Re: [tisdk-build-scripts][PATCH 1/2] run-opentest: only pass u-boot and spl/uart when enabled in config

[Denys Dmytriyenko <denys@ti.com>]

On Mon, Sep 08, 2014 at 06:05:02PM -0400, Cooper Jr., Franklin wrote:
> 
> 
> > -----Original Message-----
> > From: Dmytriyenko, Denys
> > Sent: Monday, September 08, 2014 4:43 PM
> > To: Cooper Jr., Franklin
> > Cc: Denys Dmytriyenko; meta-arago@arago-project.org
> > Subject: Re: [meta-arago] [tisdk-build-scripts][PATCH 1/2] run-opentest: only
> > pass u-boot and spl/uart when enabled in config
> > 
> > On Mon, Sep 08, 2014 at 09:39:29PM +0000, Cooper Jr., Franklin wrote:
> > > Should we make this variable specific to am335x some how then?
> > 
> > I don't think there's easy way to control a config variable based on
> > machine...
> [Franklin] Maybe for now just check against the "machine" or some regexp am335x*?
> 
> Also can we update all the configs to use true for now? This way it doesn't 
> change the current behavior. With my above suggestion we can set things to 
> true and take advantage of it when it makes sense.

Actually, I was going to disable it for all my configs, as it makes things 
worse if enabled - don't know why, but systest is not yet explaining this 
behaviour. You can keep it enabled, if you want, in your configs, though.


> > > > -----Original Message-----
> > > > From: meta-arago-bounces@arago-project.org [mailto:meta-arago-
> > > > bounces@arago-project.org] On Behalf Of Denys Dmytriyenko
> > > > Sent: Monday, September 08, 2014 2:49 PM
> > > > To: meta-arago@arago-project.org
> > > > Subject: [meta-arago] [tisdk-build-scripts][PATCH 1/2] run-opentest: only
> > > > pass u-boot and spl/uart when enabled in config
> > > >
> > > > From: Denys Dmytriyenko <denys@ti.com>
> > > >
> > > > Introduce new variable OPENTEST_BOOTLOADERS to control it, but
> > defaults
> > > > to false.
> > > > This never worked as expected, since SPL/UART is only supported by
> > am335x
> > > > and on other platforms it causes OpenTest to miss the escape window
> > and it
> > > > can't stop boot sequence to configure the necessary parameters.
> > > >
> > > > Signed-off-by: Denys Dmytriyenko <denys@ti.com>
> > > > ---
> > > >  configs/arago-core-tisdk-daisy-puget.txt |  4 ++++
> > > >  lib/run-opentest                         | 17 ++++++++++-------
> > > >  2 files changed, 14 insertions(+), 7 deletions(-)
> > > >
> > > > diff --git a/configs/arago-core-tisdk-daisy-puget.txt b/configs/arago-
> > core-
> > > > tisdk-daisy-puget.txt
> > > > index c132baf..f8bfb7a 100644
> > > > --- a/configs/arago-core-tisdk-daisy-puget.txt
> > > > +++ b/configs/arago-core-tisdk-daisy-puget.txt
> > > > @@ -177,6 +177,10 @@ OPENTEST_TEE_IP="none"
> > > >  # Limit the board selection to official TI GT farm, avoiding personal
> > boards
> > > > OPENTEST_HW_CAP="linux_tigt_farm"
> > > >
> > > > +# Determine whether SPL/UART and U-boot binaries are passed to
> > > > OpenTest
> > > > +for # testing. Otherwise uses existing bootloaders on the board (SD,
> > > > +NAND, etc) OPENTEST_BOOTLOADERS="false"
> > > > +
> > > >  # This variable will allow control over whether to perform build testing or
> > #
> > > > skip it.  This should usually be set to true but may be changed for  #
> > > > prototyping.
> > > > diff --git a/lib/run-opentest b/lib/run-opentest index a64e4cc..1a71ae8
> > > > 100644
> > > > --- a/lib/run-opentest
> > > > +++ b/lib/run-opentest
> > > > @@ -206,15 +206,18 @@ run_target_side_test() {
> > > >      fi
> > > >
> > > >      uboot=""
> > > > -    if [ -f $test_dir/temp/board-support/prebuilt-images/u-boot-$m.* ]
> > > > -    then
> > > > -        uboot="~secondary_bootloader=$(ls $test_dir/temp/board-
> > > > support/prebuilt-images/u-boot-$m.*)"
> > > > -    fi
> > > > -
> > > >      spluart=""
> > > > -    if [ -f $test_dir/temp/board-support/prebuilt-images/u-boot-spl.bin-
> > $m ]
> > > > +    if [ "$OPENTEST_BOOTLOADERS" == "true" ]
> > > >      then
> > > > -        spluart="~primary_bootloader=$(ls $test_dir/temp/board-
> > > > support/prebuilt-images/u-boot-spl.bin-$m)"
> > > > +        if [ -f $test_dir/temp/board-support/prebuilt-images/u-boot-$m.* ]
> > > > +        then
> > > > +            uboot="~secondary_bootloader=$(ls $test_dir/temp/board-
> > > > support/prebuilt-images/u-boot-$m.*)"
> > > > +        fi
> > > > +
> > > > +        if [ -f $test_dir/temp/board-support/prebuilt-images/u-boot-
> > spl.bin-$m
> > > > ]
> > > > +        then
> > > > +            spluart="~primary_bootloader=$(ls $test_dir/temp/board-
> > > > support/prebuilt-images/u-boot-spl.bin-$m)"
> > > > +        fi
> > > >      fi
> > > >
> > > >      # Start the STAF process if not already started
> > > > --
> > > > 2.0.4
> > > >
> > > > _______________________________________________
> > > > meta-arago mailing list
> > > > meta-arago@arago-project.org
> > > > http://arago-project.org/cgi-bin/mailman/listinfo/meta-arago
> > > _______________________________________________
> > > meta-arago mailing list
> > > meta-arago@arago-project.org
> > > http://arago-project.org/cgi-bin/mailman/listinfo/meta-arago