Re: [PATCH V3 1/2] i2c-designware: Add i2c bus locking support

["David E. Box" <david.e.box@linux.intel.com>]

On Thu, Dec 04, 2014 at 09:59:11AM +0200, Jarkko Nikula wrote:
> Hi
> 
> On 12/02/2014 02:09 AM, David E. Box wrote:
> >Adds support for acquiring and releasing a hardware bus lock in the i2c
> >designware core transfer function. This is needed for i2c bus controllers
> >that are shared with but not controlled by the kernel.
> >
> >Signed-off-by: David E. Box <david.e.box@linux.intel.com>
> >---
> >  drivers/i2c/busses/i2c-designware-core.c    | 11 +++++++++++
> >  drivers/i2c/busses/i2c-designware-core.h    |  6 ++++++
> >  drivers/i2c/busses/i2c-designware-platdrv.c | 18 +++++++++++++-----
> >  3 files changed, 30 insertions(+), 5 deletions(-)
> >
> ...
> >diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
> >index a743115..afdff3b 100644
> >--- a/drivers/i2c/busses/i2c-designware-platdrv.c
> >+++ b/drivers/i2c/busses/i2c-designware-platdrv.c
> >@@ -261,10 +261,16 @@ static int dw_i2c_probe(struct platform_device *pdev)
> >  		return r;
> >  	}
> >-	pm_runtime_set_autosuspend_delay(&pdev->dev, 1000);
> >-	pm_runtime_use_autosuspend(&pdev->dev);
> >-	pm_runtime_set_active(&pdev->dev);
> >-	pm_runtime_enable(&pdev->dev);
> >+	i2c_dw_eval_lock_support(dev);
> i2c_dw_eval_lock_support() is added in the next patch.
> >+
> >+	if (dev->pm_runtime_disabled) {
> >+		pm_runtime_forbid(&pdev->dev);
> >+	} else {
> >+		pm_runtime_set_autosuspend_delay(&pdev->dev, 1000);
> >+		pm_runtime_use_autosuspend(&pdev);
> >+		pm_runtime_set_active(&pdev->dev);
> >+		pm_runtime_enable(&pdev->dev);
> >+	}
> >  	return 0;
> >  }
> >@@ -314,7 +320,9 @@ static int dw_i2c_resume(struct device *dev)
> >  	struct dw_i2c_dev *i_dev = platform_get_drvdata(pdev);
> >  	clk_prepare_enable(i_dev->clk);
> >-	i2c_dw_init(i_dev);
> >+
> >+	if (!i_dev->pm_runtime_disabled)
> >+		i2c_dw_init(i_dev);
> Should there be similar conditional call or locking around
> i2c_dw_init() and i2c_dw_disable_int() also in dw_i2c_probe()?
> 

Timely reply. Around i2c_dw_init(), yes. I just discovered this as the source
of a recent hang that's occuring in the loop in __i2c_dw_enable().
The hange occurs very infrequently and only, so far, when not built in. A
block around i2c_dw_disable_int() would make sense as well as a precaution.

Dave