From: Gavin Shan <gwshan@linux.vnet.ibm.com>
To: Venkat Duvvuru <VenkatKumar.Duvvuru@Emulex.Com>
Cc: Gavin Shan <gwshan@linux.vnet.ibm.com>,
Ajit Kumar Khaparde <Ajit.Khaparde@Emulex.Com>,
"bhelgaas@google.com" <bhelgaas@google.com>,
"linux-pci@vger.kernel.org" <linux-pci@vger.kernel.org>
Subject: Re: [PATCH] PCI: Mark broken INTx masking for BENET devices
Date: Fri, 9 Jan 2015 11:33:21 +1100 [thread overview]
Message-ID: <20150109003320.GA24054@shangw> (raw)
In-Reply-To: <a227414f-6f4b-4656-b65b-ef8d6e68f135@CMEXHTCAS1.ad.emulex.com>
On Thu, Jan 08, 2015 at 11:33:46AM +0000, Venkat Duvvuru wrote:
>Hi Gavin,
>We tried to reproduce this in our lab but our observation is that we don't see "interrupt storm" in our system.
>Could you please give us the details of the repro scenario?
>
>A few more details will help us understand the problem better as well.
>1. be2net driver version
>2. be2net firmware version
>3. lspci -vvv output of the card (lspci -d 19a2: -vvv)
>4. Is SR-IOV enabled in your card?
>
Venkat, On IBM's Power7 box, I passed through following adpater to guest with following
QEMU command line:
Information from host
=====================
[root@ltcfbl8eb ~]# uname -a
Linux 3.19.0-rc2+ #290 SMP Fri Jan 9 11:20:20 EST 2015 ppc64 ppc64 ppc64 GNU/Linux
[root@ltcfbl8eb ~]# lspci -vvv -s 0000:01:00.0
0000:01:00.0 Ethernet controller: Emulex Corporation OneConnect 10Gb NIC (be3) (rev 02)
Subsystem: Emulex Corporation Device e733
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: Memory at 3ce080100000 (64-bit, non-prefetchable) [size=16K]
Region 2: Memory at 3ce080080000 (64-bit, non-prefetchable) [size=128K]
Region 4: Memory at 3ce0800a0000 (64-bit, non-prefetchable) [size=128K]
[virtual] Expansion ROM at 3ce080000000 [disabled] [size=256K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI-X: Enable+ Count=32 Masked-
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [c0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <16us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
MaxPayload 512 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s L1, Exit Latency L0s <2us, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis+ BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis+, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: Unknown, EnterCompliance- SpeedDis+
Transmit Margin: Normal Operating Range, EnterModifiedCompliance+ ComplianceSOS+
Compliance De-emphasis: -3.5dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [b8] Vital Product Data
Product Name: IBM Flex System EN4054 4-port 10Gb Ethernet Adapter, NIC PF
Read-only fields:
[PN] Part number: 81Y3124
[SN] Serial number: 11S81Y3126Y651HY2B801A
[V0] Vendor specific: FC24495774
[FC] Unknown: 31 37 36 32
[EC] Engineering changes: N28285V
[VI] Vendor specific: 001
[VJ] Vendor specific: 001A
[VL] Vendor specific: 81Y3125
[VM] Vendor specific: 3
[VN] Vendor specific: Y651HY2B801A
[V1] Vendor specific: Emulex 81Y3126 10Gb Ethernet Adapter (Fabric Mezz)
[V2] Vendor specific: 81Y3126
[V4] Vendor specific: 3
[V5] Vendor specific: OCm11104-N-P
[RV] Reserved: checksum good, 124 byte(s) reserved
End
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn+ ChkCap+ ChkEn+
Capabilities: [180 v1] Single Root I/O Virtualization (SR-IOV)
IOVCap: Migration-, Interrupt Message Number: 000
IOVCtl: Enable- Migration- Interrupt- MSE- ARIHierarchy-
IOVSta: Migration-
Initial VFs: 0, Total VFs: 0, Number of VFs: 0, Function Dependency Link: 00
VF offset: 0, stride: 1, Device ID: 0710
Supported Page Size: 00000557, System Page Size: 00000001
Region 0: Memory at 0000000000000000 (64-bit, non-prefetchable)
VF Migration: offset: 00000000, BIR: 0
Capabilities: [160 v1] Alternative Routing-ID Interpretation (ARI)
ARICap: MFVC- ACS-, Next Function: 1
ARICtl: MFVC- ACS-, Function Group: 0
Capabilities: [168 v1] Device Serial Number 00-90-fa-ff-fe-11-fb-b4
Capabilities: [12c v1] Transaction Processing Hints
No steering table available
Kernel driver in use: vfio-pci
Command line to start the guest
===============================
echo 0000:01:00.0 > /sys/bus/pci/drivers/be2net/unbind
echo 0000:01:00.1 > /sys/bus/pci/drivers/be2net/unbind
echo 19a2 0710 > /sys/bus/pci/drivers/vfio-pci/new_id
/home/gavin/qemu/ppc64-softmmu/qemu-system-ppc64 \
-M pseries -m 2048 -enable-kvm -nographic -vga none \
-device spapr-pci-vfio-host-bridge,id=Emulex,iommu=0,index=16 \
-device vfio-pci,host=0000:01:00.0,addr=1.0 \
-device vfio-pci,host=0000:01:00.1,addr=2.0 \
-boot c -hda /home/gavin/images/fc20.img
Information from guest
======================
[root@localhost ~]# cat /etc/issue.net
Fedora release 20 (Heisenbug)
Kernel \r on an \m (\l)
[root@localhost ~]#
[root@localhost ~]# uname -a
Linux localhost.localdomain 3.11.10-301.fc20.ppc64p7 #1 SMP Tue Dec 10 00:35:14 MST 2013 ppc64 ppc64 ppc64 GNU/Linux
[root@localhost ~]#
[root@localhost ~]# lspci
0001:00:01.0 Ethernet controller: Emulex Corporation OneConnect 10Gb NIC (be3) (rev 02)
0001:00:02.0 Ethernet controller: Emulex Corporation OneConnect 10Gb NIC (be3) (rev 02)
[root@localhost ~]# lspci -vvv -s 0001:00:01.0
0001:00:01.0 Ethernet controller: Emulex Corporation OneConnect 10Gb NIC (be3) (rev 02)
Subsystem: Emulex Corporation Device e733
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 17
Region 0: Memory at 200b0000000 (64-bit, non-prefetchable) [size=16K]
Region 2: Memory at 200b0020000 (64-bit, non-prefetchable) [size=128K]
Region 4: Memory at 200b0040000 (64-bit, non-prefetchable) [size=128K]
Expansion ROM at 200b0080000 [disabled] [size=256K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] MSI-X: Enable+ Count=32 Masked-
Vector table: BAR=0 offset=00002000
PBA: BAR=0 offset=00003000
Capabilities: [c0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <16us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- FLReset-
MaxPayload 512 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x8, ASPM L0s L1, Exit Latency L0s <2us, L1 <16us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
ExtSynch- ClockPM- AutWidDis+ BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis+, LTR-, OBFF Disabled
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [b8] Vital Product Data
Product Name: IBM Flex System EN4054 4-port 10Gb Ethernet Adapter, NIC PF
Read-only fields:
[PN] Part number: 81Y3124
[SN] Serial number: 11S81Y3126Y651HY2B801A
[V0] Vendor specific: FC24495774
[FC] Unknown: 31 37 36 32
[EC] Engineering changes: N28285V
[VI] Vendor specific: 001
[VJ] Vendor specific: 001A
[VL] Vendor specific: 81Y3125
[VM] Vendor specific: 3
[VN] Vendor specific: Y651HY2B801A
[V1] Vendor specific: Emulex 81Y3126 10Gb Ethernet Adapter (Fabric Mezz)
[V2] Vendor specific: 81Y3126
[V4] Vendor specific: 3
[V5] Vendor specific: OCm11104-N-P
[RV] Reserved: checksum good, 124 byte(s) reserved
End
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn+ ChkCap+ ChkEn+
Capabilities: [180 v1] Single Root I/O Virtualization (SR-IOV)
IOVCap: Migration-, Interrupt Message Number: 000
IOVCtl: Enable- Migration- Interrupt- MSE- ARIHierarchy-
IOVSta: Migration-
Initial VFs: 0, Total VFs: 0, Number of VFs: 0, Function Dependency Link: 00
VF offset: 0, stride: 1, Device ID: 0710
Supported Page Size: 00000557, System Page Size: 00000001
Region 0: Memory at 0000000000000000 (64-bit, non-prefetchable)
VF Migration: offset: 00000000, BIR: 0
Capabilities: [160 v1] Alternative Routing-ID Interpretation (ARI)
ARICap: MFVC- ACS-, Next Function: 1
ARICtl: MFVC- ACS-, Function Group: 0
Capabilities: [168 v1] Device Serial Number 00-90-fa-ff-fe-11-fb-b4
Capabilities: [12c v1] Transaction Processing Hints
No steering table available
Kernel driver in use: be2net
[root@localhost ~]# ethtool -i enP1p0s1
driver: be2net
version: 4.6.62.0u
firmware-version: 4.1.422.0
bus-info: 0001:00:01.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: no
Steps to recreate the issue
===========================
1. Configure the NIC and ping it from external.
2. Inject EEH error by running following command in host side. After about
20 seconds, I got following message from host side. With the patch applied
to host kernel, I didn't see the warning messages:
host# echo 1:0:0:0:0:0 > /sys/kernel/debug/powerpc/PCI0000/err_injct
:
[ 419.083164] P7IOC PHB#0 Diag-data (Version: 1)
[ 419.083229] brdgCtl: 00000002
[ 419.083300] UtlSts: 00000000 40000000 00000000
[ 419.083347] RootSts: 0000004f 016003c0 a0820008 40100147 00004000
[ 419.083404] RootErrSts: 00000024 00000000 00000000
[ 419.083451] RootErrLog1: 00010000 0000000000000000 0000000000000000
[ 419.083508] PhbSts: 0000001c00000000 0000001c00000000
[ 419.083555] Lem: 0200000000000004 1249a1147f500f2c 0000000000000000
[ 419.083613] PhbErr: 0000000020000000 0000000020000000 0000000000000000 000002b0f8000000
[ 419.083692] OutErr: 0200000000000000 0200000000000000 1204ce7000443ce0 800a012000000000
[ 419.083772] PE[ 1] A/B: 8720003d01000000 8000000000000000
[ 419.249183] irq 17: nobody cared (try booting with the "irqpoll" option)
[ 419.249252] CPU: 44 PID: 2488 Comm: qemu-system-ppc Not tainted 3.19.0-rc2+ #290
[ 419.249259] Call Trace:
[ 419.249268] [c000000f2ee63ae0] [c0000000008360d0] .dump_stack+0x88/0xa8 (unreliable)
[ 419.249280] [c000000f2ee63b60] [c0000000000d7e80] .__report_bad_irq+0x44/0x104
[ 419.249288] [c000000f2ee63c10] [c0000000000d848c] .note_interrupt+0x24c/0x304
[ 419.249359] [c000000f2ee63cc0] [c0000000000d56d4] .handle_irq_event_percpu+0x1c4/0x220
[ 419.249439] [c000000f2ee63d90] [c0000000000d579c] .handle_irq_event+0x6c/0x98
[ 419.249509] [c000000f2ee63e10] [c0000000000d9418] .handle_fasteoi_irq+0xc4/0x184
[ 419.249589] [c000000f2ee63e90] [c0000000000d4ad4] .generic_handle_irq+0x48/0x60
[ 419.249671] [c000000f2ee63f10] [c00000000000eeac] .__do_irq+0xcc/0x168
[ 419.249741] [c000000f2ee63f90] [c00000000001c7d8] .call_do_irq+0x14/0x24
[ 419.249811] [c0000007f35ef2f0] [c00000000000efd4] .do_IRQ+0x8c/0xc8
[ 419.249881] [c0000007f35ef3a0] [c0000000000022b0] hardware_interrupt_common+0x130/0x180
[ 419.249964] --- interrupt: 501 at .__kvmppc_vcore_entry+0x13c/0x1a0
LR = kvmppc_call_hv_entry+0x8/0x118
[ 419.250056] [c0000007f35ef690] [c00000000007080c] .__kvmppc_vcore_entry+0x13c/0x1a0 (unreliable)
[ 419.250149] [c0000007f35ef860] [c00000000006fd30] .kvmppc_vcpu_run_hv+0xa68/0x1408
[ 419.250230] [c0000007f35ef9f0] [c0000000000682e0] .kvmppc_vcpu_run+0x44/0x58
[ 419.250300] [c0000007f35efa70] [c0000000000662cc] .kvm_arch_vcpu_ioctl_run+0xfc/0x130
[ 419.250382] [c0000007f35efb00] [c00000000005fb18] .kvm_vcpu_ioctl+0x1a8/0x5f4
[ 419.250452] [c0000007f35efcb0] [c0000000001e8e98] .do_vfs_ioctl+0x618/0x69c
[ 419.250521] [c0000007f35efd90] [c0000000001e8f8c] .SyS_ioctl+0x70/0x9c
[ 419.250592] [c0000007f35efe30] [c000000000009198] syscall_exit+0x0/0x98
[ 419.250661] handlers:
[ 419.250687] [<c000000001586560>] .vfio_intx_handler
[ 419.250744] Disabling IRQ #17
[ 419.422125] irq 18: nobody cared (try booting with the "irqpoll" option)
[ 419.422208] CPU: 24 PID: 2488 Comm: qemu-system-ppc Not tainted 3.19.0-rc2+ #290
[ 419.422215] Call Trace:
[ 419.422221] [c000000f2ef03ae0] [c0000000008360d0] .dump_stack+0x88/0xa8 (unreliable)
[ 419.422243] [c000000f2ef03b60] [c0000000000d7e80] .__report_bad_irq+0x44/0x104
[ 419.422324] [c000000f2ef03c10] [c0000000000d848c] .note_interrupt+0x24c/0x304
[ 419.422393] [c000000f2ef03cc0] [c0000000000d56d4] .handle_irq_event_percpu+0x1c4/0x220
[ 419.422475] [c000000f2ef03d90] [c0000000000d579c] .handle_irq_event+0x6c/0x98
[ 419.422545] [c000000f2ef03e10] [c0000000000d9418] .handle_fasteoi_irq+0xc4/0x184
[ 419.422628] [c000000f2ef03e90] [c0000000000d4ad4] .generic_handle_irq+0x48/0x60
[ 419.422710] [c000000f2ef03f10] [c00000000000eeac] .__do_irq+0xcc/0x168
[ 419.422780] [c000000f2ef03f90] [c00000000001c7d8] .call_do_irq+0x14/0x24
[ 419.422849] [c0000007f35ef450] [c00000000000efd4] .do_IRQ+0x8c/0xc8
[ 419.422919] [c0000007f35ef500] [c0000000000022b0] hardware_interrupt_common+0x130/0x180
[ 419.423000] --- interrupt: 501 at .arch_local_irq_restore+0x54/0x78
LR = .arch_local_irq_restore+0x54/0x78
[ 419.423105] [c0000007f35ef7f0] [c0000007f35ef890] 0xc0000007f35ef890 (unreliable)
[ 419.423186] [c0000007f35ef860] [c00000000006fce4] .kvmppc_vcpu_run_hv+0xa1c/0x1408
[ 419.423267] [c0000007f35ef9f0] [c0000000000682e0] .kvmppc_vcpu_run+0x44/0x58
[ 419.423336] [c0000007f35efa70] [c0000000000662cc] .kvm_arch_vcpu_ioctl_run+0xfc/0x130
[ 419.423416] [c0000007f35efb00] [c00000000005fb18] .kvm_vcpu_ioctl+0x1a8/0x5f4
[ 419.423486] [c0000007f35efcb0] [c0000000001e8e98] .do_vfs_ioctl+0x618/0x69c
[ 419.423555] [c0000007f35efd90] [c0000000001e8f8c] .SyS_ioctl+0x70/0x9c
[ 419.423625] [c0000007f35efe30] [c000000000009198] syscall_exit+0x0/0x98
[ 419.423693] handlers:
[ 419.423720] [<c000000001586560>] .vfio_intx_handler
[ 419.423778] Disabling IRQ #18
Thanks,
Gavin
>> -----Original Message-----
>> From: linux-pci-owner@vger.kernel.org [mailto:linux-pci-
>> owner@vger.kernel.org] On Behalf Of Gavin Shan
>> Sent: Monday, January 05, 2015 7:48 AM
>> To: linux-pci@vger.kernel.org
>> Cc: Ajit Kumar Khaparde; bhelgaas@google.com; Gavin Shan
>> Subject: [PATCH] PCI: Mark broken INTx masking for BENET devices
>>
>> Similar to commit 11e4253 ("PCI: Assume all Mellanox devices have
>> broken INTx masking"), when passing through following PCI device
>> using VFIO infrastructure, interrupt storm are reported. After
>> marking its INTx masking is broken, the interrupt storm isn't
>> raised again:
>>
>> # lspci -s 0000::.
>> 0000:01:00.0 Ethernet controller: Emulex Corporation \
>> OneConnect 10Gb NIC (be3) (rev 02)
>> 0000:01:00.1 Ethernet controller: Emulex Corporation \
>> OneConnect 10Gb NIC (be3) (rev 02)
>> # lspci -n -s 0000::.
>> 0000:01:00.0 0200: 19a2:0710 (rev 02)
>> 0000:01:00.1 0200: 19a2:0710 (rev 02)
>>
>> Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
>> ---
>> drivers/pci/quirks.c | 2 ++
>> include/linux/pci_ids.h | 2 ++
>> 2 files changed, 4 insertions(+)
>>
>> diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
>> index ed6f89b..e823ac0 100644
>> --- a/drivers/pci/quirks.c
>> +++ b/drivers/pci/quirks.c
>> @@ -3027,6 +3027,8 @@
>> DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_REALTEK, 0x8169,
>> quirk_broken_intx_masking);
>> DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MELLANOX, PCI_ANY_ID,
>> quirk_broken_intx_masking);
>> +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_BE, PCI_ANY_ID,
>> + quirk_broken_intx_masking);
>>
>> #ifdef CONFIG_ACPI
>> /*
>> diff --git a/include/linux/pci_ids.h b/include/linux/pci_ids.h
>> index e63c02a..df70b76 100644
>> --- a/include/linux/pci_ids.h
>> +++ b/include/linux/pci_ids.h
>> @@ -2481,6 +2481,8 @@
>> #define PCI_DEVICE_ID_KORENIX_JETCARDF2 0x1700
>> #define PCI_DEVICE_ID_KORENIX_JETCARDF3 0x17ff
>>
>> +#define PCI_VENDOR_ID_BE 0x19a2
>> +
>> #define PCI_VENDOR_ID_QMI 0x1a32
>>
>> #define PCI_VENDOR_ID_AZWAVE 0x1a3b
>> --
>> 1.8.3.2
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-pci" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
next prev parent reply other threads:[~2015-01-09 0:33 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-01-05 2:17 [PATCH] PCI: Mark broken INTx masking for BENET devices Gavin Shan
2015-01-07 4:29 ` Venkat Duvvuru
2015-01-07 14:57 ` Alex Williamson
2015-01-08 11:33 ` Venkat Duvvuru
2015-01-09 0:33 ` Gavin Shan [this message]
2015-01-09 1:25 ` Alex Williamson
2015-01-09 7:40 ` Venkat Duvvuru
2015-01-11 22:20 ` Gavin Shan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150109003320.GA24054@shangw \
--to=gwshan@linux.vnet.ibm.com \
--cc=Ajit.Khaparde@Emulex.Com \
--cc=VenkatKumar.Duvvuru@Emulex.Com \
--cc=bhelgaas@google.com \
--cc=linux-pci@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.