[U-Boot] CONFIG_DM_ETH USB_ETHER_ASIX Reception Issue on Tegra

[Marek Vasut <marex@denx.de>]

On Friday, August 07, 2015 at 09:09:15 PM, Simon Glass wrote:
> Hi Marcel,
> 
> On 7 August 2015 at 00:41, Marcel Ziswiler <marcel@ziswiler.com> wrote:
> > On Thu, 2015-08-06 at 23:29 -0600, Simon Glass wrote:
> >> The memalign() function arguments are around the wrong way!
> > 
> > I assume you meant that one:
> > 
> > diff --git a/drivers/usb/eth/usb_ether.c b/drivers/usb/eth/usb_ether.c
> > index 3c3e082..11d26be 100644
> > --- a/drivers/usb/eth/usb_ether.c
> > +++ b/drivers/usb/eth/usb_ether.c
> > @@ -73,7 +73,7 @@ int usb_ether_register(struct udevice *dev, struct
> > ueth_data *ueth, int rxsize)
> > 
> >         }
> >         
> >         ueth->rxsize = rxsize;
> > 
> > -       ueth->rxbuf = memalign(rxsize, ARCH_DMA_MINALIGN);
> > +       ueth->rxbuf = memalign(ARCH_DMA_MINALIGN, rxsize);
> > 
> >         if (!ueth->rxbuf)
> >         
> >                 return -ENOMEM;
> >> 
> >> Definitely
> >> worth seeing if that fixes it. For some reason rpi and minnowboard
> >> seem to work even with this error.
> > 
> > Unfortunately still the same:
> > 
> > U-Boot SPL 2015.10-rc1-00188-gfac971b-dirty (Aug 07 2015 - 06:34:28)
> > 
> > 
> > U-Boot 2015.10-rc1-00188-gfac971b-dirty (Aug 07 2015 - 06:34:28 +0000)
> > 
> > TEGRA20
> > Model: Toradex Colibri T20
> > Board: Toradex Colibri T20
> > DRAM:  512 MiB
> > NAND:  1024 MiB
> > MMC:   Tegra SD/MMC: 0
> > *** Warning - bad CRC, using default environment
> > 
> > In:    serial
> > Out:   serial
> > Err:   serial
> > Net:   Net Initialization Skipped
> > No ethernet found.
> > Hit any key to stop autoboot:  0
> > Colibri T20 # usb start
> > starting USB...
> > USB0:   USB EHCI 1.00
> > USB1:   USB EHCI 1.00
> > USB2:   USB EHCI 1.00
> > scanning bus 1 for devices... 1 USB Device(s) found
> > scanning bus 2 for devices...
> > Warning: asix_eth using MAC address from ROM
> > 2 USB Device(s) found
> > scanning bus 0 for devices... 1 USB Device(s) found
> > Colibri T20 # dhcp
> > BOOTP broadcast 1
> > BOOTP broadcast 2
> > BOOTP broadcast 3
> > EHCI timed out on TD - token=0x8008d80
> > Rx: failed to receive: -5
> > BOOTP broadcast 4
> > BOOTP broadcast 5
> > EHCI timed out on TD - token=0x88008d80
> > Rx: failed to receive: -5
> > BOOTP broadcast 6
> > BOOTP broadcast 7
> > EHCI timed out on TD - token=0x8008d80
> > Rx: failed to receive: -5
> > BOOTP broadcast 8
> > BOOTP broadcast 9
> > EHCI timed out on TD - token=0x88008d80
> > Rx: failed to receive: -5
> > 
> > Retry time exceeded; starting again
> > Colibri T20 #
> 
> One point to make is that I have seen this on and off for a while.
> When I tested the driver model EHCI support I found this bug. But then
> when I turned off driver model it was still there. So I decided it was
> pre-existing. Also I'm not sure that this error is handled correctly.
> The code that times out does not retry properly.
> 
> Marek do

I think there's a bit of this sentence missing. But the fix I pushed was
for enumeration, not for this.

> Regards,
> Simon