From: stephen@networkplumber.org (Stephen Hemminger)
Subject: NVM and swap device
Date: Fri, 15 Jan 2016 10:20:52 -0800 [thread overview]
Message-ID: <20160115102052.0091a976@xeon-e3> (raw)
In-Reply-To: <20160115174236.GC11165@localhost.localdomain>
On Fri, 15 Jan 2016 17:42:36 +0000
Keith Busch <keith.busch@intel.com> wrote:
> On Tue, Jan 12, 2016@07:40:30PM -0800, Stephen Hemminger wrote:
> > I have a nice shiny new Intel NVM PCI card; decided to use it for a filesystem and swap.
> > The filesystem (btrfs) is doing fine, but the swap device was throwing occasional
> > random errors. Suspect a driver problem rather than hardware.
> >
> > I am using 4.4 kernel without patches.
> >
> > kern.log:Jan 12 08:11:57 xeon-e3 kernel: [159474.037390] Read-error on swap-device (259:0:17597808)
> > kern.log.1:Jan 7 08:32:10 xeon-e3 kernel: [87938.855526] Read-error on swap-device (259:0:11355648)
> > kern.log.1:Jan 7 08:32:10 xeon-e3 kernel: [87938.855530] Read-error on swap-device (259:0:11355656)
> > kern.log.1:Jan 7 08:32:10 xeon-e3 kernel: [87939.855467] Read-error on swap-device (259:0:16180824)
> > kern.log.1:Jan 8 08:24:07 xeon-e3 kernel: [63670.777981] Read-error on swap-device (259:0:32690768)
> > kern.log.1:Jan 9 09:25:02 xeon-e3 kernel: [153720.919325] Read-error on swap-device (259:0:220488)
> > kern.log.1:Jan 9 16:40:05 xeon-e3 kernel: [179820.957675] Read-error on swap-device (259:0:24476232)
> > kern.log.1:Jan 9 16:40:05 xeon-e3 kernel: [179820.962673] Read-error on swap-device (259:0:33292816)
> >
> > The swap device was being added via /etc/fstab by UUID.
>
> If you haven't any further insights into the issue, could you check the
> device's health? I'd be surprised if there is a problem with that since
> you mentioned it was new card, but would like to rule that out if this
> has hit a dead end on the other testing.
>
> For that, we need smart logs. There are various tools available that
> can read those logs. Here's an open source version:
>
> https://github.com/linux-nvme/nvme-cli
>
> Here's example output from one of my drives with the above tool:
>
> # nvme smart-log /dev/nvme0
> Smart Log for NVME device:/dev/nvme0 namespace-id:ffffffff
> critical_warning : 0
> temperature : 29 C
> available_spare : 100%
> available_spare_threshold : 10%
> percentage_used : 0%
> data_units_read : 577,600
> data_units_written : 3,182,404
> host_read_commands : 4,537,801
> host_write_commands : 18,713,235
> controller_busy_time : 17
> power_cycles : 1
> power_on_hours : 163
> unsafe_shutdowns : 1
> media_errors : 0
> num_err_log_entries : 0
Are these logs persistant?
# ./nvme smart-log /dev/nvme0
Smart Log for NVME device:/dev/nvme0 namespace-id:ffffffff
critical_warning : 0
temperature : 29 C
available_spare : 100%
available_spare_threshold : 10%
percentage_used : 0%
data_units_read : 2,768,267
data_units_written : 4,085,497
host_read_commands : 74,458,451
host_write_commands : 68,420,945
controller_busy_time : 12
power_cycles : 33
power_on_hours : 227
unsafe_shutdowns : 6
media_errors : 0
num_err_log_entries : 0
Critical Composite Temperature Time : 0
Temperature Sensor 1 : 0 C
Temperature Sensor 2 : 0 C
Temperature Sensor 3 : 0 C
Temperature Sensor 4 : 0 C
Temperature Sensor 5 : 0 C
Temperature Sensor 6 : 0 C
Temperature Sensor 7 : 0 C
Temperature Sensor 8 : 0 C
next prev parent reply other threads:[~2016-01-15 18:20 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-01-13 3:40 NVM and swap device Stephen Hemminger
2016-01-13 8:26 ` Hannes Reinecke
2016-01-13 15:13 ` Matthew Wilcox
2016-01-13 17:47 ` Jens Axboe
2016-01-13 18:51 ` Stephen Hemminger
2016-01-13 18:55 ` Jens Axboe
2016-01-20 21:30 ` Stephen Hemminger
2016-01-15 17:42 ` Keith Busch
2016-01-15 18:18 ` Stephen Hemminger
2016-01-15 18:20 ` Stephen Hemminger [this message]
2016-01-15 21:19 ` Keith Busch
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160115102052.0091a976@xeon-e3 \
--to=stephen@networkplumber.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.