From: Baoquan He <bhe-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
To: Mark Hounschell <markh-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
Cc: iommu-cunTk1MwBs9QetFLy7KEm3xJsTq8ys+cHZ5vskTnxNA@public.gmane.org
Subject: Re: Can't boot new 4.4 kernel with IOMMU enabled
Date: Thu, 14 Jan 2016 08:05:20 +0800 [thread overview]
Message-ID: <20160114000520.GA2449@x1.redhat.com> (raw)
In-Reply-To: <56966244.80700-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
On 01/13/16 at 09:42am, Mark Hounschell wrote:
> First, attached are the 2 lspci outputs you asked for.
>
> After the patch I was still unable to bring the system up but it was
> much better. 2 of the 8 Sata disks do not come up. If I remove those
> from my fstab the box comes up with the patch.
>
> This MB has 8 internal Sata ports. Six hanging off the South-Bridge
> (SB950) and two more hanging off Marvell 88SE9172 chips connected
> to the 990FX chipset. I'm pretty sure the 2 disks that don't come
> up are the 2 hanging off the Marvell chips. I will have to take the
> box apart to verify and will if you need me to. And again, all works
> fine with the IOMMU disabled in the BIOS.
OK, it means the alias dev table entry is correctly set. I checked the
boot log again and found some interrupt related info. Can you paste the
boot log which 2 of the 8 sata disks didn't come up with my patch
applied. And could you tell the pci id of those 2 sata disks, then I
don't need to find them one by one.
>
>
>
> -[0000:00]-+-00.0
> +-00.2
> +-02.0-[01]----00.0
> +-04.0-[02-05]----00.0-[03-05]----04.0-[04-05]--+-04.0
> | +-05.0
> | +-06.0
> | +-07.0
> | +-08.0-[05]----00.0
> | +-09.0
> | \-0a.0
> +-09.0-[06]----00.0
> +-0a.0-[07]----00.0
> +-0b.0-[08-0d]----00.0-[09-0d]----04.0-[0a-0d]--+-04.0
> | +-05.0
> | +-06.0-[0b]----00.0
> | +-07.0-[0c]----00.0
> | +-08.0-[0d]----00.0
> | +-09.0
> | \-0a.0
> +-0d.0-[0e-0f]----00.0-[0f]----04.0
> +-11.0
> +-12.0
> +-12.2
> +-13.0
> +-13.2
> +-14.0
> +-14.1
> +-14.2
> +-14.3
> +-14.4-[10]----06.0
> +-14.5
> +-15.0-[11]----00.0
> +-15.1-[12]----00.0
> +-15.2-[13]----00.0
> +-16.0
> +-16.2
> +-18.0
> +-18.1
> +-18.2
> +-18.3
> +-18.4
> \-18.5
> 00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (external gfx0 port B) (rev 02)
> Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (external gfx0 port B)
> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
> Capabilities: [f0] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [c4] HyperTransport: Slave or Primary Interface
> Command: BaseUnitID=0 UnitCnt=20 MastHost- DefDir- DUL-
> Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b+
> Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
> Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
> Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
> Revision ID: 3.00
> Link Frequency 0: [e]
> Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
> Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD-
> Link Frequency 1: 200MHz
> Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
> Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
> Prefetchable memory behind bridge Upper: 00-00
> Bus Number: 00
> Capabilities: [40] HyperTransport: Retry Mode
> Capabilities: [54] HyperTransport: UnitID Clumping
> Capabilities: [9c] HyperTransport: #1a
> Capabilities: [70] MSI: Enable- Count=1/4 Maskable- 64bit-
> Address: 00000000 Data: 0000
>
> 00:00.2 IOMMU: Advanced Micro Devices, Inc. [AMD/ATI] RD990 I/O Memory Management Unit (IOMMU)
> Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] RD990 I/O Memory Management Unit (IOMMU)
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 26
> Capabilities: [40] Secure device <?>
> Capabilities: [54] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000feeff00c Data: 4142
> Capabilities: [64] HyperTransport: MSI Mapping Enable+ Fixed+
>
> 00:02.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (PCI express gpp port B) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> I/O behind bridge: 0000e000-0000efff
> Memory behind bridge: d9000000-db0fffff
> Prefetchable memory behind bridge: 00000000b0000000-00000000bfffffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag+ RBE+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <1us, L1 <8us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
> Slot #2, PowerLimit 75.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd+
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
> Address: 00000000 Data: 0000
> Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 5a14
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
> Capabilities: [190 v1] Access Control Services
> ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans+
> ACSCtl: SrcValid+ TransBlk- ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans-
> Kernel driver in use: pcieport
> Kernel modules: shpchp
>
> 00:04.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (PCI express gpp port D) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=02, subordinate=05, sec-latency=0
> I/O behind bridge: 00006000-00007fff
> Memory behind bridge: db800000-dd9fffff
> Prefetchable memory behind bridge: 00000000c0000000-00000000c3ffffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag+ RBE+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <1us, L1 <8us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
> Slot #4, PowerLimit 75.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd+
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
> Address: 00000000 Data: 0000
> Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 5a14
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
> Capabilities: [190 v1] Access Control Services
> ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans+
> ACSCtl: SrcValid+ TransBlk- ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans-
> Kernel driver in use: pcieport
> Kernel modules: shpchp
>
> 00:09.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (PCI express gpp port H) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: de100000-de1fffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag+ RBE+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
> LnkCap: Port #1, Speed 5GT/s, Width x2, ASPM L0s L1, Exit Latency L0s <1us, L1 <8us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt+
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
> Slot #9, PowerLimit 75.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd+
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
> Address: 00000000 Data: 0000
> Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 5a14
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
> Capabilities: [190 v1] Access Control Services
> ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans+
> ACSCtl: SrcValid+ TransBlk- ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans-
> Kernel driver in use: pcieport
> Kernel modules: shpchp
>
> 00:0a.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (external gfx1 port A) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: de000000-de0fffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag+ RBE+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
> LnkCap: Port #2, Speed 5GT/s, Width x2, ASPM L0s L1, Exit Latency L0s <1us, L1 <8us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt+
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
> Slot #10, PowerLimit 75.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd+
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
> Address: 00000000 Data: 0000
> Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 5a14
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
> Capabilities: [190 v1] Access Control Services
> ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans+
> ACSCtl: SrcValid+ TransBlk- ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans-
> Kernel driver in use: pcieport
> Kernel modules: shpchp
>
> 00:0b.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (NB-SB link) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=08, subordinate=0d, sec-latency=0
> I/O behind bridge: 0000c000-0000cfff
> Memory behind bridge: d0000000-d87fffff
> Prefetchable memory behind bridge: 00000000c4000000-00000000c6ffffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag+ RBE+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <1us, L1 <8us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
> Slot #11, PowerLimit 75.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd+
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
> Address: 00000000 Data: 0000
> Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 5a14
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
> Capabilities: [190 v1] Access Control Services
> ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans+
> ACSCtl: SrcValid+ TransBlk- ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans-
> Kernel driver in use: pcieport
> Kernel modules: shpchp
>
> 00:0d.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890 PCI to PCI bridge (external gfx1 port B) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=0e, subordinate=0f, sec-latency=0
> I/O behind bridge: 0000b000-0000bfff
> Memory behind bridge: ddb00000-ddcfffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot+), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag+ RBE+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <1us, L1 <8us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
> Slot #13, PowerLimit 75.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
> Changed: MRL- PresDet- LinkState-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd+
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
> Address: 00000000 Data: 0000
> Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 5a14
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
> Capabilities: [190 v1] Access Control Services
> ACSCap: SrcValid+ TransBlk+ ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans+
> ACSCtl: SrcValid+ TransBlk- ReqRedir+ CmpltRedir+ UpstreamFwd+ EgressCtrl- DirectTrans-
> Kernel driver in use: pcieport
> Kernel modules: shpchp
>
> 00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] (rev 40) (prog-if 01 [AHCI 1.0])
> Subsystem: Gigabyte Technology Co., Ltd Device b002
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32
> Interrupt: pin A routed to IRQ 19
> Region 0: I/O ports at f090 [size=8]
> Region 1: I/O ports at f080 [size=4]
> Region 2: I/O ports at f070 [size=8]
> Region 3: I/O ports at f060 [size=4]
> Region 4: I/O ports at f050 [size=16]
> Region 5: Memory at d880b000 (32-bit, non-prefetchable) [size=1K]
> Capabilities: [70] SATA HBA v1.0 InCfgSpace
> Capabilities: [a4] PCI Advanced Features
> AFCap: TP+ FLR+
> AFCtrl: FLR-
> AFStatus: TP-
> Kernel driver in use: ahci
>
> 00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
> Subsystem: Gigabyte Technology Co., Ltd Device 5004
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at d880a000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci-pci
> Kernel modules: ohci_pci
>
> 00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
> Subsystem: Gigabyte Technology Co., Ltd Device 5004
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at d8809000 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci-pci
>
> 00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
> Subsystem: Gigabyte Technology Co., Ltd Device 5004
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at d8808000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci-pci
> Kernel modules: ohci_pci
>
> 00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
> Subsystem: Gigabyte Technology Co., Ltd Device 5004
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at d8807000 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci-pci
>
> 00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller (rev 42)
> Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Kernel driver in use: piix4_smbus
> Kernel modules: i2c_piix4
>
> 00:14.1 IDE interface: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) (prog-if 8a [Master SecP PriP])
> Subsystem: Gigabyte Technology Co., Ltd Device 5002
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32
> Interrupt: pin B routed to IRQ 17
> Region 0: I/O ports at 01f0 [size=8]
> Region 1: I/O ports at 03f4
> Region 2: I/O ports at 0170 [size=8]
> Region 3: I/O ports at 0374
> Region 4: I/O ports at f000 [size=16]
> Kernel driver in use: pata_atiixp
> Kernel modules: pata_atiixp, pata_acpi, ata_generic
>
> 00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) (rev 40)
> Subsystem: Gigabyte Technology Co., Ltd Device a132
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at d8800000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: snd_hda_intel
> Kernel modules: snd_hda_intel
>
> 00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller (rev 40)
> Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
>
> 00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI Bridge (rev 40) (prog-if 01 [Subtractive decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 64
> Bus: primary=00, secondary=10, subordinate=10, sec-latency=64
> I/O behind bridge: 0000a000-0000afff
> Memory behind bridge: ddf00000-ddffffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>
> 00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI2 Controller (prog-if 10 [OHCI])
> Subsystem: Gigabyte Technology Co., Ltd Device 5004
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin C routed to IRQ 18
> Region 0: Memory at d8806000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci-pci
> Kernel modules: ohci_pci
>
> 00:15.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=11, subordinate=11, sec-latency=0
> I/O behind bridge: 00009000-00009fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000c7000000-00000000c70fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag+ RBE+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
> Kernel driver in use: pcieport
> Kernel modules: shpchp
>
> 00:15.1 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] SB700/SB800/SB900 PCI to PCI bridge (PCIE port 1) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=12, subordinate=12, sec-latency=0
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: dde00000-ddefffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag+ RBE+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
> LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
> Kernel driver in use: pcieport
> Kernel modules: shpchp
>
> 00:15.2 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] SB900 PCI to PCI bridge (PCIE port 2) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=00, secondary=13, subordinate=13, sec-latency=0
> I/O behind bridge: 00008000-00008fff
> Memory behind bridge: ddd00000-dddfffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] Express (v2) Root Port (Slot-), MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0
> ExtTag+ RBE+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 128 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
> LnkCap: Port #2, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <64ns, L1 <1us
> ClockPM- Surprise- LLActRep+ BwNot+
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible+
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
> DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [b0] Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] Device 0000
> Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
> Capabilities: [100 v1] Vendor Specific Information: ID=0001 Rev=1 Len=010 <?>
> Kernel driver in use: pcieport
> Kernel modules: shpchp
>
> 00:16.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
> Subsystem: Gigabyte Technology Co., Ltd Device 5004
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at d8805000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: ohci-pci
> Kernel modules: ohci_pci
>
> 00:16.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
> Subsystem: Gigabyte Technology Co., Ltd Device 5004
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin B routed to IRQ 17
> Region 0: Memory at d8804000 (32-bit, non-prefetchable) [size=256]
> Capabilities: [c0] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [e4] Debug port: BAR=1 offset=00e0
> Kernel driver in use: ehci-pci
>
> 00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 0
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Capabilities: [80] HyperTransport: Host or Secondary Interface
> Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
> Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b+
> Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
> Revision ID: 3.00
> Link Frequency: [e]
> Link Error: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
> Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
>
> 00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 1
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>
> 00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 2
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>
> 00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 3
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Capabilities: [f0] Secure device <?>
> Kernel driver in use: k10temp
> Kernel modules: k10temp
>
> 00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 4
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Kernel driver in use: fam15h_power
> Kernel modules: fam15h_power
>
> 00:18.5 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 15h Processor Function 5
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>
> 01:00.0 VGA compatible controller: NVIDIA Corporation G70 [GeForce 7800 GT] (rev a1) (prog-if 00 [VGA controller])
> Subsystem: eVga.com. Corp. Device c517
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 43
> Region 0: Memory at da000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at b0000000 (64-bit, prefetchable) [size=256M]
> Region 3: Memory at d9000000 (64-bit, non-prefetchable) [size=16M]
> Region 5: I/O ports at e000 [size=128]
> [virtual] Expansion ROM at db000000 [disabled] [size=128K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [78] Express (v1) Endpoint, MSI 00
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Exit Latency L0s <256ns, L1 <4us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> Capabilities: [100 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
> Status: NegoPending- InProgress-
> Capabilities: [128 v1] Power Budgeting <?>
> Kernel driver in use: nvidia
> Kernel modules: nvidiafb, nouveau, nvidia
>
> 02:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200A PCI Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=02, secondary=03, subordinate=05, sec-latency=32
> I/O behind bridge: 00006000-00007fff
> Memory behind bridge: db800000-dd9fffff
> Prefetchable memory behind bridge: 00000000c0000000-00000000c3ffffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [80] Subsystem: Device 0000:0000
> Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
> DevCap: MaxPayload 512 bytes, PhantFunc 0
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <16us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
> Kernel modules: shpchp
>
> 03:04.0 PCI bridge: Pericom Semiconductor PCI to PCI Bridge (rev 02) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Bus: primary=03, secondary=04, subordinate=05, sec-latency=32
> I/O behind bridge: 00006000-00007fff
> Memory behind bridge: db800000-dd9fffff
> Prefetchable memory behind bridge: 00000000c0000000-00000000c3ffffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [b0] Slot ID: 0 slots, First-, chassis 00
> Kernel modules: shpchp
>
> 04:04.0 Intelligent controller [0e80]: PLX Technology, Inc. Device 0480 (rev 55)
> Subsystem: Compro Computer Services, Inc. Device 4620
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 34
> BIST result: 00
> Region 0: Memory at dd909000 (32-bit, non-prefetchable) [size=1K]
> Region 1: Memory at dd000000 (32-bit, non-prefetchable) [size=8M]
> Region 2: Memory at dd908000 (32-bit, non-prefetchable) [size=16]
> Capabilities: [40] #00 [0000]
> Capabilities: [54] #00 [0080]
> Capabilities: [58] Vital Product Data
> Unknown large resource type 48, will not decode more.
> Kernel driver in use: gpiohsd
> Kernel modules: gpiohsd
>
> 04:05.0 Intelligent controller [0e80]: PLX Technology, Inc. Device 0480 (rev 55)
> Subsystem: Compro Computer Services, Inc. Device 4620
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 39
> BIST result: 00
> Region 0: Memory at dd907000 (32-bit, non-prefetchable) [size=1K]
> Region 1: Memory at dc800000 (32-bit, non-prefetchable) [size=8M]
> Region 2: Memory at dd906000 (32-bit, non-prefetchable) [size=16]
> Capabilities: [40] #00 [0000]
> Capabilities: [54] #00 [0080]
> Capabilities: [58] Vital Product Data
> Unknown large resource type 48, will not decode more.
> Kernel driver in use: gpiohsd
> Kernel modules: gpiohsd
>
> 04:06.0 Intelligent controller [0e80]: PLX Technology, Inc. Device 0480 (rev 55)
> Subsystem: Compro Computer Services, Inc. Device 4620
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 40
> BIST result: 00
> Region 0: Memory at dd905000 (32-bit, non-prefetchable) [size=1K]
> Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=8M]
> Region 2: Memory at dd904000 (32-bit, non-prefetchable) [size=16]
> Capabilities: [40] #00 [0000]
> Capabilities: [54] #00 [0080]
> Capabilities: [58] Vital Product Data
> Unknown large resource type 48, will not decode more.
> Kernel driver in use: gpiohsd
> Kernel modules: gpiohsd
>
> 04:07.0 Intelligent controller [0e80]: PLX Technology, Inc. Device 0480 (rev 55)
> Subsystem: Compro Computer Services, Inc. Device 4620
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 29
> BIST result: 00
> Region 0: Memory at dd903000 (32-bit, non-prefetchable) [size=1K]
> Region 1: Memory at db800000 (32-bit, non-prefetchable) [size=8M]
> Region 2: Memory at dd902000 (32-bit, non-prefetchable) [size=16]
> Capabilities: [40] #00 [0000]
> Capabilities: [54] #00 [0080]
> Capabilities: [58] Vital Product Data
> Unknown large resource type 48, will not decode more.
> Kernel driver in use: gpiohsd
> Kernel modules: gpiohsd
>
> 04:08.0 PCI bridge: Hint Corp HiNT HB4 PCI-PCI Bridge (PCI6150) (rev 04) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Bus: primary=04, secondary=05, subordinate=05, sec-latency=32
> I/O behind bridge: 00006000-00006fff
> Memory behind bridge: dd800000-dd8fffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
> Capabilities: [e4] CompactPCI hot-swap <?>
> Capabilities: [e8] Vital Product Data
> Unknown small resource type 00, will not decode more.
> Kernel modules: shpchp
>
> 04:09.0 Serial controller: PLX Technology, Inc. PCI9030 32-bit 33MHz PCI <-> IOBus Bridge (prog-if 02 [16550])
> Subsystem: Perle Systems Ltd Device 0041
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 39
> Region 0: Memory at dd901000 (32-bit, non-prefetchable) [size=128]
> Region 1: I/O ports at 7180 [size=128]
> Region 2: I/O ports at 7100 [size=128]
> Kernel driver in use: perle-serial
> Kernel modules: perle_serial
>
> 04:0a.0 Memory controller: Compro Computer Services, Inc. Device 4360 (rev 4d)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 40
> Region 0: Memory at dd900000 (32-bit, non-prefetchable) [size=256]
> Region 1: I/O ports at 7000 [size=256]
> Region 2: Memory at c0000000 (32-bit, non-prefetchable) [size=64M]
> Expansion ROM at dd90a000 [disabled] [size=2K]
> Kernel driver in use: eprm
> Kernel modules: eprm
>
> 05:00.0 Unassigned class [ff00]: Compro Computer Services, Inc. Device 0100 (rev 31)
> Subsystem: Compro Computer Services, Inc. Device 4700
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32
> Interrupt: pin A routed to IRQ 34
> Region 0: Memory at dd80a000 (32-bit, non-prefetchable) [size=4K]
> Region 1: Memory at dd808000 (32-bit, non-prefetchable) [size=8K]
> Region 2: Memory at dd800000 (32-bit, non-prefetchable) [size=32K]
> Region 5: I/O ports at 0000
> Kernel driver in use: iom
> Kernel modules: pciiom
>
> 06:00.0 USB controller: Etron Technology, Inc. EJ168 USB 3.0 Host Controller (rev 01) (prog-if 30 [XHCI])
> Subsystem: Gigabyte Technology Co., Ltd Device 5007
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 37
> Region 0: Memory at de100000 (64-bit, non-prefetchable) [size=32K]
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [70] MSI: Enable+ Count=1/4 Maskable+ 64bit+
> Address: 00000000feeff00c Data: 4183
> Masking: 0000000e Pending: 00000000
> Capabilities: [a0] Express (v2) Endpoint, MSI 00
> DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
> ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <64us
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
> AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
> Capabilities: [190 v1] Device Serial Number 01-01-01-01-01-01-01-01
> Kernel driver in use: xhci_hcd
> Kernel modules: xhci_pci
>
> 07:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9172 SATA 6Gb/s Controller (rev 12) (prog-if 01 [AHCI 1.0])
> Subsystem: Gigabyte Technology Co., Ltd Device b000
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 30
> Region 0: I/O ports at d040 [size=8]
> Region 1: I/O ports at d030 [size=4]
> Region 2: I/O ports at d020 [size=8]
> Region 3: I/O ports at d010 [size=4]
> Region 4: I/O ports at d000 [size=16]
> Region 5: Memory at de010000 (32-bit, non-prefetchable) [size=512]
> Expansion ROM at de000000 [disabled] [size=64K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
> Address: feeff00c Data: 41a2
> Capabilities: [70] Express (v2) Legacy Endpoint, MSI 00
> DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
> AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
> Kernel driver in use: ahci
>
> 08:00.0 PCI bridge: Texas Instruments XIO2000(A)/XIO2200A PCI Express-to-PCI Bridge (rev 03) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Bus: primary=08, secondary=09, subordinate=0d, sec-latency=32
> I/O behind bridge: 0000c000-0000cfff
> Memory behind bridge: d0000000-d87fffff
> Prefetchable memory behind bridge: 00000000c4000000-00000000c6ffffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
> Capabilities: [60] MSI: Enable- Count=1/16 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [80] Subsystem: Device 0000:0000
> Capabilities: [90] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
> DevCap: MaxPayload 512 bytes, PhantFunc 0
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ BrConfRtry-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <16us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
> Kernel modules: shpchp
>
> 09:04.0 PCI bridge: Pericom Semiconductor PCI to PCI Bridge (rev 02) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Bus: primary=09, secondary=0a, subordinate=0d, sec-latency=32
> I/O behind bridge: 0000c000-0000cfff
> Memory behind bridge: d0000000-d87fffff
> Prefetchable memory behind bridge: 00000000c4000000-00000000c6ffffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [b0] Slot ID: 0 slots, First-, chassis 00
> Kernel modules: shpchp
>
> 0a:04.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
> Subsystem: 3Com Corporation 3C905CX-TX/TX-M Fast Etherlink for PC Management NIC
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 42
> Region 0: I/O ports at c200 [size=128]
> Region 1: Memory at d8743000 (32-bit, non-prefetchable) [size=128]
> Expansion ROM at d8700000 [disabled] [size=128K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
> Kernel driver in use: 3c59x
> Kernel modules: 3c59x
>
> 0a:05.0 Network controller: VMIC GE-IP PCI5565,PMC5565 Reflective Memory Node (rev 01)
> Subsystem: PLX Technology, Inc. Device 9656
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 35
> Region 0: Memory at d8742000 (32-bit, non-prefetchable) [size=512]
> Region 1: I/O ports at c100 [size=256]
> Region 2: Memory at d8741000 (32-bit, non-prefetchable) [size=64]
> Region 3: Memory at d0000000 (32-bit, non-prefetchable) [size=128M]
> Capabilities: [40] Power Management version 0
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [48] #00 [0080]
> Kernel driver in use: rfm2g
> Kernel modules: rfm2g
>
> 0a:06.0 PCI bridge: Hint Corp HiNT HB4 PCI-PCI Bridge (PCI6150) (rev 04) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Bus: primary=0a, secondary=0b, subordinate=0b, sec-latency=32
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: d8600000-d86fffff
> Prefetchable memory behind bridge: 00000000c6000000-00000000c6ffffff
> Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
> Capabilities: [e4] CompactPCI hot-swap <?>
> Capabilities: [e8] Vital Product Data
> No end tag found
> Kernel modules: shpchp
>
> 0a:07.0 PCI bridge: Hint Corp HiNT HB4 PCI-PCI Bridge (PCI6150) (rev 04) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Bus: primary=0a, secondary=0c, subordinate=0c, sec-latency=32
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: d8500000-d85fffff
> Prefetchable memory behind bridge: 00000000c5000000-00000000c5ffffff
> Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
> Capabilities: [e4] CompactPCI hot-swap <?>
> Capabilities: [e8] Vital Product Data
> No end tag found
> Kernel modules: shpchp
>
> 0a:08.0 PCI bridge: Hint Corp HiNT HB4 PCI-PCI Bridge (PCI6150) (rev 04) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32, Cache Line Size: 64 bytes
> Bus: primary=0a, secondary=0d, subordinate=0d, sec-latency=32
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: d8400000-d84fffff
> Prefetchable memory behind bridge: 00000000c4000000-00000000c4ffffff
> Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+
> Capabilities: [e4] CompactPCI hot-swap <?>
> Capabilities: [e8] Vital Product Data
> No end tag found
> Kernel modules: shpchp
>
> 0a:09.0 Communication controller: Digi International AccelePort Xr 920 (rev 01)
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin A routed to IRQ 35
> Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=4M]
> Expansion ROM at d8730000 [size=64K]
> Kernel driver in use: dgap
> Kernel modules: dgap
>
> 0a:0a.0 SCSI storage controller: Adaptec AHA-2930CU (rev 03)
> Subsystem: Adaptec Device 3869
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32 (1000ns min, 1000ns max), Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 33
> Region 0: I/O ports at c000 [disabled] [size=256]
> Region 1: Memory at d8740000 (32-bit, non-prefetchable) [size=4K]
> Expansion ROM at d8720000 [disabled] [size=64K]
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: aic7xxx
> Kernel modules: aic7xxx
>
> 0b:00.0 Unassigned class [ff00]: Compro Computer Services, Inc. Device 4710 (rev 41)
> Subsystem: Compro Computer Services, Inc. Device 4710
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32
> Interrupt: pin A routed to IRQ 33
> Region 0: Memory at d8600000 (32-bit, non-prefetchable) [size=512]
> Region 1: Memory at c6000000 (32-bit, prefetchable) [size=16M]
> Capabilities: [80] Vital Product Data
> Unknown small resource type 00, will not decode more.
> Kernel driver in use: gpiohsd
> Kernel modules: gpiohsd
>
> 0c:00.0 Unassigned class [ff00]: Compro Computer Services, Inc. Device 4710 (rev 41)
> Subsystem: Compro Computer Services, Inc. Device 4710
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32
> Interrupt: pin A routed to IRQ 44
> Region 0: Memory at d8500000 (32-bit, non-prefetchable) [size=512]
> Region 1: Memory at c5000000 (32-bit, prefetchable) [size=16M]
> Capabilities: [80] Vital Product Data
> Unknown small resource type 00, will not decode more.
> Kernel driver in use: gpiohsd
> Kernel modules: gpiohsd
>
> 0d:00.0 Unassigned class [ff00]: Compro Computer Services, Inc. Device 4710 (rev 41)
> Subsystem: Compro Computer Services, Inc. Device 4710
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32
> Interrupt: pin A routed to IRQ 42
> Region 0: Memory at d8400000 (32-bit, non-prefetchable) [size=512]
> Region 1: Memory at c4000000 (32-bit, prefetchable) [size=16M]
> Capabilities: [80] Vital Product Data
> Unknown small resource type 00, will not decode more.
> Kernel driver in use: gpiohsd
> Kernel modules: gpiohsd
>
> 0e:00.0 PCI bridge: PLX Technology, Inc. PEX 8114 PCI Express-to-PCI/PCI-X Bridge (rev bc) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Region 0: Memory at ddc00000 (32-bit, non-prefetchable) [size=8K]
> Bus: primary=0e, secondary=0f, subordinate=0f, sec-latency=32
> I/O behind bridge: 0000b000-0000bfff
> Memory behind bridge: ddb00000-ddbfffff
> Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
> Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [40] Power Management version 3
> Flags: PMEClk+ DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [58] PCI-X bridge device
> Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
> Status: Dev=0e:00.0 64bit- 133MHz- SCD- USC- SCO+ SRD-
> Upstream: Capacity=16 CommitmentLimit=16
> Downstream: Capacity=16 CommitmentLimit=16
> Capabilities: [68] Express (v1) PCI-Express to PCI/PCI-X Bridge, MSI 00
> DevCap: MaxPayload 256 bytes, PhantFunc 0
> ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry-
> MaxPayload 128 bytes, MaxReadReq 2048 bytes
> DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq- AuxPwr- TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x4, ASPM L0s L1, Exit Latency L0s <2us, L1 <32us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk-
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt-
> Capabilities: [100 v1] Device Serial Number 00-00-00-01-00-00-0e-df
> Capabilities: [fb4 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
> Capabilities: [138 v1] Power Budgeting <?>
> Capabilities: [148 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
> Status: NegoPending- InProgress-
> Kernel modules: shpchp
>
> 0f:04.0 SCSI storage controller: Adaptec ASC-29320ALP U320 (rev 10)
> Subsystem: Adaptec ASC-29320LPE PCIe U320
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32 (10000ns min, 6250ns max), Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 32
> Region 0: I/O ports at b100 [disabled] [size=256]
> Region 1: Memory at ddb80000 (64-bit, non-prefetchable) [size=8K]
> Region 3: I/O ports at b000 [disabled] [size=256]
> Expansion ROM at ddb00000 [disabled] [size=512K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [a0] MSI: Enable- Count=1/2 Maskable- 64bit+
> Address: 0000000000000000 Data: 0000
> Capabilities: [94] PCI-X non-bridge device
> Command: DPERE- ERO+ RBC=2048 OST=8
> Status: Dev=0f:04.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=8 DMCRS=64 RSCEM- 266MHz- 533MHz-
> Kernel driver in use: aic79xx
> Kernel modules: aic79xx
>
> 10:06.0 Unassigned class [ff00]: Compro Computer Services, Inc. PCI RTOM (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 32
> Interrupt: pin A routed to IRQ 20
> Region 0: I/O ports at a000 [size=64]
> Region 1: Memory at ddf00000 (32-bit, non-prefetchable) [size=4K]
> Kernel driver in use: rtom
> Kernel modules: rtom
>
> 11:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06)
> Subsystem: Gigabyte Technology Co., Ltd Motherboard
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 41
> Region 0: I/O ports at 9000 [size=256]
> Region 2: Memory at c7004000 (64-bit, prefetchable) [size=4K]
> Region 4: Memory at c7000000 (64-bit, prefetchable) [size=16K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
> Address: 00000000feeff00c Data: 41c3
> Capabilities: [70] Express (v2) Endpoint, MSI 01
> DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 4096 bytes
> DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, LTR-, OBFF Not Supported
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
> LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
> Vector table: BAR=4 offset=00000000
> PBA: BAR=4 offset=00000800
> Capabilities: [d0] Vital Product Data
> Unknown small resource type 00, will not decode more.
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
> AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
> Capabilities: [140 v1] Virtual Channel
> Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
> Arb: Fixed- WRR32- WRR64- WRR128-
> Ctrl: ArbSelect=Fixed
> Status: InProgress-
> VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
> Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
> Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
> Status: NegoPending- InProgress-
> Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00
> Kernel driver in use: r8169
> Kernel modules: r8169
>
> 12:00.0 USB controller: Etron Technology, Inc. EJ168 USB 3.0 Host Controller (rev 01) (prog-if 30 [XHCI])
> Subsystem: Gigabyte Technology Co., Ltd Device 5007
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 38
> Region 0: Memory at dde00000 (64-bit, non-prefetchable) [size=32K]
> Capabilities: [50] Power Management version 3
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [70] MSI: Enable+ Count=1/4 Maskable+ 64bit+
> Address: 00000000feeff00c Data: 4193
> Masking: 0000000e Pending: 00000000
> Capabilities: [a0] Express (v2) Endpoint, MSI 00
> DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
> ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ FLReset-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <1us, L1 <64us
> ClockPM+ Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
> AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
> Capabilities: [190 v1] Device Serial Number 01-01-01-01-01-01-01-01
> Kernel driver in use: xhci_hcd
> Kernel modules: xhci_pci
>
> 13:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9172 SATA 6Gb/s Controller (rev 12) (prog-if 01 [AHCI 1.0])
> Subsystem: Gigabyte Technology Co., Ltd Device b000
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 31
> Region 0: I/O ports at 8040 [size=8]
> Region 1: I/O ports at 8030 [size=4]
> Region 2: I/O ports at 8020 [size=8]
> Region 3: I/O ports at 8010 [size=4]
> Region 4: I/O ports at 8000 [size=16]
> Region 5: Memory at ddd10000 (32-bit, non-prefetchable) [size=512]
> Expansion ROM at ddd00000 [disabled] [size=64K]
> Capabilities: [40] Power Management version 3
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit-
> Address: feeff00c Data: 41c2
> Capabilities: [70] Express (v2) Legacy Endpoint, MSI 00
> DevCap: MaxPayload 512 bytes, PhantFunc 0, Latency L0s <1us, L1 <8us
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr- TransPend-
> LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us
> ClockPM- Surprise- LLActRep- BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
> DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
> LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
> Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
> Compliance De-emphasis: -6dB
> LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
> EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
> Capabilities: [100 v1] Advanced Error Reporting
> UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
> AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
> Kernel driver in use: ahci
>
next prev parent reply other threads:[~2016-01-14 0:05 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-01-12 21:37 Can't boot new 4.4 kernel with IOMMU enabled Mark Hounschell
[not found] ` <56957209.1080202-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-01-13 3:09 ` Baoquan He
[not found] ` <20160113030950.GB11902-0VdLhd/A9PlfpSRLqpFUpR/sF2h8X+2i0E9HWUfgJXw@public.gmane.org>
2016-01-13 14:42 ` Mark Hounschell
[not found] ` <56966244.80700-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-01-14 0:05 ` Baoquan He [this message]
[not found] ` <20160114000520.GA2449-ejN7fcUYdH/by3iVrkZq2A@public.gmane.org>
2016-01-14 14:04 ` Mark Hounschell
[not found] ` <5697AAD8.1000105-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-01-20 15:38 ` Joerg Roedel
[not found] ` <20160120153823.GG18805-zLv9SwRftAIdnm+yROfE0A@public.gmane.org>
2016-01-20 15:46 ` Joerg Roedel
[not found] ` <20160120154658.GH18805-zLv9SwRftAIdnm+yROfE0A@public.gmane.org>
2016-01-20 16:04 ` Mark Hounschell
[not found] ` <569FB013.4050709-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-01-20 16:19 ` Joerg Roedel
[not found] ` <20160120161904.GI18805-zLv9SwRftAIdnm+yROfE0A@public.gmane.org>
2016-01-20 18:19 ` Mark Hounschell
[not found] ` <569FCFC8.2000606-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-01-20 18:26 ` Joerg Roedel
[not found] ` <20160120182602.GJ18805-zLv9SwRftAIdnm+yROfE0A@public.gmane.org>
2016-01-20 19:32 ` Mark Hounschell
[not found] ` <569FE0B0.4030902-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-01-20 20:30 ` Joerg Roedel
2016-01-21 14:50 ` Mark Hounschell
[not found] ` <56A0F03C.8010109-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-01-21 14:58 ` Mark Hounschell
[not found] ` <56A0F221.10502-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-01-21 22:39 ` Joerg Roedel
[not found] ` <20160121223958.GL18805-zLv9SwRftAIdnm+yROfE0A@public.gmane.org>
2016-02-02 15:49 ` Mark Hounschell
[not found] ` <56B0CFF7.80907-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-02-16 16:24 ` Joerg Roedel
[not found] ` <20160216162455.GX18805-zLv9SwRftAIdnm+yROfE0A@public.gmane.org>
2016-02-16 17:32 ` Mark Hounschell
[not found] ` <56C35D1A.9080307-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-02-26 16:23 ` Joerg Roedel
[not found] ` <20160226162319.GH22747-zLv9SwRftAIdnm+yROfE0A@public.gmane.org>
2016-02-26 19:20 ` Mark Hounschell
[not found] ` <56D0A565.8080406-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-02-29 17:42 ` Joerg Roedel
[not found] ` <20160229174252.GN22747-zLv9SwRftAIdnm+yROfE0A@public.gmane.org>
2016-02-29 17:52 ` Mark Hounschell
[not found] ` <56D48560.4010904-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-03-18 17:24 ` Mark Hounschell
[not found] ` <56EC39CB.2010909-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-04-11 13:54 ` Joerg Roedel
[not found] ` <20160411135451.GO17838-zLv9SwRftAIdnm+yROfE0A@public.gmane.org>
2016-04-11 14:59 ` Mark Hounschell
[not found] ` <570BBBE4.9040307-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-04-11 15:43 ` Joerg Roedel
2016-01-20 15:56 ` Mark Hounschell
2016-01-20 12:31 ` Joerg Roedel
[not found] ` <20160120123116.GF18805-zLv9SwRftAIdnm+yROfE0A@public.gmane.org>
2016-01-20 13:03 ` Mark Hounschell
[not found] ` <569F858E.4060701-n2QNKt385d+sTnJN9+BGXg@public.gmane.org>
2016-01-20 13:18 ` Baoquan He
2016-01-20 13:03 ` Baoquan He
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160114000520.GA2449@x1.redhat.com \
--to=bhe-h+wxahxf7alqt0dzr+alfa@public.gmane.org \
--cc=iommu-cunTk1MwBs9QetFLy7KEm3xJsTq8ys+cHZ5vskTnxNA@public.gmane.org \
--cc=markh-n2QNKt385d+sTnJN9+BGXg@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.