From: Simon Horman <horms@verge.net.au>
To: linux-sh@vger.kernel.org
Subject: Re: [PATCH 2/2] usb: renesas_usbhs: add support for requesting DT DMA
Date: Thu, 29 Jan 2015 12:19:09 +0000 [thread overview]
Message-ID: <20150129121909.GA11832@verge.net.au> (raw)
In-Reply-To: <4F05318F.9060209@renesas.com>
Hi Shimoda-san,
On Mon, Jan 19, 2015 at 12:53:17PM +0900, Yoshihiro Shimoda wrote:
> This patch adds dma_request_slave_channel_reason() calling to request
> dma slave channels for multiplatform environment.
>
> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
> ---
> .../devicetree/bindings/usb/renesas_usbhs.txt | 2 ++
> drivers/usb/renesas_usbhs/fifo.c | 11 ++++++++++-
> 2 files changed, 12 insertions(+), 1 deletion(-)
I have observed what appears to be a regression caused by this
patch when booting a kernel built using shmobile_defconfig on the koelsch
and lager boards.
I noticed this problem while testing next-20150129.
I have provided boot logs at the end of this email.
>
> diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
> index b08c903..61b045b 100644
> --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
> +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt
> @@ -14,6 +14,8 @@ Optional properties:
> function should be enabled
> - phys: phandle + phy specifier pair
> - phy-names: must be "usb"
> + - dmas: Must contain a list of references to DMA specifiers.
> + - dma-names : Must contain a list of DMA names, "tx" or "rx".
>
> Example:
> usbhs: usb@e6590000 {
> diff --git a/drivers/usb/renesas_usbhs/fifo.c b/drivers/usb/renesas_usbhs/fifo.c
> index 48e31b9..4c086b1 100644
> --- a/drivers/usb/renesas_usbhs/fifo.c
> +++ b/drivers/usb/renesas_usbhs/fifo.c
> @@ -1069,12 +1069,21 @@ static void usbhsf_dma_init_pdev(struct usbhs_fifo *fifo)
> &fifo->rx_slave);
> }
>
> +static void usbhsf_dma_init_dt(struct device *dev, struct usbhs_fifo *fifo)
> +{
> + fifo->tx_chan = dma_request_slave_channel_reason(dev, "tx");
> + fifo->rx_chan = dma_request_slave_channel_reason(dev, "rx");
> +}
> +
> static void usbhsf_dma_init(struct usbhs_priv *priv,
> struct usbhs_fifo *fifo)
> {
> struct device *dev = usbhs_priv_to_dev(priv);
>
> - usbhsf_dma_init_pdev(fifo);
> + if (dev->of_node)
> + usbhsf_dma_init_dt(dev, fifo);
> + else
> + usbhsf_dma_init_pdev(fifo);
>
> if (fifo->tx_chan || fifo->rx_chan)
> dev_dbg(dev, "enable DMAEngine (%s%s%s)\n",
Koelsch
-------
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 3.19.0-rc5-00129-gabd2dbf (horms@ayumi.isobedori.kobe.vergenet.net) (gcc version 4.6.3 (GCC) ) #959 SMP Thu Jan 29 20:40:07 JST 2015
CPU: ARMv7 Processor [413fc0f2] revision 2 (ARMv7), cr\x10c5307d
CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
Machine model: Koelsch
Ignoring memory block 0x200000000 - 0x240000000
debug: ignoring loglevel setting.
Memory policy: Data cache writealloc
On node 0 totalpages: 262144
free_area_init_node: node 0, pgdat c0612a80, node_mem_map eeff9000
Normal zone: 1520 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 194560 pages, LIFO batch:31
HighMem zone: 67584 pages, LIFO batch:15
PERCPU: Embedded 7 pages/cpu @eefca000 s7552 r0 d21120 u32768
pcpu-alloc: s7552 r0 d21120 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624
Kernel command line: ignore_loglevel rw root=/dev/nfs ip=dhcp
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1032964K/1048576K available (4524K kernel code, 264K rwdata, 1128K rodata, 268K init, 191K bss, 15612K reserved, 0K cma-reserved, 270336K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
.text : 0xc0008000 - 0xc058e024 (5657 kB)
.init : 0xc058f000 - 0xc05d2000 ( 268 kB)
.data : 0xc05d2000 - 0xc06143a0 ( 265 kB)
.bss : 0xc06143a0 - 0xc064407c ( 192 kB)
Hierarchical RCU implementation.
RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf\x16, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
Architected cp15 timer(s) running at 10.00MHz (virt).
sched_clock: 56 bits at 10MHz, resolution 100ns, wraps every 3435973836800ns
Switching to timer-based delay loop, resolution 100ns
Console: colour dummy device 80x30
console [tty0] enabled
Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj\x100000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
CPU: Testing write buffer coherency: ok
CPU0: update cpu_capacity 1024
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x40471350 - 0x404713a8
Unable to boot CPU1 when MD21 is set
CPU1: failed to boot: -524
Brought up 1 CPUs
SMP: Total of 1 processors activated (20.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
renesas_irqc e61c0000.interrupt-controller: driving 10 irqs
sh-pfc e6060000.pfc: r8a77910_pfc support registered
No ATAGs?
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
platform regulator@0: Driver reg-fixed-voltage requests probe deferral
platform regulator@2: Driver reg-fixed-voltage requests probe deferral
platform regulator@4: Driver reg-fixed-voltage requests probe deferral
gpio-regulator regulator@1: Could not obtain regulator setting GPIOs: -517
platform regulator@1: Driver gpio-regulator requests probe deferral
gpio-regulator regulator@3: Could not obtain regulator setting GPIOs: -517
platform regulator@3: Driver gpio-regulator requests probe deferral
gpio-regulator regulator@5: Could not obtain regulator setting GPIOs: -517
platform regulator@5: Driver gpio-regulator requests probe deferral
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-sh_mobile e60b0000.i2c: I2C adapter 6, bus speed 100000 Hz
media: Linux media interface: v0.10
Linux video capture interface: v2.00
sh_cmt ffca0000.timer: ch0: used for clock events
sh_cmt ffca0000.timer: ch1: used as clock source
Advanced Linux Sound Architecture Driver Initialized.
Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
futex hash table entries: 512 (order: 3, 32768 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
nfs4filelayout_init: NFSv4 File Layout Driver Registering...
bounce: pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
gpio_rcar e6050000.gpio: driving 32 GPIOs
gpio_rcar e6051000.gpio: driving 32 GPIOs
gpio_rcar e6052000.gpio: driving 32 GPIOs
gpio_rcar e6053000.gpio: driving 32 GPIOs
gpio_rcar e6054000.gpio: driving 32 GPIOs
gpio_rcar e6055000.gpio: driving 32 GPIOs
gpio_rcar e6055400.gpio: driving 32 GPIOs
gpio_rcar e6055800.gpio: driving 26 GPIOs
pci-rcar-gen2 ee090000.pci: PCI: bus0 revision 11
pci-rcar-gen2 ee090000.pci: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0xee080000-0xee0810ff]
pci_bus 0000:00: root bus resource [mem 0xee080000-0xee0810ff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:00.0: [1033:0000] type 00 class 0x060000
pci 0000:00:00.0: reg 0x10: [mem 0xee090800-0xee090bff]
pci 0000:00:00.0: reg 0x14: [mem 0x40000000-0x7fffffff pref]
pci 0000:00:01.0: [1033:0035] type 00 class 0x0c0310
pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x00000fff]
pci 0000:00:01.0: supports D1 D2
pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:02.0: [1033:00e0] type 00 class 0x0c0320
pci 0000:00:02.0: reg 0x10: [mem 0x00000000-0x000000ff]
pci 0000:00:02.0: supports D1 D2
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot
PCI: bus0: Fast back to back transfers disabled
pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
pci 0000:00:01.0: can't enable device: BAR 0 [mem 0x00000000-0x00000fff] not claimed
pci 0000:00:01.0: Can't enable PCI device, BIOS handoff failed.
pci 0000:00:02.0: can't enable device: BAR 0 [mem 0x00000000-0x000000ff] not claimed
pci 0000:00:02.0: Can't enable PCI device, BIOS handoff failed.
pci 0000:00:01.0: BAR 0: assigned [mem 0xee080000-0xee080fff]
pci 0000:00:02.0: BAR 0: assigned [mem 0xee081000-0xee0810ff]
pci-rcar-gen2 ee0d0000.pci: PCI: bus0 revision 11
pci-rcar-gen2 ee0d0000.pci: PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [io 0xee0c0000-0xee0c10ff]
pci_bus 0000:01: root bus resource [mem 0xee0c0000-0xee0c10ff]
pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
pci 0000:01:00.0: [1033:0000] type 00 class 0x060000
pci 0000:01:00.0: reg 0x10: [mem 0xee0d0800-0xee0d0bff]
pci 0000:01:00.0: reg 0x14: [mem 0x40000000-0x7fffffff pref]
pci 0000:01:01.0: [1033:0035] type 00 class 0x0c0310
pci 0000:01:01.0: reg 0x10: [mem 0x00000000-0x00000fff]
pci 0000:01:01.0: supports D1 D2
pci 0000:01:01.0: PME# supported from D0 D1 D2 D3hot
pci 0000:01:02.0: [1033:00e0] type 00 class 0x0c0320
pci 0000:01:02.0: reg 0x10: [mem 0x00000000-0x000000ff]
pci 0000:01:02.0: supports D1 D2
pci 0000:01:02.0: PME# supported from D0 D1 D2 D3hot
PCI: bus1: Fast back to back transfers disabled
pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
pci 0000:01:01.0: can't enable device: BAR 0 [mem 0x00000000-0x00000fff] not claimed
pci 0000:01:01.0: Can't enable PCI device, BIOS handoff failed.
pci 0000:01:02.0: can't enable device: BAR 0 [mem 0x00000000-0x000000ff] not claimed
pci 0000:01:02.0: Can't enable PCI device, BIOS handoff failed.
pci 0000:01:01.0: BAR 0: assigned [mem 0xee0c0000-0xee0c0fff]
pci 0000:01:02.0: BAR 0: assigned [mem 0xee0c1000-0xee0c10ff]
rcar-pcie fe000000.pcie: PCIe link down
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
SuperH (H)SCI(F) driver initialized
e6e60000.serial: ttySC6 at MMIO 0xe6e60000 (irq = 107, base_baud = 0) is a scif
console [ttySC6] enabled
e6e68000.serial: ttySC7 at MMIO 0xe6e68000 (irq = 108, base_baud = 0) is a scif
[drm] Initialized drm 1.1.0 20060810
rcar-du feb00000.display: Failed to initialize drm fb helper.
rcar-du feb00000.display: failed to initialize DRM/KMS
rcar-du: probe of feb00000.display failed with error -22
scsi host0: sata_rcar
ata1: SATA max UDMA/133 irq 110
renesas_spi e6b10000.spi: dma_request_slave_channel_compat failed
renesas_spi e6b10000.spi: DMA not available, using PIO
m25p80 spi0.0: s25fl512s (65536 Kbytes)
3 ofpart partitions found on MTD device spi0.0
Creating 3 MTD partitions on "spi0.0":
0x000000000000-0x000000080000 : "loader"
0x000000080000-0x000000100000 : "bootenv"
0x000000100000-0x000004000000 : "data"
renesas_spi e6b10000.spi: probed
spi_sh_msiof e6e20000.spi: dma_request_slave_channel_compat failed
spi_sh_msiof e6e20000.spi: DMA not available, using PIO
libphy: sh_mii: probed
sh-eth ee700000.ethernet eth0: Base address at 0xee700000, 2e:09:0a:00:6d:00, IRQ 109.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:02.0: enabling device (0140 -> 0142)
ehci-pci 0000:00:02.0: EHCI Host Controller
ehci-pci 0000:00:02.0: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:02.0: irq 120, io mem 0xee081000
ehci-pci 0000:00:02.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci-pci 0000:01:02.0: enabling device (0140 -> 0142)
ehci-pci 0000:01:02.0: EHCI Host Controller
ehci-pci 0000:01:02.0: new USB bus registered, assigned bus number 2
ehci-pci 0000:01:02.0: irq 121, io mem 0xee0c1000
ehci-pci 0000:01:02.0: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-pci 0000:00:01.0: enabling device (0140 -> 0142)
ohci-pci 0000:00:01.0: OHCI PCI host controller
ohci-pci 0000:00:01.0: new USB bus registered, assigned bus number 3
ohci-pci 0000:00:01.0: irq 120, io mem 0xee080000
ohci-pci 0000:00:01.0: init err (00002edf 0000)
ohci-pci 0000:00:01.0: can't start
ohci-pci 0000:00:01.0: startup error -75
ohci-pci 0000:00:01.0: USB bus 3 deregistered
ohci-pci 0000:00:01.0: init 0000:00:01.0 fail, -75
ohci-pci: probe of 0000:00:01.0 failed with error -75
ohci-pci 0000:01:01.0: enabling device (0140 -> 0142)
ohci-pci 0000:01:01.0: OHCI PCI host controller
ohci-pci 0000:01:01.0: new USB bus registered, assigned bus number 3
ohci-pci 0000:01:01.0: irq 121, io mem 0xee0c0000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
sh-pfc e6060000.pfc: pin GP_7_23 already requested by ee090000.pci; cannot claim for e6590000.usb
sh-pfc e6060000.pfc: pin-247 (e6590000.usb) status -22
sh-pfc e6060000.pfc: could not request pin 247 (GP_7_23) from group usb0 on device sh-pfc
renesas_usbhs e6590000.usb: Error applying setting, reverse things back
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
renesas_usbhs e6590000.usb: gadget probed
renesas_usbhs e6590000.usb: platform init failed.
ata1: link resume succeeded after 1 retries
Unable to handle kernel NULL pointer dereference at virtual address 0000000d
pgd = c0004000
[0000000d] *pgd\0000000
Internal error: Oops: 5 [#1] SMP ARM
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc5-00129-gabd2dbf #959
Hardware name: Generic R8A7791 (Flattened Device Tree)
task: ee84bb40 ti: ee84c000 task.ti: ee84c000
PC is at dma_release_channel+0x18/0xbc
LR is at dma_release_channel+0x18/0xbc
pc : [<c01e7fe8>] lr : [<c01e7fe8>] psr: 60000113
sp : ee84dd78 ip : ee84dd78 fp : ee84dd8c
r10: c058f5d4 r9 : c05ce67c r8 : 00000024
r7 : ee303010 r6 : 00000000 r5 : ee303100 r4 : ffffffed
r3 : 00000003 r2 : ee84dd60 r1 : 0002e30a r0 : c05f8e90
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5307d Table: 4000406a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xee84c238)
Stack: (0xee84dd78 to 0xee84e000)
dd60: 00000000 ee303100
dd80: ee84ddb4 ee84dd90 c02d06c0 c01e7fdc 00000003 ee303010 ee949600 ffffffed
dda0: ee949610 00000000 ee84dde4 ee84ddb8 c02cd524 c02d069c ee949618 00000004
ddc0: ee949610 ffffffed ee949610 c0605bd0 c0605bd0 c05c4c78 ee84de04 ee84dde8
dde0: c024b54c c02cd1a8 c024b4fc ee949610 00000000 00000000 ee84de24 ee84de08
de00: c024a010 c024b508 ee949610 ee949644 c0605bd0 00000000 ee84de44 ee84de28
de20: c024a1c4 c0249f4c c024a15c c0605bd0 ee84de48 c024a15c ee84de6c ee84de48
de40: c024895c c024a168 ee82db5c ee8f3834 c0605bd0 eeb31a00 c0600d78 00000000
de60: ee84de7c ee84de70 c024a2e0 c024890c ee84dea4 ee84de80 c02490ec c024a2cc
de80: c056d039 ee84de90 c0605bd0 ee307300 00000000 c05c4c78 ee84debc ee84dea8
dea0: c024a9f0 c0249044 c05ab770 ee307300 ee84decc ee84dec0 c024bdb4 c024a958
dec0: ee84dedc ee84ded0 c05ab788 c024bd70 ee84df54 ee84dee0 c058fdc8 c05ab77c
dee0: 60000153 ef7fcce1 ee84df0c ee84def8 c058f500 c01a9c94 c058f5d4 c056e1da
df00: ee84df54 ee84df10 c003c47c c058f5e0 ef7fcce8 00000006 00000006 000000aa
df20: c058c0e8 00000000 ee84df54 00000006 00000006 c05c54d0 c05c54b0 c06143c0
df40: 000000aa c05ce67c ee84df94 ee84df58 c058ff84 c058fccc 00000006 00000006
df60: c058f5d4 78f7f1ef ffffffff 00000000 c0469290 00000000 00000000 00000000
df80: 00000000 00000000 ee84dfac ee84df98 c04692a0 c058fe84 ee84c000 00000000
dfa0: 00000000 ee84dfb0 c000ebf8 c046929c 00000000 00000000 00000000 00000000
dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 9d5cdd68 bead4f78
Backtrace:
[<c01e7fd0>] (dma_release_channel) from [<c02d06c0>] (usbhs_fifo_remove+0x30/0x60)
r5:ee303100 r4:00000000
[<c02d0690>] (usbhs_fifo_remove) from [<c02cd524>] (usbhs_probe+0x388/0x3f0)
r8:00000000 r7:ee949610 r6:ffffffed r5:ee949600 r4:ee303010 r3:00000003
[<c02cd19c>] (usbhs_probe) from [<c024b54c>] (platform_drv_probe+0x50/0x98)
r8:c05c4c78 r7:c0605bd0 r6:c0605bd0 r5:ee949610 r4:ffffffed
[<c024b4fc>] (platform_drv_probe) from [<c024a010>] (driver_probe_device+0xd0/0x21c)
r6:00000000 r5:00000000 r4:ee949610 r3:c024b4fc
[<c0249f40>] (driver_probe_device) from [<c024a1c4>] (__driver_attach+0x68/0x8c)
r7:00000000 r6:c0605bd0 r5:ee949644 r4:ee949610
[<c024a15c>] (__driver_attach) from [<c024895c>] (bus_for_each_dev+0x5c/0x94)
r6:c024a15c r5:ee84de48 r4:c0605bd0 r3:c024a15c
[<c0248900>] (bus_for_each_dev) from [<c024a2e0>] (driver_attach+0x20/0x28)
r7:00000000 r6:c0600d78 r5:eeb31a00 r4:c0605bd0
[<c024a2c0>] (driver_attach) from [<c02490ec>] (bus_add_driver+0xb4/0x1bc)
[<c0249038>] (bus_add_driver) from [<c024a9f0>] (driver_register+0xa4/0xe8)
r7:c05c4c78 r6:00000000 r5:ee307300 r4:c0605bd0
[<c024a94c>] (driver_register) from [<c024bdb4>] (__platform_driver_register+0x50/0x64)
r5:ee307300 r4:c05ab770
[<c024bd64>] (__platform_driver_register) from [<c05ab788>] (renesas_usbhs_driver_init+0x18/0x20)
[<c05ab770>] (renesas_usbhs_driver_init) from [<c058fdc8>] (do_one_initcall+0x108/0x1b8)
[<c058fcc0>] (do_one_initcall) from [<c058ff84>] (kernel_init_freeable+0x10c/0x1d8)
r9:c05ce67c r8:000000aa r7:c06143c0 r6:c05c54b0 r5:c05c54d0 r4:00000006
[<c058fe78>] (kernel_init_freeable) from [<c04692a0>] (kernel_init+0x10/0xec)
r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0469290
r4:00000000
[<c0469290>] (kernel_init) from [<c000ebf8>] (ret_from_fork+0x14/0x3c)
r4:00000000 r3:ee84c000
Code: e24cb004 e1a04000 e59f0094 eb0a1caa (e5943020)
---[ end trace c4f5636aa673cc02 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Lager
-----
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 3.19.0-rc5-00129-gabd2dbf (horms@ayumi.isobedori.kobe.vergenet.net) (gcc version 4.6.3 (GCC) ) #961 SMP Thu Jan 29 20:46:17 JST 2015
CPU: ARMv7 Processor [413fc0f2] revision 2 (ARMv7), cr\x10c5307d
CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
Machine model: Lager
Ignoring memory block 0x140000000 - 0x200000000
debug: ignoring loglevel setting.
Memory policy: Data cache writealloc
On node 0 totalpages: 262144
free_area_init_node: node 0, pgdat c0612a80, node_mem_map eeff9000
Normal zone: 1520 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 194560 pages, LIFO batch:31
HighMem zone: 67584 pages, LIFO batch:15
PERCPU: Embedded 7 pages/cpu @eef9a000 s7552 r0 d21120 u32768
pcpu-alloc: s7552 r0 d21120 u32768 alloc=8*4096
pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624
Kernel command line: console=ttySC6,115200 ignore_loglevel rw root=/dev/nfs ip=dhcp
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1032784K/1048576K available (4524K kernel code, 264K rwdata, 1128K rodata, 268K init, 191K bss, 15792K reserved, 0K cma-reserved, 270336K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
.text : 0xc0008000 - 0xc058e024 (5657 kB)
.init : 0xc058f000 - 0xc05d2000 ( 268 kB)
.data : 0xc05d2000 - 0xc06143a0 ( 265 kB)
.bss : 0xc06143a0 - 0xc064407c ( 192 kB)
Hierarchical RCU implementation.
NR_IRQS:16 nr_irqs:16 16
Architected cp15 timer(s) running at 10.00MHz (virt).
sched_clock: 56 bits at 10MHz, resolution 100ns, wraps every 3435973836800ns
Switching to timer-based delay loop, resolution 100ns
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 20.00 BogoMIPS (lpj\x100000)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
CPU: Testing write buffer coherency: ok
CPU0: update cpu_capacity 1535
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x40471350 - 0x404713a8
CPU1: update cpu_capacity 1535
CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
CPU2: update cpu_capacity 1535
CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
CPU3: update cpu_capacity 1535
CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
CPU4: failed to boot: -22
CPU5: failed to boot: -22
CPU6: failed to boot: -22
CPU7: failed to boot: -22
Brought up 4 CPUs
SMP: Total of 4 processors activated (80.00 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
renesas_irqc e61c0000.interrupt-controller: driving 4 irqs
sh-pfc e6060000.pfc: r8a77900_pfc support registered
No ATAGs?
hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 8 bytes.
platform regulator@1: Driver reg-fixed-voltage requests probe deferral
platform regulator@3: Driver reg-fixed-voltage requests probe deferral
gpio-regulator regulator@2: Could not obtain regulator setting GPIOs: -517
platform regulator@2: Driver gpio-regulator requests probe deferral
gpio-regulator regulator@4: Could not obtain regulator setting GPIOs: -517
platform regulator@4: Driver gpio-regulator requests probe deferral
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-sh_mobile e6500000.i2c: I2C adapter 4, bus speed 100000 Hz
i2c-sh_mobile e6510000.i2c: I2C adapter 5, bus speed 100000 Hz
i2c-sh_mobile e6520000.i2c: I2C adapter 6, bus speed 100000 Hz
i2c-sh_mobile e60b0000.i2c: I2C adapter 7, bus speed 100000 Hz
media: Linux media interface: v0.10
Linux video capture interface: v2.00
sh_cmt ffca0000.timer: ch0: used for clock events
sh_cmt ffca0000.timer: ch1: used as clock source
Advanced Linux Sound Architecture Driver Initialized.
Switched to clocksource arch_sys_counter
NET: Registered protocol family 2
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP: reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
futex hash table entries: 2048 (order: 5, 131072 bytes)
NFS: Registering the id_resolver key type
Key type id_resolver registered
Key type id_legacy registered
nfs4filelayout_init: NFSv4 File Layout Driver Registering...
bounce: pool size: 64 pages
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
gpio_rcar e6050000.gpio: driving 32 GPIOs
gpio_rcar e6051000.gpio: driving 32 GPIOs
gpio_rcar e6052000.gpio: driving 32 GPIOs
gpio_rcar e6053000.gpio: driving 32 GPIOs
gpio_rcar e6054000.gpio: driving 32 GPIOs
gpio_rcar e6055000.gpio: driving 32 GPIOs
pci-rcar-gen2 ee090000.pci: PCI: bus0 revision 11
pci-rcar-gen2 ee090000.pci: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0xee080000-0xee0810ff]
pci_bus 0000:00: root bus resource [mem 0xee080000-0xee0810ff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
pci 0000:00:00.0: [1033:0000] type 00 class 0x060000
pci 0000:00:00.0: reg 0x10: [mem 0xee090800-0xee090bff]
pci 0000:00:00.0: reg 0x14: [mem 0x40000000-0x7fffffff pref]
pci 0000:00:01.0: [1033:0035] type 00 class 0x0c0310
pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x00000fff]
pci 0000:00:01.0: supports D1 D2
pci 0000:00:01.0: PME# supported from D0 D1 D2 D3hot
pci 0000:00:02.0: [1033:00e0] type 00 class 0x0c0320
pci 0000:00:02.0: reg 0x10: [mem 0x00000000-0x000000ff]
pci 0000:00:02.0: supports D1 D2
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot
PCI: bus0: Fast back to back transfers disabled
pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
pci 0000:00:01.0: can't enable device: BAR 0 [mem 0x00000000-0x00000fff] not claimed
pci 0000:00:01.0: Can't enable PCI device, BIOS handoff failed.
pci 0000:00:02.0: can't enable device: BAR 0 [mem 0x00000000-0x000000ff] not claimed
pci 0000:00:02.0: Can't enable PCI device, BIOS handoff failed.
pci 0000:00:01.0: BAR 0: assigned [mem 0xee080000-0xee080fff]
pci 0000:00:02.0: BAR 0: assigned [mem 0xee081000-0xee0810ff]
pci-rcar-gen2 ee0b0000.pci: PCI: bus0 revision 11
pci-rcar-gen2 ee0b0000.pci: PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [io 0xee0a0000-0xee0a10ff]
pci_bus 0000:01: root bus resource [mem 0xee0a0000-0xee0a10ff]
pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
pci 0000:01:00.0: [1033:0000] type 00 class 0x060000
pci 0000:01:00.0: reg 0x10: [mem 0xee0b0800-0xee0b0bff]
pci 0000:01:00.0: reg 0x14: [mem 0x40000000-0x7fffffff pref]
pci 0000:01:01.0: [1033:0035] type 00 class 0x0c0310
pci 0000:01:01.0: reg 0x10: [mem 0x00000000-0x00000fff]
pci 0000:01:01.0: supports D1 D2
pci 0000:01:01.0: PME# supported from D0 D1 D2 D3hot
pci 0000:01:02.0: [1033:00e0] type 00 class 0x0c0320
pci 0000:01:02.0: reg 0x10: [mem 0x00000000-0x000000ff]
pci 0000:01:02.0: supports D1 D2
pci 0000:01:02.0: PME# supported from D0 D1 D2 D3hot
PCI: bus1: Fast back to back transfers disabled
pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
pci 0000:01:01.0: can't enable device: BAR 0 [mem 0x00000000-0x00000fff] not claimed
pci 0000:01:01.0: Can't enable PCI device, BIOS handoff failed.
pci 0000:01:02.0: can't enable device: BAR 0 [mem 0x00000000-0x000000ff] not claimed
pci 0000:01:02.0: Can't enable PCI device, BIOS handoff failed.
pci 0000:01:01.0: BAR 0: assigned [mem 0xee0a0000-0xee0a0fff]
pci 0000:01:02.0: BAR 0: assigned [mem 0xee0a1000-0xee0a10ff]
pci-rcar-gen2 ee0d0000.pci: PCI: bus0 revision 11
pci-rcar-gen2 ee0d0000.pci: PCI host bridge to bus 0000:02
pci_bus 0000:02: root bus resource [io 0xee0c0000-0xee0c10ff]
pci_bus 0000:02: root bus resource [mem 0xee0c0000-0xee0c10ff]
pci_bus 0000:02: No busn resource found for root bus, will use [bus 02-ff]
pci 0000:02:00.0: [1033:0000] type 00 class 0x060000
pci 0000:02:00.0: reg 0x10: [mem 0xee0d0800-0xee0d0bff]
pci 0000:02:00.0: reg 0x14: [mem 0x40000000-0x7fffffff pref]
pci 0000:02:01.0: [1033:0035] type 00 class 0x0c0310
pci 0000:02:01.0: reg 0x10: [mem 0x00000000-0x00000fff]
pci 0000:02:01.0: supports D1 D2
pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot
pci 0000:02:02.0: [1033:00e0] type 00 class 0x0c0320
pci 0000:02:02.0: reg 0x10: [mem 0x00000000-0x000000ff]
pci 0000:02:02.0: supports D1 D2
pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot
PCI: bus2: Fast back to back transfers disabled
pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
pci 0000:02:01.0: can't enable device: BAR 0 [mem 0x00000000-0x00000fff] not claimed
pci 0000:02:01.0: Can't enable PCI device, BIOS handoff failed.
pci 0000:02:02.0: can't enable device: BAR 0 [mem 0x00000000-0x000000ff] not claimed
pci 0000:02:02.0: Can't enable PCI device, BIOS handoff failed.
pci 0000:02:01.0: BAR 0: assigned [mem 0xee0c0000-0xee0c0fff]
pci 0000:02:02.0: BAR 0: assigned [mem 0xee0c1000-0xee0c10ff]
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
SuperH (H)SCI(F) driver initialized
e6c40000.serial: ttySC6 at MMIO 0xe6c40000 (irq = 101, base_baud = 0) is a scifa
console [ttySC6] enabled
e6c50000.serial: ttySC7 at MMIO 0xe6c50000 (irq = 102, base_baud = 0) is a scifa
[drm] Initialized drm 1.1.0 20060810
rcar-du feb00000.display: fb0: frame buffer device
rcar-du feb00000.display: registered panic notifier
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] No driver support for vblank timestamp query.
[drm] Initialized rcar-du 1.0.0 20130110 on minor 0
scsi host0: sata_rcar
ata1: SATA max UDMA/133 irq 104
renesas_spi e6b10000.spi: dma_request_slave_channel_compat failed
renesas_spi e6b10000.spi: DMA not available, using PIO
m25p80 spi0.0: s25fl512s (65536 Kbytes)
3 ofpart partitions found on MTD device spi0.0
Creating 3 MTD partitions on "spi0.0":
0x000000000000-0x000000040000 : "loader"
0x000000040000-0x000000440000 : "user"
0x000000440000-0x000004000000 : "flash"
renesas_spi e6b10000.spi: probed
spi_sh_msiof e6e10000.spi: dma_request_slave_channel_compat failed
spi_sh_msiof e6e10000.spi: DMA not available, using PIO
libphy: sh_mii: probed
sh-eth ee700000.ethernet eth0: Base address at 0xee700000, 2e:09:0a:00:6e:71, IRQ 103.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:02.0: enabling device (0140 -> 0142)
ehci-pci 0000:00:02.0: EHCI Host Controller
ehci-pci 0000:00:02.0: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:02.0: irq 117, io mem 0xee081000
ehci-pci 0000:00:02.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci-pci 0000:01:02.0: enabling device (0140 -> 0142)
ehci-pci 0000:01:02.0: EHCI Host Controller
ehci-pci 0000:01:02.0: new USB bus registered, assigned bus number 2
ehci-pci 0000:01:02.0: irq 118, io mem 0xee0a1000
ehci-pci 0000:01:02.0: USB 2.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ehci-pci 0000:02:02.0: enabling device (0140 -> 0142)
ehci-pci 0000:02:02.0: EHCI Host Controller
ehci-pci 0000:02:02.0: new USB bus registered, assigned bus number 3
ehci-pci 0000:02:02.0: irq 119, io mem 0xee0c1000
ehci-pci 0000:02:02.0: USB 2.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-pci: OHCI PCI platform driver
ohci-pci 0000:00:01.0: enabling device (0140 -> 0142)
ohci-pci 0000:00:01.0: OHCI PCI host controller
ohci-pci 0000:00:01.0: new USB bus registered, assigned bus number 4
ohci-pci 0000:00:01.0: irq 117, io mem 0xee080000
ohci-pci 0000:00:01.0: init err (00002edf 0000)
ohci-pci 0000:00:01.0: can't start
ohci-pci 0000:00:01.0: startup error -75
ohci-pci 0000:00:01.0: USB bus 4 deregistered
ohci-pci 0000:00:01.0: init 0000:00:01.0 fail, -75
ohci-pci: probe of 0000:00:01.0 failed with error -75
ohci-pci 0000:01:01.0: enabling device (0140 -> 0142)
ohci-pci 0000:01:01.0: OHCI PCI host controller
ohci-pci 0000:01:01.0: new USB bus registered, assigned bus number 4
ohci-pci 0000:01:01.0: irq 118, io mem 0xee0a0000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
ohci-pci 0000:02:01.0: enabling device (0140 -> 0142)
ata1: link resume succeeded after 1 retries
ohci-pci 0000:02:01.0: OHCI PCI host controller
ohci-pci 0000:02:01.0: new USB bus registered, assigned bus number 5
ohci-pci 0000:02:01.0: irq 119, io mem 0xee0c0000
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
sh-pfc e6060000.pfc: pin GP_5_19 already requested by ee090000.pci; cannot claim for e6590000.usb
ata1: SATA link down (SStatus 0 SControl 300)
sh-pfc e6060000.pfc: pin-179 (e6590000.usb) status -22
sh-pfc e6060000.pfc: could not request pin 179 (GP_5_19) from group usb0_ovc_vbus on device sh-pfc
renesas_usbhs e6590000.usb: Error applying setting, reverse things back
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
of_dma_request_slave_channel: dma-names property of node '/usb@e6590000' missing or empty
renesas_usbhs e6590000.usb: gadget probed
renesas_usbhs e6590000.usb: platform init failed.
Unable to handle kernel NULL pointer dereference at virtual address 0000000d
pgd = c0004000
[0000000d] *pgd\0000000
Internal error: Oops: 5 [#1] SMP ARM
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc5-00129-gabd2dbf #961
Hardware name: lager
task: ee84bb40 ti: ee84c000 task.ti: ee84c000
PC is at dma_release_channel+0x18/0xbc
LR is at dma_release_channel+0x18/0xbc
pc : [<c01e7fe8>] lr : [<c01e7fe8>] psr: 60000113
sp : ee84dd78 ip : ee84dd78 fp : ee84dd8c
r10: c058f5d4 r9 : c05ce67c r8 : 00000024
r7 : edfec010 r6 : 00000000 r5 : edfec100 r4 : ffffffed
r3 : 00000003 r2 : ee84dd60 r1 : 0002dfe4 r0 : c05f8e90
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c5307d Table: 4000406a DAC: 00000015
Process swapper/0 (pid: 1, stack limit = 0xee84c238)
Stack: (0xee84dd78 to 0xee84e000)
dd60: 00000000 edfec100
dd80: ee84ddb4 ee84dd90 c02d06c0 c01e7fdc 00000003 edfec010 eea78e00 ffffffed
dda0: eea78e10 00000000 ee84dde4 ee84ddb8 c02cd524 c02d069c eea78e18 00000004
ddc0: eea78e10 ffffffed eea78e10 c0605bd0 c0605bd0 c05c4c78 ee84de04 ee84dde8
dde0: c024b54c c02cd1a8 c024b4fc eea78e10 00000000 00000000 ee84de24 ee84de08
de00: c024a010 c024b508 eea78e10 eea78e44 c0605bd0 00000000 ee84de44 ee84de28
de20: c024a1c4 c0249f4c c024a15c c0605bd0 ee84de48 c024a15c ee84de6c ee84de48
de40: c024895c c024a168 ee82d15c eea37f34 c0605bd0 ee153f00 c0600d78 00000000
de60: ee84de7c ee84de70 c024a2e0 c024890c ee84dea4 ee84de80 c02490ec c024a2cc
de80: c056d039 ee84de90 c0605bd0 edfe9240 00000000 c05c4c78 ee84debc ee84dea8
dea0: c024a9f0 c0249044 c05ab770 edfe9240 ee84decc ee84dec0 c024bdb4 c024a958
dec0: ee84dedc ee84ded0 c05ab788 c024bd70 ee84df54 ee84dee0 c058fdc8 c05ab77c
dee0: 60000113 ef7fccf7 ee84df0c ee84def8 c058f500 c01a9c94 c058f5d4 c056e1da
df00: ee84df54 ee84df10 c003c47c c058f5e0 ef7fccfe 00000006 00000006 000000aa
df20: c058c0e8 00000000 ee84df54 00000006 00000006 c05c54d0 c05c54b0 c06143c0
df40: 000000aa c05ce67c ee84df94 ee84df58 c058ff84 c058fccc 00000006 00000006
df60: c058f5d4 00041164 ffffffff 00000000 c0469290 00000000 00000000 00000000
df80: 00000000 00000000 ee84dfac ee84df98 c04692a0 c058fe84 ee84c000 00000000
dfa0: 00000000 ee84dfb0 c000ebf8 c046929c 00000000 00000000 00000000 00000000
dfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
dfe0: 00000000 00000000 00000000 00000000 00000013 00000000 5303c810 7110f809
Backtrace:
[<c01e7fd0>] (dma_release_channel) from [<c02d06c0>] (usbhs_fifo_remove+0x30/0x60)
r5:edfec100 r4:00000000
[<c02d0690>] (usbhs_fifo_remove) from [<c02cd524>] (usbhs_probe+0x388/0x3f0)
r8:00000000 r7:eea78e10 r6:ffffffed r5:eea78e00 r4:edfec010 r3:00000003
[<c02cd19c>] (usbhs_probe) from [<c024b54c>] (platform_drv_probe+0x50/0x98)
r8:c05c4c78 r7:c0605bd0 r6:c0605bd0 r5:eea78e10 r4:ffffffed
[<c024b4fc>] (platform_drv_probe) from [<c024a010>] (driver_probe_device+0xd0/0x21c)
r6:00000000 r5:00000000 r4:eea78e10 r3:c024b4fc
[<c0249f40>] (driver_probe_device) from [<c024a1c4>] (__driver_attach+0x68/0x8c)
r7:00000000 r6:c0605bd0 r5:eea78e44 r4:eea78e10
[<c024a15c>] (__driver_attach) from [<c024895c>] (bus_for_each_dev+0x5c/0x94)
r6:c024a15c r5:ee84de48 r4:c0605bd0 r3:c024a15c
[<c0248900>] (bus_for_each_dev) from [<c024a2e0>] (driver_attach+0x20/0x28)
r7:00000000 r6:c0600d78 r5:ee153f00 r4:c0605bd0
[<c024a2c0>] (driver_attach) from [<c02490ec>] (bus_add_driver+0xb4/0x1bc)
[<c0249038>] (bus_add_driver) from [<c024a9f0>] (driver_register+0xa4/0xe8)
r7:c05c4c78 r6:00000000 r5:edfe9240 r4:c0605bd0
[<c024a94c>] (driver_register) from [<c024bdb4>] (__platform_driver_register+0x50/0x64)
r5:edfe9240 r4:c05ab770
[<c024bd64>] (__platform_driver_register) from [<c05ab788>] (renesas_usbhs_driver_init+0x18/0x20)
[<c05ab770>] (renesas_usbhs_driver_init) from [<c058fdc8>] (do_one_initcall+0x108/0x1b8)
[<c058fcc0>] (do_one_initcall) from [<c058ff84>] (kernel_init_freeable+0x10c/0x1d8)
r9:c05ce67c r8:000000aa r7:c06143c0 r6:c05c54b0 r5:c05c54d0 r4:00000006
[<c058fe78>] (kernel_init_freeable) from [<c04692a0>] (kernel_init+0x10/0xec)
r10:00000000 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:c0469290
r4:00000000
[<c0469290>] (kernel_init) from [<c000ebf8>] (ret_from_fork+0x14/0x3c)
r4:00000000 r3:ee84c000
Code: e24cb004 e1a04000 e59f0094 eb0a1caa (e5943020)
---[ end trace 06a71daccda9eecb ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
CPU2: stopping
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G D 3.19.0-rc5-00129-gabd2dbf #961
Hardware name: lager
Backtrace:
[<c0011854>] (dump_backtrace) from [<c00119f4>] (show_stack+0x18/0x1c)
r6:c05da90c r5:00000002 r4:00000000 r3:00200040
[<c00119dc>] (show_stack) from [<c046ca18>] (dump_stack+0x74/0x90)
[<c046c9a4>] (dump_stack) from [<c0014244>] (handle_IPI+0xcc/0x164)
r4:c06147ac r3:c05e830c
[<c0014178>] (handle_IPI) from [<c00093a8>] (gic_handle_irq+0x5c/0x64)
r5:ee86df78 r4:f0002000
[<c000934c>] (gic_handle_irq) from [<c00125c0>] (__irq_svc+0x40/0x54)
Exception stack(0xee86df78 to 0xee86dfc0)
df60: 00000000 00000000
df80: ee86dfd0 c001d980 c06141f0 c05da4f0 c0474304 c06147d4 4000406a 413fc0f2
dfa0: 00000000 ee86dfcc ee86dfd0 ee86dfc0 c000f6d4 c000f6d8 60000113 ffffffff
r6:ffffffff r5:60000113 r4:c000f6d8 r3:c000f6d4
[<c000f6a4>] (arch_cpu_idle) from [<c005186c>] (cpu_startup_entry+0xf4/0x170)
[<c0051778>] (cpu_startup_entry) from [<c0013efc>] (secondary_start_kernel+0x114/0x130)
[<c0013de8>] (secondary_start_kernel) from [<40009444>] (0x40009444)
r4:6e85006a r3:c000942c
CPU0: stopping
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G D 3.19.0-rc5-00129-gabd2dbf #961
Hardware name: lager
Backtrace:
[<c0011854>] (dump_backtrace) from [<c00119f4>] (show_stack+0x18/0x1c)
r6:c05da90c r5:00000000 r4:00000000 r3:00200000
[<c00119dc>] (show_stack) from [<c046ca18>] (dump_stack+0x74/0x90)
[<c046c9a4>] (dump_stack) from [<c0014244>] (handle_IPI+0xcc/0x164)
r4:c06147ac r3:c05e830c
[<c0014178>] (handle_IPI) from [<c00093a8>] (gic_handle_irq+0x5c/0x64)
r5:c05d3f40 r4:f0002000
[<c000934c>] (gic_handle_irq) from [<c00125c0>] (__irq_svc+0x40/0x54)
Exception stack(0xc05d3f40 to 0xc05d3f88)
3f40: 00000000 00000000 c05d3f98 c001d980 c06141f0 c05da4f0 c0474304 c06143c0
3f60: c05c56a8 413fc0f2 ef7fcc80 c05d3f94 c05d3f98 c05d3f88 c000f6d4 c000f6d8
3f80: 60000113 ffffffff
r6:ffffffff r5:60000113 r4:c000f6d8 r3:c000f6d4
[<c000f6a4>] (arch_cpu_idle) from [<c005186c>] (cpu_startup_entry+0xf4/0x170)
[<c0051778>] (cpu_startup_entry) from [<c0469278>] (rest_init+0x68/0x80)
[<c0469210>] (rest_init) from [<c058fc54>] (start_kernel+0x34c/0x3b8)
[<c058f908>] (start_kernel) from [<40008074>] (0x40008074)
r10:00000000 r8:4000406a r7:c05de5cc r6:c05c56a4 r5:c05da47c r4:c0614754
CPU3: stopping
CPU: 3 PID: 0 Comm: swapper/3 Tainted: G D 3.19.0-rc5-00129-gabd2dbf #961
Hardware name: lager
Backtrace:
[<c0011854>] (dump_backtrace) from [<c00119f4>] (show_stack+0x18/0x1c)
r6:c05da90c r5:00000003 r4:00000000 r3:00200040
[<c00119dc>] (show_stack) from [<c046ca18>] (dump_stack+0x74/0x90)
[<c046c9a4>] (dump_stack) from [<c0014244>] (handle_IPI+0xcc/0x164)
r4:c06147ac r3:c05e830c
[<c0014178>] (handle_IPI) from [<c00093a8>] (gic_handle_irq+0x5c/0x64)
r5:ee86ff78 r4:f0002000
[<c000934c>] (gic_handle_irq) from [<c00125c0>] (__irq_svc+0x40/0x54)
Exception stack(0xee86ff78 to 0xee86ffc0)
ff60: 00000000 00000000
ff80: ee86ffd0 c001d980 c06141f0 c05da4f0 c0474304 c06147d4 4000406a 413fc0f2
ffa0: 00000000 ee86ffcc ee86ffd0 ee86ffc0 c000f6d4 c000f6d8 60000113 ffffffff
r6:ffffffff r5:60000113 r4:c000f6d8 r3:c000f6d4
[<c000f6a4>] (arch_cpu_idle) from [<c005186c>] (cpu_startup_entry+0xf4/0x170)
[<c0051778>] (cpu_startup_entry) from [<c0013efc>] (secondary_start_kernel+0x114/0x130)
[<c0013de8>] (secondary_start_kernel) from [<40009444>] (0x40009444)
r4:6e85006a r3:c000942c
drm_kms_helper: panic occurred, switching back to text console
---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
next prev parent reply other threads:[~2015-01-29 12:19 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-01-05 5:13 [PATCH 2/2] usb: renesas_usbhs: add support for SUDMAC Shimoda, Yoshihiro
2014-10-02 8:02 ` [PATCH 2/2] usb: renesas_usbhs: add support for generic PHY Yoshihiro Shimoda
2015-01-19 3:53 ` [PATCH 2/2] usb: renesas_usbhs: add support for requesting DT DMA Yoshihiro Shimoda
2015-01-29 12:19 ` Simon Horman [this message]
2015-01-30 1:43 ` yoshihiro shimoda
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150129121909.GA11832@verge.net.au \
--to=horms@verge.net.au \
--cc=linux-sh@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.