From: Siarhei Siamashka <siarhei.siamashka@gmail.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 17/17] sunxi: Hookup OTG USB controller support
Date: Mon, 9 Feb 2015 05:54:04 +0200 [thread overview]
Message-ID: <20150209055404.1d09f14a@i7> (raw)
In-Reply-To: <20150131045447.26e1eebc@i7>
On Sat, 31 Jan 2015 04:54:47 +0200
Siarhei Siamashka <siarhei.siamashka@gmail.com> wrote:
> On Sun, 11 Jan 2015 20:34:55 +0100
> Hans de Goede <hdegoede@redhat.com> wrote:
>
> > Hookup OTG USB controller support and enable the otg controller + USB-keyb
> > on various tablets.
> >
> > This allows tablet owners to interact with u-boot without needing to solder
> > a serial console onto their tablet PCB.
>
> Thanks. Works great on my Primo73 and Primo81 tablets. However I have
> just one naive question before happily taking it into use by default.
>
> Is the hardcoded otg host mode (without checking the id pin) always
> safe? For example, what happens if somebody connects a charger instead
> of a usb keyboard to the tablet?
So, does anyone have any idea if it is theoretically safe to have two
USB hosts connected to each other and both driving VBUS at +5V?
A somewhat realistic scenario is booting an Allwinner tablet over
USB using the FEL mode. Is it a good idea for such tablet to have
CONFIG_USB_MUSB_SUNXI=y and CONFIG_USB0_VBUS_PIN="axp_drivebus"
in defconfig?
--
Best regards,
Siarhei Siamashka
next prev parent reply other threads:[~2015-02-09 3:54 UTC|newest]
Thread overview: 31+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-01-11 19:34 [U-Boot] [PATCH 00/17] sunxi: musb otg controller support Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 01/17] sunxi: axp221: Protect axp221_init against multiple calls Hans de Goede
2015-01-13 18:49 ` Ian Campbell
2015-01-14 8:21 ` Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 02/17] sunxi: axp221: Add support for controlling the drivebus pin Hans de Goede
2015-01-13 18:52 ` Ian Campbell
2015-01-11 19:34 ` [U-Boot] [PATCH 03/17] sunxi: Move usb-controller init code out of ehci-sunxi.c for reuse for otg Hans de Goede
2015-01-13 18:55 ` Ian Campbell
2015-01-11 19:34 ` [U-Boot] [PATCH 04/17] sunxi: usbc: Add support for usb0 to the common usbc code Hans de Goede
2015-01-13 18:57 ` Ian Campbell
2015-01-11 19:34 ` [U-Boot] [PATCH 05/17] sunxi: usbc: Add support for usb-vbus0 controller by axp drivebus pin Hans de Goede
2015-01-13 18:58 ` Ian Campbell
2015-01-11 19:34 ` [U-Boot] [PATCH 06/17] usb: Fix usb_kbd_deregister when console-muxing is used Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 07/17] usb: Add an interval parameter to create_int_queue Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 08/17] usb: Do not log an error when no devices is plugged into a root-hub-less hcd Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 09/17] musb-new: Add register defines for different reg layout on sunxi Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 10/17] musb-new: Add sunxi musb controller support Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 11/17] musb-new: Use time based timeouts rather then cpu-cycles based timeouts Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 12/17] musb-new: Fix interrupt transfers not working Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 13/17] musb-new: Fix reset sequence when in host mode Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 14/17] musb-new: Properly remove a transfer from the schedule on timeout Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 15/17] musb-new: Add urb and hep parameters to construct_urb Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 16/17] musb-new: Add interrupt queue support Hans de Goede
2015-01-11 19:34 ` [U-Boot] [PATCH 17/17] sunxi: Hookup OTG USB controller support Hans de Goede
2015-01-13 19:59 ` Ian Campbell
2015-01-14 7:48 ` Hans de Goede
2015-01-31 2:54 ` Siarhei Siamashka
2015-02-09 3:54 ` Siarhei Siamashka [this message]
2015-02-09 22:10 ` Michal Suchanek
2015-02-10 8:24 ` Hans de Goede
2015-01-12 2:59 ` [U-Boot] [PATCH 00/17] sunxi: musb otg " Marek Vasut
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150209055404.1d09f14a@i7 \
--to=siarhei.siamashka@gmail.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.