[PATCH 2/2] ARM: dts: imx6: add support for technexion toucan board

[shawn.guo@linaro.org (Shawn Guo)]

On Fri, Feb 20, 2015 at 07:33:15PM +0100, Michael Grzeschik wrote:
> This patch adds the second user of the edm1 module.
> 
> Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
> ---
>  arch/arm/boot/dts/Makefile          |   1 +
>  arch/arm/boot/dts/imx6dl-toucan.dts | 203 ++++++++++++++++++++++++++++++++++++
>  2 files changed, 204 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6dl-toucan.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 91bd5bd..bea96c8 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -234,6 +234,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
>  	imx6dl-tx6dl-comtft.dtb \
>  	imx6dl-tx6u-801x.dtb \
>  	imx6dl-tx6u-811x.dtb \
> +	imx6dl-toucan.dtb \

'o' goes before 'x' in alphabet table.

>  	imx6dl-wandboard.dtb \
>  	imx6dl-wandboard-revb1.dtb \
>  	imx6q-arm2.dtb \
> diff --git a/arch/arm/boot/dts/imx6dl-toucan.dts b/arch/arm/boot/dts/imx6dl-toucan.dts
> new file mode 100644
> index 0000000..c801774
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6dl-toucan.dts
> @@ -0,0 +1,203 @@
> +/*
> + * Copyright 2015 Michael Grzeschik <mgr@pengutronix.de>, Pengutronix
> + *
> + * The code contained herein is licensed under the GNU General Public
> + * License. You may obtain a copy of the GNU General Public License
> + * Version 2 or later at the following locations:
> + *
> + * http://www.opensource.org/licenses/gpl-license.html
> + * http://www.gnu.org/copyleft/gpl.html
> + */
> +/dts-v1/;
> +
> +#include "imx6dl.dtsi"
> +#include "imx6qdl-edm1.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> +	model = "Technexion Toucan";
> +	compatible = "technexion,toucan", "fsl,imx6dl";
> +
> +	memory {
> +		reg = <0x10000000 0x40000000>;
> +	};
> +
> +	regulators {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		reg_usbotg_vbus: regulator at 0 {
> +			compatible = "regulator-fixed";
> +			reg = <7>;

'reg' value should match @unit-address.

> +			regulator-name = "usbotg_vbus";
> +			regulator-min-microvolt = <5000000>;
> +			regulator-max-microvolt = <5000000>;
> +			pinctrl-names = "default";
> +			gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> +			enable-active-high;
> +		};
> +
> +		reg_2p5v: regulator at 1 {
> +			compatible = "regulator-fixed";
> +			reg = <0>;
> +			regulator-name = "2P5V";
> +			regulator-min-microvolt = <2500000>;
> +			regulator-max-microvolt = <2500000>;
> +			regulator-always-on;
> +		};
> +
> +		reg_3p3v: regulator at 2 {
> +			compatible = "regulator-fixed";
> +			reg = <1>;
> +			regulator-name = "3P3V";
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3300000>;
> +			regulator-always-on;
> +		};
> +	};
> +
> +	sound {
> +		compatible = "fsl,imx6-toucan-sgtl5000",
> +			     "fsl,imx-audio-sgtl5000";
> +		model = "imx6-toucan-sgtl5000";
> +		ssi-controller = <&ssi1>;
> +		audio-codec = <&codec>;
> +		audio-routing =
> +			"MIC_IN", "Mic Jack",
> +			"Mic Jack", "Mic Bias",
> +			"Headphone Jack", "HP_OUT";
> +		mux-int-port = <1>;
> +		mux-ext-port = <3>;
> +	};

Can generic simple-audio-card be used instead?

> +};
> +
> +&iomuxc {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_hog>;
> +
> +	imx6qdl-toucan {
> +		pinctrl_hog: hoggrp {
> +			fsl,pins = <
> +				MX6QDL_PAD_CSI0_DAT19__GPIO6_IO05	0x0b0b0
> +				MX6QDL_PAD_CSI0_DAT16__GPIO6_IO02	0x0b0b0
> +				MX6QDL_PAD_CSI0_DAT18__GPIO6_IO04	0x0b0b0
> +				MX6QDL_PAD_EIM_D27__GPIO3_IO27		0x0b0b0
> +				MX6QDL_PAD_EIM_D26__GPIO3_IO26		0x0b0b0
> +				MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0x0b0b0
> +				MX6QDL_PAD_CSI0_DAT17__GPIO6_IO03	0x0b0b0
> +				MX6QDL_PAD_ENET_RX_ER__GPIO1_IO24	0x0b0b0
> +				MX6QDL_PAD_SD3_RST__GPIO7_IO08		0x0b0b0
> +				MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x0b0b0
> +				MX6QDL_PAD_SD4_DAT0__GPIO2_IO08         0x17059
> +			>;
> +		};
> +	};
> +};
> +
> +&fec {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enet>;
> +	phy-mode = "rgmii";
> +	phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
> +	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
> +			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
> +	status = "okay";
> +};
> +
> +&audmux {

Please sort these nodes alphabetically in label name.

Shawn

> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_audmux>;
> +	status = "okay";
> +};
> +
> +&usbh1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usbh1>;
> +	dr_mode = "host";
> +	disable-over-current;
> +	status = "okay";
> +};
> +
> +&usbotg {
> +	vbus-supply = <&reg_usbotg_vbus>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usbotg>;
> +	dr_mode = "peripheral";
> +	disable-over-current;
> +	status = "okay";
> +};
> +
> +&can1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan1>;
> +	status = "okay";
> +};
> +
> +&can2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_flexcan2>;
> +	status = "okay";
> +};
> +
> +&ssi1 {
> +	status = "okay";
> +};
> +
> +&hdmi {
> +	ddc-i2c-bus = <&i2c1>;
> +	status = "okay";
> +};
> +
> +&i2c1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	clock-frequency = <400000>;
> +	status = "okay";
> +};
> +
> +&i2c2 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c2>;
> +	status = "okay";
> +
> +	codec: sgtl5000 at 0a {
> +		compatible = "fsl,sgtl5000";
> +		reg = <0x0a>;
> +		clocks = <&clks 201>;
> +		VDDA-supply = <&reg_2p5v>;
> +		VDDIO-supply = <&reg_3p3v>;
> +	};
> +};
> +
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_rtscts>;
> +	status = "okay";
> +};
> +
> +&uart2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart2 &pinctrl_uart2_rtscts>;
> +	status = "okay";
> +};
> +
> +&usdhc1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc1>;
> +	bus-width = <4>;
> +	no-1-8-v;
> +	cd-gpios = <&gpio1 2 0>;
> +	fsl,wp-controller;
> +	status = "okay";
> +};
> +
> +&usdhc3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc3>;
> +	bus-width = <4>;
> +	no-1-8-v;
> +	fsl,wp-controller;
> +	status = "okay";
> +};
> -- 
> 2.1.4
>