[U-Boot] [PATCH v1] arm: imx: Add support for GE Bx50v3 boards

[Peng Fan <van.freenix@gmail.com>]

Hi Akshay,

CC i.MX maintainer Stefano for you.

On Wed, Jan 27, 2016 at 05:53:47PM -0500, Akshay Bhat wrote:
>Add support for GE B450v3, B650v3 and B850v3 boards. The boards
>are based on Advantech BA16 module which has a imx6 processor.

Which imx6 processor?

>The boards support:
> - FEC Ethernet
> - USB Ports
> - SDHC and MMC boot
> - SPI NOR
> - LVDS and HDMI display
>
>Basic information about the module:
> - Module manufacturer: Advantech
> - CPU: Freescale ARM Cortex-A9 i.MX6
> - SPECS:
>     Up to 2GB Onboard DDR3 Memory;
>     Up to 16GB Onboard eMMC NAND Flash
>     Supports OpenGL ES 2.0 and OpenVG 1.1
>     HDMI, 24-bit LVDS
>     1x UART, 2x I2C, 8x GPIO,
>     4x Host USB 2.0 port, 1x USB OTG port,
>     1x micro SD (SDHC),1x SDIO, 1x SATA II,
>     1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
>
>Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
>---
>
> arch/arm/cpu/armv7/mx6/Kconfig |  10 +
> board/ge/bx50v3/Kconfig        |  15 ++
> board/ge/bx50v3/MAINTAINERS    |   8 +
> board/ge/bx50v3/Makefile       |   8 +
> board/ge/bx50v3/bx50v3.c       | 534 +++++++++++++++++++++++++++++++++++++++++
> board/ge/bx50v3/bx50v3.cfg     | 151 ++++++++++++
> configs/ge_b450v3_defconfig    |   9 +
> configs/ge_b650v3_defconfig    |   9 +
> configs/ge_b850v3_defconfig    |   9 +
> include/configs/ge_bx50v3.h    | 374 +++++++++++++++++++++++++++++
> 10 files changed, 1127 insertions(+)
> create mode 100644 board/ge/bx50v3/Kconfig
> create mode 100644 board/ge/bx50v3/MAINTAINERS
> create mode 100644 board/ge/bx50v3/Makefile
> create mode 100644 board/ge/bx50v3/bx50v3.c
> create mode 100644 board/ge/bx50v3/bx50v3.cfg
> create mode 100644 configs/ge_b450v3_defconfig
> create mode 100644 configs/ge_b650v3_defconfig
> create mode 100644 configs/ge_b850v3_defconfig
> create mode 100644 include/configs/ge_bx50v3.h
>
>diff --git a/arch/arm/cpu/armv7/mx6/Kconfig b/arch/arm/cpu/armv7/mx6/Kconfig
>index 8489182..c4e89f1 100644
>--- a/arch/arm/cpu/armv7/mx6/Kconfig
>+++ b/arch/arm/cpu/armv7/mx6/Kconfig
>@@ -60,6 +60,15 @@ config TARGET_CM_FX6
> config TARGET_EMBESTMX6BOARDS
> 	bool "embestmx6boards"
> 
>+config TARGET_GE_B450V3
>+	bool "General Electric B450v3"
>+
>+config TARGET_GE_B650V3
>+	bool "General Electric B650v3"
>+
>+config TARGET_GE_B850V3
>+	bool "General Electric B850v3"
>+
> config TARGET_GW_VENTANA
> 	bool "gw_ventana"
> 	select SUPPORT_SPL
>@@ -153,6 +162,7 @@ endchoice
> config SYS_SOC
> 	default "mx6"
> 
>+source "board/ge/bx50v3/Kconfig"
> source "board/aristainetos/Kconfig"
> source "board/bachmann/ot1200/Kconfig"
> source "board/barco/platinum/Kconfig"
>diff --git a/board/ge/bx50v3/Kconfig b/board/ge/bx50v3/Kconfig
>new file mode 100644
>index 0000000..2c4a689
>--- /dev/null
>+++ b/board/ge/bx50v3/Kconfig
>@@ -0,0 +1,15 @@
>+if TARGET_GE_B450V3 || TARGET_GE_B650V3 || TARGET_GE_B850V3
>+
>+config SYS_BOARD
>+	default "bx50v3"
>+
>+config SYS_VENDOR
>+	default "ge"
>+
>+config SYS_SOC
>+	default "mx6"
>+
>+config SYS_CONFIG_NAME
>+	default "ge_bx50v3"
>+
>+endif
>diff --git a/board/ge/bx50v3/MAINTAINERS b/board/ge/bx50v3/MAINTAINERS
>new file mode 100644
>index 0000000..8e60791
>--- /dev/null
>+++ b/board/ge/bx50v3/MAINTAINERS
>@@ -0,0 +1,8 @@
>+GE_BX50V3 BOARD
>+M:	Martin Donnelly <martin.donnelly@ge.com>
>+S:	Maintained
>+F:	board/ge/bx50v3/
>+F:	include/configs/ge_bx50v3.h
>+F:	configs/ge_b450v3_defconfig
>+F:	configs/ge_b650v3_defconfig
>+F:	configs/ge_b850v3_defconfig
>diff --git a/board/ge/bx50v3/Makefile b/board/ge/bx50v3/Makefile
>new file mode 100644
>index 0000000..bcd149f
>--- /dev/null
>+++ b/board/ge/bx50v3/Makefile
>@@ -0,0 +1,8 @@
>+#
>+# Copyright 2015 Timesys Corporation
>+# Copyright 2015 General Electric Company
>+#
>+# SPDX-License-Identifier:	GPL-2.0+
>+#
>+
>+obj-y  := bx50v3.o
>diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c
>new file mode 100644
>index 0000000..42035be
>--- /dev/null
>+++ b/board/ge/bx50v3/bx50v3.c
>@@ -0,0 +1,534 @@
>+/*
>+ * Copyright 2015 Timesys Corporation
>+ * Copyright 2015 General Electric Company
>+ * Copyright 2012 Freescale Semiconductor, Inc.
>+ *
>+ * SPDX-License-Identifier:	GPL-2.0+
>+ */
>+
>+#include <asm/arch/clock.h>
>+#include <asm/arch/imx-regs.h>
>+#include <asm/arch/iomux.h>
>+#include <asm/arch/mx6-pins.h>
>+#include <asm/errno.h>
>+#include <asm/gpio.h>
>+#include <asm/imx-common/mxc_i2c.h>
>+#include <asm/imx-common/iomux-v3.h>
>+#include <asm/imx-common/boot_mode.h>
>+#include <asm/imx-common/video.h>
>+#include <mmc.h>
>+#include <fsl_esdhc.h>
>+#include <miiphy.h>
>+#include <netdev.h>
>+#include <asm/arch/mxc_hdmi.h>
>+#include <asm/arch/crm_regs.h>
>+#include <asm/io.h>
>+#include <asm/arch/sys_proto.h>
>+#include <i2c.h>
>+DECLARE_GLOBAL_DATA_PTR;
>+
>+#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
>+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
>+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
>+
>+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
>+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
>+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
>+
>+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |	\
>+	PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
>+
>+#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \
>+	PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST)
>+
>+#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
>+	PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
>+
>+#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
>+		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
>+
>+#define I2C_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
>+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
>+	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
>+
>+#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
>+
>+int dram_init(void)
>+{
>+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
>+
>+	return 0;
>+}
>+
>+iomux_v3_cfg_t const uart3_pads[] = {

Use static.

>+	MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
>+	MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
>+	MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
>+	MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
>+};
>+
>+iomux_v3_cfg_t const uart4_pads[] = {

Ditto. Also the following iomux definitions.

>+	MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
>+	MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
>+};
>+
>+iomux_v3_cfg_t const enet_pads[] = {
>+	MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
>+	MX6_PAD_ENET_MDC__ENET_MDC   | MUX_PAD_CTRL(ENET_PAD_CTRL),
>+	MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
>+	MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>+	MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>+	MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>+	MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
>+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
>+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK  | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
>+	MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>+	MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>+	MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>+	MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>+	MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
>+	/* AR8033 PHY Reset */
>+	MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
>+};
>+
>+static void setup_iomux_enet(void)
>+{
>+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
>+
>+	/* Reset AR8033 PHY */
>+	gpio_direction_output(IMX_GPIO_NR(1, 28), 0);
>+	udelay(500);
>+	gpio_set_value(IMX_GPIO_NR(1, 28), 1);
>+}
>+
>+iomux_v3_cfg_t const usdhc2_pads[] = {
>+	MX6_PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD2_DAT0__SD2_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD2_DAT1__SD2_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD2_DAT2__SD2_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD2_DAT3__SD2_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_GPIO_4__GPIO1_IO04	| MUX_PAD_CTRL(NO_PAD_CTRL),
>+};
>+
>+iomux_v3_cfg_t const usdhc3_pads[] = {
>+	MX6_PAD_SD3_CLK__SD3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD3_CMD__SD3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+};
>+
>+iomux_v3_cfg_t const usdhc4_pads[] = {
>+	MX6_PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
>+	MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
>+	MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
>+};
>+
>+iomux_v3_cfg_t const ecspi1_pads[] = {
>+	MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
>+	MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
>+	MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
>+	MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
>+};
>+
>+static struct i2c_pads_info i2c_pad_info1 = {
>+	.scl = {
>+		.i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
>+		.gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD,
>+		.gp = IMX_GPIO_NR(5, 27)
>+	},
>+	.sda = {
>+		.i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD,
>+		.gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD,
>+		.gp = IMX_GPIO_NR(5, 26)
>+	}
>+};
>+
>+static struct i2c_pads_info i2c_pad_info2 = {
>+	.scl = {
>+		.i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
>+		.gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
>+		.gp = IMX_GPIO_NR(4, 12)
>+	},
>+	.sda = {
>+		.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
>+		.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
>+		.gp = IMX_GPIO_NR(4, 13)
>+	}
>+};
>+
>+static struct i2c_pads_info i2c_pad_info3 = {
>+	.scl = {
>+		.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD,
>+		.gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD,
>+		.gp = IMX_GPIO_NR(1, 3)
>+	},
>+	.sda = {
>+		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
>+		.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
>+		.gp = IMX_GPIO_NR(1, 6)
>+	}
>+};
>+
>+#ifdef CONFIG_MXC_SPI
>+int board_spi_cs_gpio(unsigned bus, unsigned cs)
>+{
>+	return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1;
>+}
>+
>+static void setup_spi(void)
>+{
>+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
>+}
>+#endif
>+
>+iomux_v3_cfg_t const pcie_pads[] = {
>+	MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
>+	MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
>+};
>+
>+static void setup_pcie(void)
>+{
>+	imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
>+}
>+
>+static void setup_iomux_uart(void)
>+{
>+	imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
>+	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
>+}
>+
>+#ifdef CONFIG_FSL_ESDHC
>+struct fsl_esdhc_cfg usdhc_cfg[3] = {
>+	{USDHC2_BASE_ADDR},
>+	{USDHC3_BASE_ADDR},
>+	{USDHC4_BASE_ADDR},
>+};
>+
>+#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
>+#define USDHC4_CD_GPIO	IMX_GPIO_NR(6, 11)
>+
>+int board_mmc_getcd(struct mmc *mmc)
>+{
>+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
>+	int ret = 0;
>+
>+	switch (cfg->esdhc_base) {
>+	case USDHC2_BASE_ADDR:
>+		ret = !gpio_get_value(USDHC2_CD_GPIO);
>+		break;
>+	case USDHC3_BASE_ADDR:
>+		ret = 1; /* eMMC/uSDHC4 is always present */

uSDHC4->uSDHC3?

>+		break;
>+	case USDHC4_BASE_ADDR:
>+		ret = !gpio_get_value(USDHC4_CD_GPIO);
>+		break;
>+	}
>+
>+	return ret;
>+}
>+
>+int board_mmc_init(bd_t *bis)
>+{
>+	int ret;
>+	int i;
>+
>+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
>+		switch (i) {
>+		case 0:
>+			imx_iomux_v3_setup_multiple_pads(
>+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
>+			gpio_direction_input(USDHC2_CD_GPIO);
>+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
>+			break;
>+		case 1:
>+			imx_iomux_v3_setup_multiple_pads(
>+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
>+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
>+			break;
>+		case 2:
>+			imx_iomux_v3_setup_multiple_pads(
>+				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
>+			gpio_direction_input(USDHC4_CD_GPIO);
>+			usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
>+			break;
>+		default:
>+			printf("Warning: you configured more USDHC controllers\n"
>+			       "(%d) then supported by the board (%d)\n",
>+			       i + 1, CONFIG_SYS_FSL_USDHC_NUM);
>+			return -EINVAL;
>+		}
>+
>+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
>+		if (ret)
>+			return ret;
>+	}
>+
>+	return 0;
>+}
>+#endif
>+
>+int mx6_rgmii_rework(struct phy_device *phydev)

static

>+{
>+	/* Configure AR8033 to ouput a 125MHz clk from CLK_25M */
>+	/* set device address 0x7 */
>+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
>+	/* offset 0x8016: CLK_25M Clock Select */
>+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
>+	/* enable register write, no post increment, address 0x7 */
>+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
>+	/* set to 125 MHz from local PLL source */
>+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18);
>+
>+	/* rgmii tx clock delay enable */
>+	/* set debug port address: SerDes Test and System Mode Control */
>+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
>+	/* enable rgmii tx clock delay */
>+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
>+
>+	return 0;
>+}
>+
>+int board_phy_config(struct phy_device *phydev)
>+{
>+	mx6_rgmii_rework(phydev);
>+
>+	if (phydev->drv->config)
>+		phydev->drv->config(phydev);
>+
>+	return 0;
>+}
>+
>+#if defined(CONFIG_VIDEO_IPUV3)
>+static iomux_v3_cfg_t const backlight_pads[] = {
>+	/* Power for LVDS Display */
>+	MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
>+#define LVDS_POWER_GP IMX_GPIO_NR(3, 22)
>+	/* Backlight enable for LVDS display */
>+	MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
>+#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0)
>+};
>+
>+static void do_enable_hdmi(struct display_info_t const *dev)
>+{
>+	imx_enable_hdmi_phy();
>+}
>+
>+int board_cfb_skip(void)
>+{
>+	gpio_direction_output(LVDS_POWER_GP, 1);
>+
>+	return 0;
>+}
>+
>+static int detect_baseboard(struct display_info_t const *dev)
>+{
>+#if (defined CONFIG_TARGET_GE_B450V3 || defined CONFIG_TARGET_GE_B650V3)

        if (IS_ENABLED(CONFIG_TARGET_GE_B450V3) || IS_ENABLED(CONFIG_TARGET_GE_B650V3))
		return 1;

	return 0;

>+	return 1;
>+#else
>+	return 0;
>+#endif
>+}
>+
>+struct display_info_t const displays[] = {{
>+	.bus	= -1,
>+	.addr	= -1,
>+	.pixfmt	= IPU_PIX_FMT_RGB24,
>+	.detect	= detect_baseboard,
>+	.enable	= NULL,
>+	.mode	= {
>+		.name           = "G121X1-L03",
>+		.refresh        = 60,
>+		.xres           = 1024,
>+		.yres           = 768,
>+		.pixclock       = 15385,
>+		.left_margin    = 20,
>+		.right_margin   = 300,
>+		.upper_margin   = 30,
>+		.lower_margin   = 8,
>+		.hsync_len      = 1,
>+		.vsync_len      = 1,
>+		.sync           = FB_SYNC_EXT,
>+		.vmode          = FB_VMODE_NONINTERLACED
>+} }, {
>+	.bus	= -1,
>+	.addr	= 3,
>+	.pixfmt	= IPU_PIX_FMT_RGB24,
>+	.detect	= detect_hdmi,
>+	.enable	= do_enable_hdmi,
>+	.mode	= {
>+		.name           = "HDMI",
>+		.refresh        = 60,
>+		.xres           = 1024,
>+		.yres           = 768,
>+		.pixclock       = 15385,
>+		.left_margin    = 220,
>+		.right_margin   = 40,
>+		.upper_margin   = 21,
>+		.lower_margin   = 7,
>+		.hsync_len      = 60,
>+		.vsync_len      = 10,
>+		.sync           = FB_SYNC_EXT,
>+		.vmode          = FB_VMODE_NONINTERLACED
>+} } };
>+size_t display_count = ARRAY_SIZE(displays);
>+
>+static void setup_display(void)
>+{
>+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
>+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
>+	int reg;
>+
>+	enable_ipu_clock();
>+	imx_setup_hdmi();
>+
>+	reg = readl(&mxc_ccm->CCGR3);
>+	reg |=  MXC_CCM_CCGR3_LDB_DI0_MASK;
>+	writel(reg, &mxc_ccm->CCGR3);
>+
>+	reg = readl(&mxc_ccm->cs2cdr);
>+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK |
>+		 MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
>+	reg |= (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) |
>+	       (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
>+	writel(reg, &mxc_ccm->cs2cdr);
>+
>+	reg = readl(&mxc_ccm->cscmr2);
>+	reg |= (MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
>+	writel(reg, &mxc_ccm->cscmr2);
>+
>+	reg = readl(&mxc_ccm->chsccdr);
>+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
>+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
>+	writel(reg, &mxc_ccm->chsccdr);
>+
>+	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
>+	     | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
>+	     | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
>+	     | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
>+	     | IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT
>+	     | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
>+	     | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
>+	     | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0
>+	     | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
>+	writel(reg, &iomux->gpr[2]);
>+
>+	reg = readl(&iomux->gpr[3]);
>+	reg = (reg & ~(IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
>+		       IOMUXC_GPR3_LVDS1_MUX_CTL_MASK |
>+		       IOMUXC_GPR3_HDMI_MUX_CTL_MASK))
>+	    | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
>+	       << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET)
>+	    | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
>+	       << IOMUXC_GPR3_LVDS1_MUX_CTL_OFFSET);
>+	writel(reg, &iomux->gpr[3]);
>+
>+	/* backlights off until needed */
>+	imx_iomux_v3_setup_multiple_pads(backlight_pads,
>+					 ARRAY_SIZE(backlight_pads));
>+	gpio_direction_input(LVDS_POWER_GP);
>+	gpio_direction_input(LVDS_BACKLIGHT_GP);
>+}
>+#endif /* CONFIG_VIDEO_IPUV3 */
>+
>+/*
>+ * Do not overwrite the console
>+ * Use always serial for U-Boot console
>+ */
>+int overwrite_console(void)
>+{
>+	return 1;
>+}
>+
>+int board_eth_init(bd_t *bis)
>+{
>+	setup_iomux_enet();
>+	setup_pcie();
>+
>+	return cpu_eth_init(bis);
>+}
>+
>+iomux_v3_cfg_t const misc_pads[] = {
>+	MX6_PAD_KEY_ROW2__GPIO4_IO11	| MUX_PAD_CTRL(NO_PAD_CTRL),
>+};
>+#define SUS_S3_OUT	IMX_GPIO_NR(4, 11)
>+#define WIFI_EN	IMX_GPIO_NR(6, 14)
>+
>+int board_early_init_f(void)
>+{
>+	imx_iomux_v3_setup_multiple_pads(misc_pads,
>+					 ARRAY_SIZE(misc_pads));
>+	gpio_direction_output(SUS_S3_OUT, 1);
>+	gpio_direction_output(WIFI_EN, 1);

Move the upper two line to board_init.

>+
>+	setup_iomux_uart();
>+#if defined(CONFIG_VIDEO_IPUV3)
>+	setup_display();
>+#endif

Move to board_init.

>+
>+	return 0;
>+}
>+
>+int board_init(void)
>+{
>+	/* address of boot parameters */
>+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
>+
>+#ifdef CONFIG_MXC_SPI
>+	setup_spi();
>+#endif
>+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
>+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
>+	setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
>+
>+	return 0;
>+}
>+
>+#ifdef CONFIG_CMD_BMODE
>+static const struct boot_mode board_boot_modes[] = {
>+	/* 4 bit bus width */
>+	{"sd2",	 MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
>+	{"sd3",	 MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
>+	/* 8 bit bus width */
>+	{"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},

I guess 0x38 should be changed to 0x58?

>+	{NULL,	 0},
>+};
>+#endif
>+
>+int board_late_init(void)
>+{
>+#ifdef CONFIG_CMD_BMODE
>+	add_board_boot_modes(board_boot_modes);
>+#endif
>+	/* We need at least 200ms between power on and backlight on
>+	 * as per specifications from CHI MEI */
>+	mdelay(250);
>+
>+	/* Backlight Power */
>+	gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
>+
>+	return 0;
>+}
>+
>+int checkboard(void)
>+{
>+	printf("BOARD: %s\n", CONFIG_BOARD_NAME);
>+	return 0;
>+}
>diff --git a/board/ge/bx50v3/bx50v3.cfg b/board/ge/bx50v3/bx50v3.cfg
>new file mode 100644
>index 0000000..de88769
>--- /dev/null
>+++ b/board/ge/bx50v3/bx50v3.cfg
>@@ -0,0 +1,151 @@
>+/*
>+ *
>+ * Copyright 2015 Timesys Corporation.
>+ * Copyright 2015 General Electric Company
>+ *
>+ * SPDX-License-Identifier:    GPL-2.0+
>+ *
>+ * Refer doc/README.imximage for more details about how-to configure
>+ * and create imximage boot image
>+ *
>+ * The syntax is taken as close as possible with the kwbimage
>+ */
>+
>+IMAGE_VERSION 2
>+BOOT_FROM sd
>+
>+#define __ASSEMBLY__
>+#include <config.h>
>+#include "asm/arch/mx6-ddr.h"
>+#include "asm/arch/iomux.h"
>+#include "asm/arch/crm_regs.h"
>+
>+/* DDR IO */
>+DATA 4, MX6_IOM_GRP_DDR_TYPE,	0x000c0000
>+DATA 4, MX6_IOM_GRP_DDRPKE,	0x00000000
>+DATA 4, MX6_IOM_DRAM_SDCLK_0,	0x00000030
>+DATA 4, MX6_IOM_DRAM_SDCLK_1,	0x00000030
>+DATA 4, MX6_IOM_DRAM_CAS,	0x00000030
>+DATA 4, MX6_IOM_DRAM_RAS,	0x00000030
>+DATA 4, MX6_IOM_GRP_ADDDS,	0x00000030
>+DATA 4, MX6_IOM_DRAM_RESET,	0x00000030
>+DATA 4, MX6_IOM_DRAM_SDBA2,	0x00000000
>+DATA 4, MX6_IOM_DRAM_SDODT0,	0x00000030
>+DATA 4, MX6_IOM_DRAM_SDODT1,	0x00000030
>+DATA 4, MX6_IOM_GRP_CTLDS,	0x00000030
>+DATA 4, MX6_IOM_DDRMODE_CTL,	0x00020000
>+DATA 4, MX6_IOM_DRAM_SDQS0,	0x00000030
>+DATA 4, MX6_IOM_DRAM_SDQS1,	0x00000030
>+DATA 4, MX6_IOM_DRAM_SDQS2,	0x00000030
>+DATA 4, MX6_IOM_DRAM_SDQS3,	0x00000030
>+DATA 4, MX6_IOM_DRAM_SDQS4,	0x00000030
>+DATA 4, MX6_IOM_DRAM_SDQS5,	0x00000030
>+DATA 4, MX6_IOM_DRAM_SDQS6,	0x00000030
>+DATA 4, MX6_IOM_DRAM_SDQS7,	0x00000030
>+DATA 4, MX6_IOM_GRP_DDRMODE,	0x00020000
>+DATA 4, MX6_IOM_GRP_B0DS,	0x00000030
>+DATA 4, MX6_IOM_GRP_B1DS,	0x00000030
>+DATA 4, MX6_IOM_GRP_B2DS,	0x00000030
>+DATA 4, MX6_IOM_GRP_B3DS,	0x00000030
>+DATA 4, MX6_IOM_GRP_B4DS,	0x00000030
>+DATA 4, MX6_IOM_GRP_B5DS,	0x00000030
>+DATA 4, MX6_IOM_GRP_B6DS,	0x00000030
>+DATA 4, MX6_IOM_GRP_B7DS,	0x00000030
>+DATA 4, MX6_IOM_DRAM_DQM0,	0x00000030
>+DATA 4, MX6_IOM_DRAM_DQM1,	0x00000030
>+DATA 4, MX6_IOM_DRAM_DQM2,	0x00000030
>+DATA 4, MX6_IOM_DRAM_DQM3,	0x00000030
>+DATA 4, MX6_IOM_DRAM_DQM4,	0x00000030
>+DATA 4, MX6_IOM_DRAM_DQM5,	0x00000030
>+DATA 4, MX6_IOM_DRAM_DQM6,	0x00000030
>+DATA 4, MX6_IOM_DRAM_DQM7,	0x00000030
>+
>+/* Calibrations */
>+/* ZQ */
>+DATA 4, MX6_MMDC_P0_MPZQHWCTRL,  0xa1390003
>+/* write leveling */
>+DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x001F001F
>+DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x001F001F
>+DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x001F001F
>+DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x001F001F
>+/* Read DQS Gating calibration */
>+DATA 4, MX6_MMDC_P0_MPDGCTRL0,	0x45380544
>+DATA 4, MX6_MMDC_P0_MPDGCTRL1,	0x05280530
>+DATA 4, MX6_MMDC_P1_MPDGCTRL0,	0x4530053C
>+DATA 4, MX6_MMDC_P1_MPDGCTRL1,	0x0530050C
>+/* Read calibration */
>+DATA 4, MX6_MMDC_P0_MPRDDLCTL,	0x36303032
>+DATA 4, MX6_MMDC_P1_MPRDDLCTL,	0x38363042
>+/* Write calibration */
>+DATA 4, MX6_MMDC_P0_MPWRDLCTL,	0x3A3A423E
>+DATA 4, MX6_MMDC_P1_MPWRDLCTL,	0x4A38483E
>+/* read data bit delay */
>+DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
>+DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
>+DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
>+DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
>+DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333
>+DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333
>+DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333
>+DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333
>+
>+/* Complete calibration by forced measurment */
>+DATA 4, MX6_MMDC_P0_MPMUR0,	0x00000800
>+DATA 4, MX6_MMDC_P1_MPMUR0,	0x00000800
>+
>+/* MMDC init */
>+DATA 4, MX6_MMDC_P0_MDPDC,	0x00020036
>+DATA 4, MX6_MMDC_P0_MDOTC,	0x09444040
>+DATA 4, MX6_MMDC_P0_MDCFG0,	0x8A8F79A4
>+DATA 4, MX6_MMDC_P0_MDCFG1,	0xDB538E64
>+DATA 4, MX6_MMDC_P0_MDCFG2,	0x01ff00db
>+DATA 4, MX6_MMDC_P0_MDMISC,	0x00001740
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x00008000
>+DATA 4, MX6_MMDC_P0_MDRWD,	0x000026d2
>+DATA 4, MX6_MMDC_P0_MDOR,	0x008F1023
>+DATA 4, MX6_MMDC_P0_MDASP,	0x00000047
>+DATA 4, MX6_MMDC_P0_MDCTL,	0x841a0000
>+
>+/* Initialize Micron MT41J128M */
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x04088032
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x0408803a
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x00008033
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x0000803b
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x00408031
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x00408039
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x09408030
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x09408038
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x04008040
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x04008048
>+DATA 4, MX6_MMDC_P0_MDREF,	0x00005800
>+DATA 4, MX6_MMDC_P0_MPODTCTRL,	0x00011117
>+DATA 4, MX6_MMDC_P1_MPODTCTRL,	0x00011117
>+DATA 4, MX6_MMDC_P0_MDPDC,	0x00025576
>+DATA 4, MX6_MMDC_P0_MAPSR,	0x00011006
>+DATA 4, MX6_MMDC_P0_MDSCR,	0x00000000
>+
>+/* set the default clock gate to save power */
>+DATA 4, CCM_CCGR0, 0x00C03F3F
>+DATA 4, CCM_CCGR1, 0x0030FC03
>+DATA 4, CCM_CCGR2, 0x0FFFC000
>+DATA 4, CCM_CCGR3, 0x3FF00000
>+DATA 4, CCM_CCGR4, 0x00FFF300
>+DATA 4, CCM_CCGR5, 0x0F0000C3
>+DATA 4, CCM_CCGR6, 0x000003FF
>+
>+/* enable AXI cache for VDOA/VPU/IPU */
>+DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF
>+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
>+DATA 4, MX6_IOMUXC_GPR6, 0x007F007F
>+DATA 4, MX6_IOMUXC_GPR7, 0x007F007F
>+
>+/*
>+ * Setup CCM_CCOSR register as follows:
>+ *
>+ * cko1_en  1	   --> CKO1 enabled
>+ * cko1_div 111  --> divide by 8
>+ * cko1_sel 1011 --> ahb_clk_root
>+ *
>+ * This sets CKO1 at ahb_clk_root/8 132/8 16.5 MHz
>+ */
>+DATA 4, CCM_CCOSR, 0x000000fb
>diff --git a/configs/ge_b450v3_defconfig b/configs/ge_b450v3_defconfig
>new file mode 100644
>index 0000000..21c6280
>--- /dev/null
>+++ b/configs/ge_b450v3_defconfig
>@@ -0,0 +1,9 @@
>+CONFIG_ARM=y
>+CONFIG_ARCH_MX6=y
>+CONFIG_TARGET_GE_B450V3=y
>+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/ge/bx50v3/bx50v3.cfg"
>+# CONFIG_CMD_IMLS is not set
>+# CONFIG_CMD_FLASH is not set
>+CONFIG_CMD_GPIO=y
>+CONFIG_SPI_FLASH=y
>+CONFIG_SPI_FLASH_STMICRO=y
>diff --git a/configs/ge_b650v3_defconfig b/configs/ge_b650v3_defconfig
>new file mode 100644
>index 0000000..6b4d1af
>--- /dev/null
>+++ b/configs/ge_b650v3_defconfig
>@@ -0,0 +1,9 @@
>+CONFIG_ARM=y
>+CONFIG_ARCH_MX6=y
>+CONFIG_TARGET_GE_B650V3=y
>+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/ge/bx50v3/bx50v3.cfg"
>+# CONFIG_CMD_IMLS is not set
>+# CONFIG_CMD_FLASH is not set
>+CONFIG_CMD_GPIO=y
>+CONFIG_SPI_FLASH=y
>+CONFIG_SPI_FLASH_STMICRO=y
>diff --git a/configs/ge_b850v3_defconfig b/configs/ge_b850v3_defconfig
>new file mode 100644
>index 0000000..99bb98b
>--- /dev/null
>+++ b/configs/ge_b850v3_defconfig
>@@ -0,0 +1,9 @@
>+CONFIG_ARM=y
>+CONFIG_ARCH_MX6=y
>+CONFIG_TARGET_GE_B850V3=y
>+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/ge/bx50v3/bx50v3.cfg"

I think you may need to define MX6Q/MX6DL/xx in EXTRA_OPTIONS. Or
you using select MX6x in you Kconfig in arch/arm/cpu/armv7/mx6/Kconfig.

>+# CONFIG_CMD_IMLS is not set
>+# CONFIG_CMD_FLASH is not set
>+CONFIG_CMD_GPIO=y
>+CONFIG_SPI_FLASH=y
>+CONFIG_SPI_FLASH_STMICRO=y
>diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h
>new file mode 100644
>index 0000000..299086d
>--- /dev/null
>+++ b/include/configs/ge_bx50v3.h
>@@ -0,0 +1,374 @@
>+/*
>+ * Copyright (C) 2015 Timesys Corporation
>+ * Copyright (C) 2015 General Electric Company
>+ * Copyright (C) 2014 Advantech
>+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
>+ *
>+ * Configuration settings for the GE MX6Q Bx50v3 boards.
>+ *
>+ * SPDX-License-Identifier:	GPL-2.0+
>+ */
>+
>+#ifndef __GE_BX50V3_CONFIG_H
>+#define __GE_BX50V3_CONFIG_H
>+
>+#include <asm/arch/imx-regs.h>
>+#include <asm/imx-common/gpio.h>
>+
>+#if defined(CONFIG_TARGET_GE_B450V3)
>+#define CONFIG_BOARD_NAME	"General Electric B450v3"
>+#define CONFIG_DEFAULT_FDT_FILE	"/boot/imx6q-b450v3.dtb"
>+#elif defined(CONFIG_TARGET_GE_B650V3)
>+#define CONFIG_BOARD_NAME	"General Electric B650v3"
>+#define CONFIG_DEFAULT_FDT_FILE	"/boot/imx6q-b650v3.dtb"
>+#elif defined(CONFIG_TARGET_GE_B850V3)
>+#define CONFIG_BOARD_NAME	"General Electric B850v3"
>+#define CONFIG_DEFAULT_FDT_FILE	"/boot/imx6q-b850v3.dtb"
>+#else
>+#define CONFIG_BOARD_NAME	"General Electric BA16 Generic"
>+#define CONFIG_DEFAULT_FDT_FILE	"/boot/imx6q-ba16.dtb"
>+#endif
>+
>+#define CONFIG_MXC_UART_BASE	UART3_BASE
>+#define CONFIG_CONSOLE_DEV	"ttymxc2"
>+
>+#define PHYS_SDRAM_SIZE		(2u * 1024 * 1024 * 1024)
>+
>+#define CONFIG_SUPPORT_EMMC_BOOT
>+#define CONFIG_MX6Q
>+
>+#define CONFIG_BOOTDELAY               1
>+
>+#include "mx6_common.h"
>+#include <linux/sizes.h>
>+
>+#define CONFIG_DISPLAY_CPUINFO
>+#define CONFIG_DISPLAY_BOARDINFO
>+
>+#define CONFIG_CMDLINE_TAG
>+#define CONFIG_SETUP_MEMORY_TAGS
>+#define CONFIG_INITRD_TAG
>+#define CONFIG_REVISION_TAG
>+#define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)
>+
>+#define CONFIG_BOARD_EARLY_INIT_F
>+#define CONFIG_BOARD_LATE_INIT
>+
>+#define CONFIG_MXC_GPIO
>+#define CONFIG_MXC_UART
>+
>+#define CONFIG_CMD_FUSE
>+#define CONFIG_MXC_OCOTP
>+
>+/* SATA Configs */
>+#define CONFIG_CMD_SATA
>+#define CONFIG_DWC_AHSATA
>+#define CONFIG_SYS_SATA_MAX_DEVICE	1
>+#define CONFIG_DWC_AHSATA_PORT_ID	0
>+#define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
>+#define CONFIG_LBA48
>+#define CONFIG_LIBATA
>+
>+/* MMC Configs */
>+#define CONFIG_FSL_ESDHC
>+#define CONFIG_FSL_USDHC
>+#define CONFIG_SYS_FSL_ESDHC_ADDR      0
>+#define CONFIG_MMC
>+#define CONFIG_CMD_MMC
>+#define CONFIG_GENERIC_MMC
>+#define CONFIG_BOUNCE_BUFFER
>+#define CONFIG_CMD_EXT2
>+#define CONFIG_CMD_FAT
>+#define CONFIG_DOS_PARTITION
>+
>+/* USB Configs */
>+#define CONFIG_CMD_USB
>+#define CONFIG_CMD_FAT
>+#define CONFIG_USB_EHCI
>+#define CONFIG_USB_EHCI_MX6
>+#define CONFIG_USB_STORAGE
>+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
>+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
>+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
>+#define CONFIG_MXC_USB_FLAGS	0
>+#define CONFIG_USB_KEYBOARD
>+#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
>+
>+#define CONFIG_CI_UDC
>+#define CONFIG_USBD_HS
>+#define CONFIG_USB_GADGET_DUALSPEED
>+#define CONFIG_USB_GADGET
>+#define CONFIG_USB_GADGET_DOWNLOAD
>+#define CONFIG_CMD_USB_MASS_STORAGE
>+#define CONFIG_USB_GADGET_MASS_STORAGE
>+#define CONFIG_USB_FUNCTION_MASS_STORAGE
>+#define CONFIG_USB_GADGET_VBUS_DRAW 2
>+#define CONFIG_G_DNL_VENDOR_NUM   0x0525
>+#define CONFIG_G_DNL_PRODUCT_NUM  0xa4a5
>+#define CONFIG_G_DNL_MANUFACTURER "Advantech"
>+
>+/* Networking Configs */
>+#define CONFIG_CMD_PING
>+#define CONFIG_CMD_DHCP
>+#define CONFIG_CMD_MII
>+#define CONFIG_FEC_MXC
>+#define CONFIG_MII
>+#define IMX_FEC_BASE			ENET_BASE_ADDR
>+#define CONFIG_FEC_XCV_TYPE		RGMII
>+#define CONFIG_ETHPRIME		"FEC"
>+#define CONFIG_FEC_MXC_PHYADDR		4
>+#define CONFIG_PHYLIB
>+#define CONFIG_PHY_ATHEROS
>+
>+/* Serial Flash */
>+#define CONFIG_CMD_SF
>+#ifdef CONFIG_CMD_SF
>+#define CONFIG_MXC_SPI
>+#define CONFIG_SF_DEFAULT_BUS		0
>+#define CONFIG_SF_DEFAULT_CS		0
>+#define CONFIG_SF_DEFAULT_SPEED	20000000
>+#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
>+#endif
>+
>+/* allow to overwrite serial and ethaddr */
>+#define CONFIG_ENV_OVERWRITE
>+#define CONFIG_CONS_INDEX	1
>+#define CONFIG_BAUDRATE	115200
>+
>+/* Command definition */
>+#define CONFIG_CMD_BMODE
>+#define CONFIG_CMD_BOOTZ
>+#undef CONFIG_CMD_IMLS
>+
>+#define CONFIG_LOADADDR	0x12000000
>+#define CONFIG_SYS_TEXT_BASE	0x17800000
>+
>+#define CONFIG_EXTRA_ENV_SETTINGS \
>+	"script=boot.scr\0" \
>+	"image=/boot/uImage\0" \
>+	"uboot=u-boot.imx\0" \
>+	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \

You can take include/configs/mx6sabre_common.h and board/freescale/mx6sabresd/mx6sabresd.c
for reference to runtime setting env.

>+	"fdt_addr=0x18000000\0" \
>+	"boot_fdt=yes\0" \
>+	"ip_dyn=yes\0" \
>+	"console=" CONFIG_CONSOLE_DEV "\0" \
>+	"fdt_high=0xffffffff\0"	  \
>+	"initrd_high=0xffffffff\0" \
>+	"sddev=0\0" \
>+	"emmcdev=1\0" \
>+	"partnum=1\0" \
>+	"update_sd_firmware=" \
>+		"if test ${ip_dyn} = yes; then " \
>+			"setenv get_cmd dhcp; " \
>+		"else " \
>+			"setenv get_cmd tftp; " \
>+		"fi; " \
>+		"if mmc dev ${mmcdev}; then "	\
>+			"if ${get_cmd} ${update_sd_firmware_filename}; then " \
>+				"setexpr fw_sz ${filesize} / 0x200; " \
>+				"setexpr fw_sz ${fw_sz} + 1; "	\
>+				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
>+			"fi; "	\
>+		"fi\0" \
>+	"update_sf_uboot=" \
>+		"if tftp $loadaddr $uboot; then " \
>+			"sf probe; " \
>+			"sf erase 0 0xC0000; " \
>+			"sf write $loadaddr 0x400 $filesize; " \
>+			"echo 'U-Boot upgraded. Please reset'; " \
>+		"fi\0" \
>+	"setargs=setenv bootargs console=${console},${baudrate} " \
>+		"root=/dev/${rootdev} rw rootwait cma=128M\0" \
>+	"loadbootscript=" \
>+		"ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
>+	"bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
>+		" source\0" \
>+	"loadimage=" \
>+		"ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
>+	"loadfdt=ext2load ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
>+	"tryboot=" \
>+		"if run loadbootscript; then " \
>+			"run bootscript; " \
>+		"else " \
>+			"if run loadimage; then " \
>+				"run doboot; " \
>+			"fi; " \
>+		"fi;\0" \
>+	"doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
>+		"run setargs; " \
>+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
>+			"if run loadfdt; then " \
>+				"bootm ${loadaddr} - ${fdt_addr}; " \
>+			"else " \
>+				"if test ${boot_fdt} = try; then " \
>+					"bootm; " \
>+				"else " \
>+					"echo WARN: Cannot load the DT; " \
>+				"fi; " \
>+			"fi; " \
>+		"else " \
>+			"bootm; " \
>+		"fi;\0" \
>+	"netargs=setenv bootargs console=${console},${baudrate} " \
>+		"root=/dev/nfs " \
>+		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
>+	"netboot=echo Booting from net ...; " \
>+		"run netargs; " \
>+		"if test ${ip_dyn} = yes; then " \
>+			"setenv get_cmd dhcp; " \
>+		"else " \
>+			"setenv get_cmd tftp; " \
>+		"fi; " \
>+		"${get_cmd} ${image}; " \
>+		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
>+			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
>+				"bootm ${loadaddr} - ${fdt_addr}; " \
>+			"else " \
>+				"if test ${boot_fdt} = try; then " \
>+					"bootm; " \
>+				"else " \
>+					"echo WARN: Cannot load the DT; " \
>+				"fi; " \
>+			"fi; " \
>+		"else " \
>+			"bootm; " \
>+		"fi;\0" \
>+
>+#define CONFIG_BOOTCOMMAND \
>+	"usb start; " \
>+	"setenv dev usb; " \
>+	"setenv devnum 0; " \
>+	"setenv rootdev sda1; " \
>+	"run tryboot; " \
>+	\
>+	"setenv dev mmc; " \
>+	"setenv rootdev mmcblk0p1; " \
>+	\
>+	"setenv devnum ${sddev}; " \
>+	"if mmc dev ${devnum}; then " \
>+		"run tryboot; " \
>+		"setenv rootdev mmcblk1p1; " \
>+	"fi; " \
>+	\
>+	"setenv devnum ${emmcdev}; " \
>+	"if mmc dev ${devnum}; then " \
>+		"run tryboot; " \
>+	"fi; " \
>+	\
>+	"bmode usb; " \
>+
>+#define CONFIG_ARP_TIMEOUT     200UL
>+
>+/* Miscellaneous configurable options */
>+#define CONFIG_SYS_LONGHELP
>+#define CONFIG_SYS_HUSH_PARSER
>+#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
>+#define CONFIG_AUTO_COMPLETE
>+
>+/* Print Buffer Size */
>+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
>+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
>+
>+#define CONFIG_SYS_MEMTEST_START       0x10000000
>+#define CONFIG_SYS_MEMTEST_END         0x10010000
>+#define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
>+
>+#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
>+
>+#define CONFIG_CMDLINE_EDITING
>+#define CONFIG_STACKSIZE               (128 * 1024)
>+
>+/* Physical Memory Map */
>+#define CONFIG_NR_DRAM_BANKS           1
>+#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
>+
>+#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
>+#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
>+#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
>+
>+#define CONFIG_SYS_INIT_SP_OFFSET \
>+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
>+#define CONFIG_SYS_INIT_SP_ADDR \
>+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
>+
>+/* FLASH and environment organization */
>+#define CONFIG_SYS_NO_FLASH
>+
>+#define CONFIG_ENV_SIZE		(8 * 1024)
>+
>+#define CONFIG_ENV_IS_IN_SPI_FLASH
>+
>+#if defined(CONFIG_ENV_IS_IN_MMC)

You defined CONFIG_ENV_IS_IN_SPI_FLASH. You can drop the CONFIG_ENV_IS_IN_MMC part.

>+#define CONFIG_ENV_OFFSET		(6 * 64 * 1024)
>+#define CONFIG_SYS_MMC_ENV_DEV		1
>+#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
>+#define CONFIG_ENV_OFFSET		(768 * 1024)
>+#define CONFIG_ENV_SECT_SIZE		(64 * 1024)
>+#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
>+#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
>+#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
>+#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
>+#endif
>+
>+#define CONFIG_OF_LIBFDT
>+
>+#ifndef CONFIG_SYS_DCACHE_OFF
>+#define CONFIG_CMD_CACHE
>+#endif
>+
>+#define CONFIG_SYS_FSL_USDHC_NUM	3
>+
>+/* Framebuffer */
>+#define CONFIG_VIDEO
>+#define CONFIG_VIDEO_IPUV3
>+#define CONFIG_CFB_CONSOLE
>+#define CONFIG_VGA_AS_SINGLE_DEVICE
>+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
>+#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
>+#define CONFIG_VIDEO_BMP_RLE8
>+#define CONFIG_SPLASH_SCREEN
>+#define CONFIG_SPLASH_SCREEN_ALIGN
>+#define CONFIG_BMP_16BPP
>+#define CONFIG_VIDEO_LOGO
>+#define CONFIG_VIDEO_BMP_LOGO
>+#define CONFIG_IPUV3_CLK 260000000
>+#define CONFIG_IMX_HDMI
>+#define CONFIG_IMX_VIDEO_SKIP
>+
>+#undef CONFIG_CMD_PCI
>+#ifdef CONFIG_CMD_PCI
>+#define CONFIG_PCI
>+#define CONFIG_PCI_PNP
>+#define CONFIG_PCI_SCAN_SHOW
>+#define CONFIG_PCIE_IMX
>+#define CONFIG_PCIE_IMX_PERST_GPIO	IMX_GPIO_NR(7, 12)
>+#define CONFIG_PCIE_IMX_POWER_GPIO	IMX_GPIO_NR(1, 5)
>+#endif
>+
>+/* I2C Configs */
>+#define CONFIG_CMD_I2C
>+#define CONFIG_SYS_I2C
>+#define CONFIG_SYS_I2C_MXC
>+#define CONFIG_SYS_I2C_SPEED		  100000
>+#define CONFIG_SYS_I2C_MXC_I2C1
>+#define CONFIG_SYS_I2C_MXC_I2C2
>+#define CONFIG_SYS_I2C_MXC_I2C3
>+
>+#ifdef CONFIG_SYS_RECOVERY

I do not find CONFIG_SYS_RECOVERY in uboot upstream code. You may need to drop
it.

Regards,
Peng.
>+#undef CONFIG_BOOTCOMMAND
>+
>+#undef CONFIG_ENV_IS_IN_SPI_FLASH
>+#undef CONFIG_ENV_IS_IN_MMC
>+#define CONFIG_ENV_IS_NOWHERE
>+
>+#define CONFIG_BOOTCOMMAND \
>+	"setenv dev mmc; " \
>+	"setenv devnum ${sddev}; " \
>+	"setenv rootdev mmcblk0p1; " \
>+	"run tryboot; " \
>+	\
>+	"bmode usb; " \
>+
>+#endif /* CONFIG_SYS_RECOVERY */
>+
>+#endif                         /* __GE_BX50V3_CONFIG_H */
>-- 
>2.7.0
>
>
>_______________________________________________
>U-Boot mailing list
>U-Boot at lists.denx.de
>http://lists.denx.de/mailman/listinfo/u-boot
>