All of lore.kernel.org
 help / color / mirror / Atom feed
From: Lee Jones <lee.jones@linaro.org>
To: Milo Kim <milo.kim@ti.com>
Cc: robh+dt@kernel.org, j.anaszewski@samsung.com, broonie@kernel.org,
	devicetree@vger.kernel.org, linux-leds@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2 5/9] mfd: add TI LMU driver
Date: Mon, 11 Jan 2016 10:17:29 +0000	[thread overview]
Message-ID: <20160111101729.GT14104@x1> (raw)
In-Reply-To: <1448521025-2796-6-git-send-email-milo.kim@ti.com>

On Thu, 26 Nov 2015, Milo Kim wrote:

> TI LMU (Lighting Management Unit) driver supports lighting devices below.
> 
>   LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
> 
> LMU devices have common features.
>   - I2C interface for accessing device registers
>   - Hardware enable pin control
>   - Backlight brightness control
>   - Notifier for hardware fault monitoring
>   - Regulators for LCD display bias
> 
> It contains fault monitor, backlight, LED and regulator driver.
> 
> LMU fault monitor
> -----------------
>   LM3633 and LM3697 provide hardware monitoring feature.
>   It enables open or short circuit detection.
>   After monitoring is done, each device should be re-initialized.
>   Notifier is used for this case.
>   Please refer to separate patch for 'ti-lmu-fault-monitor'.
> 
> Backlight
> ---------
>   It's handled by TI LMU backlight consolidated driver and
>   chip dependent data. Please refer to separate patches for
>   'ti-lmu-backlight'.
> 
> LED indicator
> -------------
>   LM3633 has 6 indicator LEDs. Programmable dimming pattern is also
>   supported. Please refer to separate patch for 'leds-lm3633'.
> 
> Regulator
> ---------
>   LM3631 has 5 regulators for the display bias.
>   LM3632 supports 3 regulators. One consolidated driver enables it.
>   Please refer to separate patch for 'lm363x-regulator'.
> 
> Cc: Lee Jones <lee.jones@linaro.org> 
> Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
> Cc: Mark Brown <broonie@kernel.org>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: devicetree@vger.kernel.org
> Cc: linux-leds@vger.kernel.org 
> Cc: linux-kernel@vger.kernel.org
> Signed-off-by: Milo Kim <milo.kim@ti.com>
> ---
>  drivers/mfd/Kconfig                 |  12 ++
>  drivers/mfd/Makefile                |   2 +
>  drivers/mfd/ti-lmu.c                | 259 +++++++++++++++++++++++++++++++++
>  include/linux/mfd/ti-lmu-register.h | 280 ++++++++++++++++++++++++++++++++++++
>  include/linux/mfd/ti-lmu.h          |  87 +++++++++++
>  5 files changed, 640 insertions(+)
>  create mode 100644 drivers/mfd/ti-lmu.c
>  create mode 100644 include/linux/mfd/ti-lmu-register.h
>  create mode 100644 include/linux/mfd/ti-lmu.h

Acked-by: Lee Jones <lee.jones@linaro.org>

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog

  reply	other threads:[~2016-01-11 10:17 UTC|newest]

Thread overview: 58+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-11-26  6:56 [PATCH v2 0/9] Support TI LMU devices Milo Kim
2015-11-26  6:56 ` Milo Kim
2015-11-26  6:56 ` [PATCH v2 1/9] Documentation: dt-bindings: mfd: add TI LMU device binding information Milo Kim
2015-11-26  6:56   ` Milo Kim
2015-11-27 20:55   ` Rob Herring
2016-01-11  9:46   ` Lee Jones
2015-11-26  6:56 ` [PATCH v2 2/9] Documentation: dt-bindings: leds: backlight: add TI LMU backlight " Milo Kim
2015-11-26  6:56   ` Milo Kim
2016-01-11  9:53   ` Lee Jones
2015-11-26  6:56 ` [PATCH v2 3/9] Documentation: dt-bindings: leds: add LM3633 LED " Milo Kim
2015-11-26  6:56   ` Milo Kim
2015-11-27 11:19   ` Jacek Anaszewski
2015-11-30  8:19     ` Kim, Milo
2015-11-30  8:19       ` Kim, Milo
2015-11-30 12:26       ` Jacek Anaszewski
     [not found]         ` <565C408B.9070703-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2015-12-07  8:46           ` Kim, Milo
2015-12-07  8:46             ` Kim, Milo
2015-12-07 10:50             ` Jacek Anaszewski
2015-11-26  6:57 ` [PATCH v2 4/9] Documentation: dt-bindings: regulator: add LM363x regulator " Milo Kim
2015-11-26  6:57   ` Milo Kim
2015-11-27 12:37   ` Mark Brown
2015-11-27 20:44     ` Rob Herring
2015-11-27 22:07       ` Mark Brown
2015-11-27 12:55   ` Applied "regulator: lm363x: add LM363x regulator binding information" to the regulator tree Mark Brown
2015-11-27 20:57   ` [PATCH v2 4/9] Documentation: dt-bindings: regulator: add LM363x regulator binding information Rob Herring
2015-11-26  6:57 ` [PATCH v2 5/9] mfd: add TI LMU driver Milo Kim
2015-11-26  6:57   ` Milo Kim
2016-01-11 10:17   ` Lee Jones [this message]
2015-11-26  6:57 ` [PATCH v2 6/9] mfd: add TI LMU hardware fault monitoring driver Milo Kim
2015-11-26  6:57   ` Milo Kim
2016-01-11 10:21   ` Lee Jones
2016-01-12  3:36     ` Milo Kim
2016-01-12  3:36       ` Milo Kim
2016-01-12  7:37       ` Lee Jones
2015-11-26  6:57 ` [PATCH v2 7/9] backlight: add TI LMU backlight driver Milo Kim
2015-11-26  6:57   ` Milo Kim
2016-01-11  9:57   ` Lee Jones
2016-01-11 23:32     ` Milo Kim
2016-01-11 23:32       ` Milo Kim
2015-11-26  6:57 ` [PATCH v2 8/9] leds: add LM3633 driver Milo Kim
2015-11-26  6:57   ` Milo Kim
2015-11-27 11:19   ` Jacek Anaszewski
     [not found]     ` <56583C37.1050307-Sze3O3UU22JBDgjK7y7TUQ@public.gmane.org>
2015-11-28  8:28       ` Jacek Anaszewski
2015-11-28  8:28         ` Jacek Anaszewski
2015-11-30  8:48     ` Kim, Milo
2015-11-30  8:48       ` Kim, Milo
2015-11-30 12:26       ` Jacek Anaszewski
2015-11-26  6:57 ` [PATCH v2 9/9] regulator: add LM363X driver Milo Kim
2015-11-26  6:57   ` Milo Kim
2015-11-27 12:55   ` Applied "regulator: add LM363X driver" to the regulator tree Mark Brown
2016-01-14  7:56   ` [PATCH v2 9/9] regulator: add LM363X driver Milo Kim
2016-01-14  7:56     ` Milo Kim
     [not found]     ` <56975493.7050900-l0cyMroinI0@public.gmane.org>
2016-01-14 10:27       ` Mark Brown
2016-01-14 10:27         ` Mark Brown
2016-01-14 23:41         ` Kim, Milo
2016-01-14 23:41           ` Kim, Milo
2016-01-06  7:20 ` [PATCH v2 0/9] Support TI LMU devices Milo Kim
2016-01-06  7:20   ` Milo Kim

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20160111101729.GT14104@x1 \
    --to=lee.jones@linaro.org \
    --cc=broonie@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=j.anaszewski@samsung.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=milo.kim@ti.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.