD device name: "mfg" UBI: MTD device size: 4 MiB UBI: number of good PEBs: 32 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 1 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 32 UBI: number of PEBs reserved for bad PEB handling: 2 UBI: max/mean erase counter: 4/1 UBI: image sequence number: 0 UBI: background thread "ubi_bgt1d" started, PID 594 ubiblkf: unknown partition table UBIFS: mounted UBI device 1, volume 0, name "mfg" UBIFS: mounted read-only UBIFS: file system size: 2031616 bytes (1984 KiB, 1 MiB, 16 LEBs) UBIFS: journal size: 1142785 bytes (1116 KiB, 1 MiB, 8 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: none UBIFS: reserved for root: 0 bytes (0 KiB) UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 5, name "config" UBIFS: file system size: 20697088 bytes (20212 KiB, 19 MiB, 163 LEBs) UBIFS: journal size: 4444160 bytes (4340 KiB, 4 MiB, 35 LEBs) UBIFS: media format: w4/r0 (latest is w4/r0) UBIFS: default compressor: none UBIFS: reserved for root: 0 bytes (0 KiB) UBIFS error (pid 616): ubifs_leb_unmap: unmap LEB -1 failed, error -22 UBIFS warning (pid 616): ubifs_ro_mode: switched to read-only mode, error -22 UBIFS error (pid 616): make_reservation: cannot reserve 160 bytes in jhead 1, error -22 UBIFS error (pid 616): ubifs_write_inode: can't write inode 69, error -22