Re: [PATCH 10/15] usb: musb: Don't set d+ high before enable for 2430 glue layer

[Bin Liu <b-liu-l0cyMroinI0@public.gmane.org>]

Hi,

On Fri, May 13, 2016 at 02:17:39PM -0700, Tony Lindgren wrote:
> * Bin Liu <b-liu-l0cyMroinI0@public.gmane.org> [160513 14:05]:
> > Hi,
> > 
> > On Wed, May 11, 2016 at 05:53:11PM -0700, Tony Lindgren wrote:
> > > At least 2430 glue layer pulls d+ high on start up even if there are
> > > no gadgets configured. This is bad at least for anything using a separate
> > > battery charger chip as it can confuse the charger detection.
> > > 
> > > Let's fix the issue by getting rid of omap2430_musb_set_mode() and only
> > 
> > By doing so, you lost the feature of switching mode from sysfs, I am not
> > sure if there is anyone using it though, still, it is a regression.
> 
> Oh right, that's a good point.
> 
> How about we change musb_core to call the optional set_mode() if implemented,

The core already does so. Please check musb_core.h.

Regards,
-Bin.

> and then set the session bit in host mode only? That way we can get rid of
> the musb core tinkering in the glue layer drivers eventually?
> 
> > > write session bit in omap2430_musb_enable().
> > 
> > I don't think session bit needs to be set in _enable(), musb_start() in
> > core takes care of this bit.
> 
> OK sounds like that should just work then.
> 
> > > -static int omap2430_musb_set_mode(struct musb *musb, u8 musb_mode)
> > > -{
> > > -	u8	devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
> > > -
> > > -	devctl |= MUSB_DEVCTL_SESSION;
> > > -	musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
> > 
> > In stead of removing it, session bit should only be set when musb_mode
> > == MUSB_HOST, will this fix the D+ pullup problem?
> 
> Good point, I forgot about it being specific to host mode. I'll check.
> 
> > >  static inline void omap2430_low_level_exit(struct musb *musb)
> > >  {
> > >  	u32 l;
> > > @@ -428,6 +418,9 @@ static void omap2430_musb_enable(struct musb *musb)
> > >  
> > >  	case MUSB_VBUS_VALID:
> > >  		omap_control_usb_set_mode(glue->control_otghs, USB_MODE_DEVICE);
> > > +		devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
> > > +		devctl |= MUSB_DEVCTL_SESSION;
> > > +		musb_writeb(musb->mregs, MUSB_DEVCTL, devctl);
> > 
> > session bit is only set for host mode, VBUS_VALID is not a signal for
> > host mode. So you don't have to set the bit here.
> 
> OK thanks.
> 
> Tony
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html