From: Stanislaw Gruszka <sgruszka@redhat.com>
To: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Michal Kazior <michal.kazior@tieto.com>,
ath10k@lists.infradead.org, perry_yuan@dell.com
Subject: ath10k fail to load firmware
Date: Tue, 19 Jul 2016 09:09:33 +0200 [thread overview]
Message-ID: <20160719070932.GA2751@redhat.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 308 bytes --]
Perry from Dell has ath10k device, which do not work with current
linux-firmware. It's on RHEL kernel, however wirelss stack and drivers
are from 4.7-rc1 (I did not update to 4.7 final yet, since I do not see
ath10k fix, which could possibly help here). Partial dmesg is in
the attachment.
Thanks
Stanislaw
[-- Attachment #2: dmesg_ath10k_firmware_error.txt --]
[-- Type: text/plain, Size: 18769 bytes --]
[ 3657.824833] ath10k_pci 0000:01:00.0: irq 127 for MSI/MSI-X
[ 3657.824850] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 3658.026412] ath10k_pci 0000:01:00.0: Direct firmware load failed with error -2
[ 3658.026415] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 3718.215979] ath10k_pci 0000:01:00.0: Direct firmware load failed with error -2
[ 3718.215983] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 3778.377278] ath10k_pci 0000:01:00.0: Direct firmware load failed with error -2
[ 3778.377281] ath10k_pci 0000:01:00.0: Falling back to user helper
[ 3838.538737] ath10k_pci 0000:01:00.0: could not fetch firmware file 'ath10k/QCA6174/hw3.0/firmware-5.bin': -2
[ 3838.539093] ath10k_pci 0000:01:00.0: qca6174 hw3.2 target 0x05030000 chip_id 0x00340aff sub 1028:0310
[ 3838.539096] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 0 testmode 0
[ 3838.539676] ath10k_pci 0000:01:00.0: firmware ver WLAN.RM.2.0-00180-QCARMSWPZ-1 api 4 features wowlan,ignore-otp,no-4addr-pad crc32 75dee6c5
[ 3838.601884] ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=003e,subsystem-vendor=1028,subsystem-device=0310 from ath10k/QCA6174/hw3.0/board-2.bin
[ 3838.601920] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 ed5f849a
[ 3840.719768] ath10k_pci 0000:01:00.0: htt-ver 3.26 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
[ 3840.774653] ath: EEPROM regdomain: 0x6c
[ 3840.774657] ath: EEPROM indicates we should expect a direct regpair map
[ 3840.774659] ath: Country alpha2 being used: 00
[ 3840.774660] ath: Regpair used: 0x6c
[ 3840.806880] IPv6: ADDRCONF(NETDEV_UP): wlp1s0: link is not ready
[ 3846.032903] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 3849.032954] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 3855.033103] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 3860.316236] ath10k_pci 0000:01:00.0: failed to enable dynamic BW: -11
[ 3866.316381] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 3871.595515] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 3874.595587] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 3880.595733] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 3885.878861] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 3888.878966] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 3894.879083] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 3900.159214] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 3903.159290] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 3909.159436] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 3914.441566] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 3917.441639] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 3923.441811] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 3928.721921] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 3931.721989] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 3937.722141] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 3943.006271] ath10k_pci 0000:01:00.0: failed to enable dynamic BW: -11
[ 3949.006419] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 3954.289546] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 3957.289619] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 3963.291067] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 3968.595899] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 3971.595972] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 3977.596123] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 3982.888250] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 3985.888324] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 3991.888474] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 3997.170623] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4000.170679] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4005.673217] usb 1-3: USB disconnect, device number 9
[ 4006.170824] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4011.453957] ath10k_pci 0000:01:00.0: failed to enable dynamic BW: -11
[ 4017.454133] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4022.733233] ath10k_pci 0000:01:00.0: failed to enable adaptive qcs: -11
[ 4028.733380] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4034.014508] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4037.014584] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4043.014732] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4048.297860] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4051.297952] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4057.298086] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4062.582212] ath10k_pci 0000:01:00.0: failed to enable dynamic BW: -11
[ 4068.582368] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4073.866492] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4076.866569] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4082.866730] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4088.145842] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4091.145914] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4097.146076] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4102.427194] ath10k_pci 0000:01:00.0: failed to enable dynamic BW: -11
[ 4108.427367] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4113.708515] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4116.708558] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4122.708698] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4127.986823] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4130.986897] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4136.987045] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4142.269176] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4145.269248] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4151.269508] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4156.549528] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4159.549604] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4165.549748] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4170.829877] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4173.829952] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4179.830102] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4185.110229] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4188.110302] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4194.110449] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4199.390615] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4202.390653] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4208.390800] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4213.671964] ath10k_pci 0000:01:00.0: failed to enable dynamic BW: -11
[ 4219.672080] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4224.951209] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4227.951283] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4233.951430] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4239.231565] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4242.231863] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4248.231786] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4253.512913] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4256.512987] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4262.513152] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4267.794282] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4270.794346] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4276.794486] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4282.077630] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4285.077694] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4291.077838] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4296.356967] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4299.357040] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4305.357187] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4310.637320] ath10k_pci 0000:01:00.0: failed to enable dynamic BW: -11
[ 4316.637467] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4321.917596] ath10k_pci 0000:01:00.0: failed to enable dynamic BW: -11
[ 4327.917742] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4333.198873] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4335.383925] usb 1-3: new high-speed USB device number 10 using xhci_hcd
[ 4335.549396] usb 1-3: New USB device found, idVendor=0930, idProduct=6545
[ 4335.549400] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4335.549403] usb 1-3: Product: TransMemory
[ 4335.549405] usb 1-3: Manufacturer: TOSHIBA
[ 4335.549407] usb 1-3: SerialNumber: C03FD5FBC7ECE020B0006F57
[ 4335.550532] usb-storage 1-3:1.0: USB Mass Storage device detected
[ 4335.552690] scsi host5: usb-storage 1-3:1.0
[ 4336.198950] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4336.555509] scsi 5:0:0:0: Direct-Access TOSHIBA TransMemory PMAP PQ: 0 ANSI: 6
[ 4336.555860] sd 5:0:0:0: Attached scsi generic sg1 type 0
[ 4336.556179] sd 5:0:0:0: [sdd] 30253056 512-byte logical blocks: (15.4 GB/14.4 GiB)
[ 4336.556391] sd 5:0:0:0: [sdd] Write Protect is off
[ 4336.556395] sd 5:0:0:0: [sdd] Mode Sense: 45 00 00 00
[ 4336.556591] sd 5:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4336.610953] sdd: sdd1
[ 4336.612040] sd 5:0:0:0: [sdd] Attached SCSI removable disk
[ 4338.782315] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 4342.199098] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4344.921485] FAT-fs (sdc1): FAT read failed (blocknr 988)
[ 4347.491288] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4350.491331] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4353.447107] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 4356.035732] FAT-fs (sdc1): Directory bread(block 8192) failed
[ 4356.035737] FAT-fs (sdc1): Directory bread(block 8193) failed
[ 4356.035739] FAT-fs (sdc1): Directory bread(block 8194) failed
[ 4356.035741] FAT-fs (sdc1): Directory bread(block 8195) failed
[ 4356.035742] FAT-fs (sdc1): Directory bread(block 8196) failed
[ 4356.035744] FAT-fs (sdc1): Directory bread(block 8197) failed
[ 4356.035745] FAT-fs (sdc1): Directory bread(block 8198) failed
[ 4356.035746] FAT-fs (sdc1): Directory bread(block 8199) failed
[ 4356.035748] FAT-fs (sdc1): Directory bread(block 8200) failed
[ 4356.035749] FAT-fs (sdc1): Directory bread(block 8201) failed
[ 4356.491450] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4360.795098] usb 1-3: USB disconnect, device number 10
[ 4361.772579] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4361.978580] usb 1-3: new high-speed USB device number 11 using xhci_hcd
[ 4362.143504] usb 1-3: New USB device found, idVendor=0930, idProduct=6545
[ 4362.143509] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4362.143511] usb 1-3: Product: TransMemory
[ 4362.143513] usb 1-3: Manufacturer: TOSHIBA
[ 4362.143515] usb 1-3: SerialNumber: C03FD5FBC7ECE020B0006F57
[ 4362.144382] usb-storage 1-3:1.0: USB Mass Storage device detected
[ 4362.144498] scsi host6: usb-storage 1-3:1.0
[ 4363.146215] scsi 6:0:0:0: Direct-Access TOSHIBA TransMemory PMAP PQ: 0 ANSI: 6
[ 4363.146501] sd 6:0:0:0: Attached scsi generic sg1 type 0
[ 4363.147387] sd 6:0:0:0: [sdd] 30253056 512-byte logical blocks: (15.4 GB/14.4 GiB)
[ 4363.147606] sd 6:0:0:0: [sdd] Write Protect is off
[ 4363.147610] sd 6:0:0:0: [sdd] Mode Sense: 45 00 00 00
[ 4363.147824] sd 6:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4363.203504] sdd: sdd1
[ 4363.204555] sd 6:0:0:0: [sdd] Attached SCSI removable disk
[ 4363.386793] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 4364.772651] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4365.018219] FAT-fs (sdc1): FAT read failed (blocknr 988)
[ 4370.772800] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4375.491274] fat__get_entry: 374 callbacks suppressed
[ 4375.491278] FAT-fs (sdc1): Directory bread(block 8192) failed
[ 4375.491283] FAT-fs (sdc1): Directory bread(block 8193) failed
[ 4375.491285] FAT-fs (sdc1): Directory bread(block 8194) failed
[ 4375.491287] FAT-fs (sdc1): Directory bread(block 8195) failed
[ 4375.491289] FAT-fs (sdc1): Directory bread(block 8196) failed
[ 4375.491291] FAT-fs (sdc1): Directory bread(block 8197) failed
[ 4375.491293] FAT-fs (sdc1): Directory bread(block 8198) failed
[ 4375.491295] FAT-fs (sdc1): Directory bread(block 8199) failed
[ 4375.491297] FAT-fs (sdc1): Directory bread(block 8200) failed
[ 4375.491299] FAT-fs (sdc1): Directory bread(block 8201) failed
[ 4376.076929] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[ 4379.077003] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4380.825017] fat__get_entry: 758 callbacks suppressed
[ 4380.825022] FAT-fs (sdc1): Directory bread(block 8192) failed
[ 4380.825025] FAT-fs (sdc1): Directory bread(block 8193) failed
[ 4380.825028] FAT-fs (sdc1): Directory bread(block 8194) failed
[ 4380.825030] FAT-fs (sdc1): Directory bread(block 8195) failed
[ 4380.825042] FAT-fs (sdc1): Directory bread(block 8196) failed
[ 4380.825045] FAT-fs (sdc1): Directory bread(block 8197) failed
[ 4380.825048] FAT-fs (sdc1): Directory bread(block 8198) failed
[ 4380.825051] FAT-fs (sdc1): Directory bread(block 8199) failed
[ 4380.825053] FAT-fs (sdc1): Directory bread(block 8200) failed
[ 4380.825055] FAT-fs (sdc1): Directory bread(block 8201) failed
[ 4381.253552] FAT-fs (sdd1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 4385.077150] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4387.400123] fat__get_entry: 630 callbacks suppressed
[ 4387.400127] FAT-fs (sdc1): Directory bread(block 8192) failed
[ 4387.400131] FAT-fs (sdc1): Directory bread(block 8193) failed
[ 4387.400133] FAT-fs (sdc1): Directory bread(block 8194) failed
[ 4387.400135] FAT-fs (sdc1): Directory bread(block 8195) failed
[ 4387.400138] FAT-fs (sdc1): Directory bread(block 8196) failed
[ 4387.400140] FAT-fs (sdc1): Directory bread(block 8197) failed
[ 4387.400142] FAT-fs (sdc1): Directory bread(block 8198) failed
[ 4387.400144] FAT-fs (sdc1): Directory bread(block 8199) failed
[ 4387.400147] FAT-fs (sdc1): Directory bread(block 8200) failed
[ 4387.400149] FAT-fs (sdc1): Directory bread(block 8201) failed
[ 4390.359284] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4393.359353] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4399.359502] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4404.642633] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4407.642724] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4413.642887] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4414.220306] usb 1-3: USB disconnect, device number 11
[ 4418.959019] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4421.959090] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4427.959209] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4433.257338] ath10k_pci 0000:01:00.0: failed to set rx-chainmask: -11, req 0x3
[ 4436.257470] ath10k_pci 0000:01:00.0: failed to set arp ac override parameter: -11
[ 4438.436778] usb 1-3: new high-speed USB device number 12 using xhci_hcd
[ 4438.601141] usb 1-3: New USB device found, idVendor=0930, idProduct=6545
[ 4438.601145] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4438.601146] usb 1-3: Product: TransMemory
[ 4438.601148] usb 1-3: Manufacturer: TOSHIBA
[ 4438.601149] usb 1-3: SerialNumber: C03FD5FBC7ECE020B0006F57
[ 4438.601617] usb-storage 1-3:1.0: USB Mass Storage device detected
[ 4438.602075] scsi host7: usb-storage 1-3:1.0
[ 4439.604125] scsi 7:0:0:0: Direct-Access TOSHIBA TransMemory PMAP PQ: 0 ANSI: 6
[ 4439.604931] sd 7:0:0:0: Attached scsi generic sg1 type 0
[ 4439.605131] sd 7:0:0:0: [sde] 30253056 512-byte logical blocks: (15.4 GB/14.4 GiB)
[ 4439.605325] sd 7:0:0:0: [sde] Write Protect is off
[ 4439.605329] sd 7:0:0:0: [sde] Mode Sense: 45 00 00 00
[ 4439.605574] sd 7:0:0:0: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 4439.666342] sde: sde1
[ 4439.667442] sd 7:0:0:0: [sde] Attached SCSI removable disk
[ 4439.860368] FAT-fs (sde1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 4441.095233] FAT-fs (sdd1): Directory bread(block 28256) failed
[ 4441.095237] FAT-fs (sdd1): Directory bread(block 28257) failed
[ 4441.095238] FAT-fs (sdd1): Directory bread(block 28258) failed
[ 4441.095240] FAT-fs (sdd1): Directory bread(block 28259) failed
[ 4441.095241] FAT-fs (sdd1): Directory bread(block 28260) failed
[ 4441.095242] FAT-fs (sdd1): Directory bread(block 28261) failed
[ 4441.095244] FAT-fs (sdd1): Directory bread(block 28262) failed
[ 4441.095245] FAT-fs (sdd1): Directory bread(block 28263) failed
[ 4441.095246] FAT-fs (sdd1): Directory bread(block 28264) failed
[ 4441.095247] FAT-fs (sdd1): Directory bread(block 28265) failed
[ 4442.257558] ath10k_pci 0000:01:00.0: could not suspend target (-11)
[ 4447.592688] ath10k_pci 0000:01:00.0: failed to set tx-chainmask: -11, req 0x3
[-- Attachment #3: Type: text/plain, Size: 146 bytes --]
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
next reply other threads:[~2016-07-19 7:10 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-07-19 7:09 Stanislaw Gruszka [this message]
2016-07-19 7:18 ` ath10k fail to load firmware Michal Kazior
2016-07-19 7:27 ` Stanislaw Gruszka
2016-07-19 8:07 ` Perry_Yuan
2016-07-19 8:24 ` Perry_Yuan
2016-07-19 8:32 ` Michal Kazior
2016-07-19 9:02 ` Perry_Yuan
2016-07-19 9:17 ` Michal Kazior
2016-07-19 9:27 ` Stanislaw Gruszka
2016-07-19 9:41 ` Perry_Yuan
2016-07-20 3:14 ` Perry_Yuan
2016-07-20 6:58 ` Michal Kazior
2016-07-20 7:23 ` Perry_Yuan
[not found] ` <A3D794F1192BBF449DF2EC3D7EE263F44A5402F40A@SHAX7MCDC101.APAC.DELL.COM>
2016-07-25 10:25 ` Michal Kazior
2016-08-02 12:19 ` Valo, Kalle
2016-07-29 7:45 ` Perry_Yuan
2016-07-29 9:07 ` Perry_Yuan
2016-08-02 12:10 ` Valo, Kalle
2016-08-03 7:00 ` Michal Kazior
2016-08-22 8:40 ` Stanislaw Gruszka
2016-08-22 10:29 ` Valo, Kalle
2016-08-22 11:02 ` Stanislaw Gruszka
2016-08-22 14:05 ` Valo, Kalle
2016-08-23 18:55 ` Valo, Kalle
2016-08-24 6:33 ` Stanislaw Gruszka
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20160719070932.GA2751@redhat.com \
--to=sgruszka@redhat.com \
--cc=ath10k@lists.infradead.org \
--cc=kvalo@qca.qualcomm.com \
--cc=michal.kazior@tieto.com \
--cc=perry_yuan@dell.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.