All of lore.kernel.org
 help / color / mirror / Atom feed
From: shawnguo@kernel.org (Shawn Guo)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 0/7] ARM: dts: support I2SE Duckbill device
Date: Mon, 24 Oct 2016 21:12:09 +0800	[thread overview]
Message-ID: <20161024131209.GK30578@tiger> (raw)
In-Reply-To: <1477164150-13553-1-git-send-email-mhei@heimpold.de>

On Sat, Oct 22, 2016 at 09:22:23PM +0200, Michael Heimpold wrote:
> This series updates/adds Device Tree support for I2SE's Duckbill
> device family.
> 
> The Duckbill devices are small, pen-drive sized boards based on
> NXP's i.MX28 SoC. While the initial variants (Duckbill series) were
> equipped with a micro SD card slot only, the latest generation
> (Duckbill 2 series) have an additional internal eMMC onboard.
> 
> Both device generations consists of four "family members":
> 
> - Duckbill/Duckbill 2: generic board, intented to be used as
>   baseboard for custom designs and/or as development board
> 
> - Duckbill EnOcean/Duckbill 2 EnOcean: come with an EnOcean
>   daugther board equipped with the popular TCM310 module
> 
> - Duckbill 485/Duckbill 2 485: as the name implies, these
>   devices are intended to be used as Ethernet - RS485 converters
> 
> - Duckbill SPI/Duckbill 2 SPI: not sold separately, but used
>   in I2SE's development kits for Green PHY HomePlug Powerline
>   communication

So we basically need to maintain 8 dts/dtb files for imx28-duckbill
board.  This is not pleasant.  Can you please investigate if Device Tree
overlay is going to help here?

Shawn

[1] http://free-electrons.com/blog/dt-overlay-uboot-libfdt/

> Since all devices are very similar and only differ in few
> aspects, the following patch series introduces first common
> device tree snippets which are then included by the real
> devices. For better understanding, I tried to illustrate the
> hierarchy:
> 
> +--------------------+                      +----------------------+
> | imx28-duckbill.dts |                      | imx28-duckbill-2.dts |
> +--------------------+                      +----------------------+
>   ^                                           ^
>   |  +----------------------------+           |  +------------------------------+
>   |  | imx28-duckbill-enocean.dts |           |  | imx28-duckbill-2-enocean.dts |
>   |  +----------------------------+           |  +------------------------------+
>   |    ^                                      |    ^
>   |    |  +------------------------+          |    |  +--------------------------+
>   |    |  | imx28-duckbill-485.dts |          |    |  | imx28-duckbill-2-485.dts |
>   |    |  +------------------------+          |    |  +--------------------------+
>   |    |    ^                                 |    |    ^
>   |    |    |  +------------------------+     |    |    |  +--------------------------+
>   |    |    |  | imx28-duckbill-spi.dts |     |    |    |  | imx28-duckbill-2-spi.dts |
>   |    |    |  +------------------------+     |    |    |  +--------------------------+
>   |    |    |    ^                            |    |    |    ^
>   |    |    |    |                            |    |    |    |
>   |    |    |    |                            |    |    |    |
> +---------------------------------------+   +-----------------------------------------+
> |      imx28-duckbill-common.dtsi       |   |       imx28-duckbill-2-common.dtsi      |
> +---------------------------------------+   +-----------------------------------------+
>                               ^                      ^
>                               |                      |
>                            +----------------------------+
>                            |  imx28-duckbill-base.dtsi  |
>                            +----------------------------+
>                                           ^
>                                           |
>                                     +------------+
>                                     | imx28.dtsi |
>                                     +------------+
> 
> Michael Heimpold (7):
>   ARM: dts: imx28: add alternative pinmuxing for mmc2
>   ARM: dts: imx28: rename mmc2_sck_cfg to prepare for an alternative
>     muxing setup
>   ARM: dts: imx28: add alternative muxing for mmc2_sck_cfg
>   ARM: dts: add I2SE Duckbill common definitions
>   ARM: dts: duckbill: simplify DT and use common definitions
>   ARM: dts: add support for remaining members of Duckbill series
>   ARM: dts: add support for Duckbill 2 series devices
> 
>  arch/arm/boot/dts/Makefile                     |   7 ++
>  arch/arm/boot/dts/imx28-duckbill-2-485.dts     |  70 ++++++++++++++++
>  arch/arm/boot/dts/imx28-duckbill-2-common.dtsi | 110 +++++++++++++++++++++++++
>  arch/arm/boot/dts/imx28-duckbill-2-enocean.dts | 100 ++++++++++++++++++++++
>  arch/arm/boot/dts/imx28-duckbill-2-spi.dts     |  63 ++++++++++++++
>  arch/arm/boot/dts/imx28-duckbill-2.dts         |  46 +++++++++++
>  arch/arm/boot/dts/imx28-duckbill-485.dts       |  60 ++++++++++++++
>  arch/arm/boot/dts/imx28-duckbill-base.dtsi     |  88 ++++++++++++++++++++
>  arch/arm/boot/dts/imx28-duckbill-common.dtsi   |  80 ++++++++++++++++++
>  arch/arm/boot/dts/imx28-duckbill-enocean.dts   |  90 ++++++++++++++++++++
>  arch/arm/boot/dts/imx28-duckbill-spi.dts       |  64 ++++++++++++++
>  arch/arm/boot/dts/imx28-duckbill.dts           |  99 +++-------------------
>  arch/arm/boot/dts/imx28-m28cu3.dts             |   2 +-
>  arch/arm/boot/dts/imx28.dtsi                   |  28 ++++++-
>  14 files changed, 817 insertions(+), 90 deletions(-)
>  create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-485.dts
>  create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-common.dtsi
>  create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
>  create mode 100644 arch/arm/boot/dts/imx28-duckbill-2-spi.dts
>  create mode 100644 arch/arm/boot/dts/imx28-duckbill-2.dts
>  create mode 100644 arch/arm/boot/dts/imx28-duckbill-485.dts
>  create mode 100644 arch/arm/boot/dts/imx28-duckbill-base.dtsi
>  create mode 100644 arch/arm/boot/dts/imx28-duckbill-common.dtsi
>  create mode 100644 arch/arm/boot/dts/imx28-duckbill-enocean.dts
>  create mode 100644 arch/arm/boot/dts/imx28-duckbill-spi.dts
> 
> -- 
> 2.7.4
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2016-10-24 13:12 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-10-22 19:22 [PATCH 0/7] ARM: dts: support I2SE Duckbill device Michael Heimpold
2016-10-22 19:22 ` [PATCH 1/7] ARM: dts: imx28: add alternative pinmuxing for mmc2 Michael Heimpold
2016-10-22 19:22 ` [PATCH 2/7] ARM: dts: imx28: rename mmc2_sck_cfg to prepare for an alternative muxing setup Michael Heimpold
2016-10-22 19:22 ` [PATCH 3/7] ARM: dts: imx28: add alternative muxing for mmc2_sck_cfg Michael Heimpold
2016-10-22 19:22 ` [PATCH 4/7] ARM: dts: add I2SE Duckbill common definitions Michael Heimpold
2016-10-26 13:53   ` Shawn Guo
2016-10-22 19:22 ` [PATCH 5/7] ARM: dts: duckbill: simplify DT and use " Michael Heimpold
2016-10-22 19:22 ` [PATCH 6/7] ARM: dts: add support for remaining members of Duckbill series Michael Heimpold
2016-10-22 19:22 ` [PATCH 7/7] ARM: dts: add support for Duckbill 2 series devices Michael Heimpold
2016-10-24 13:12 ` Shawn Guo [this message]
2016-10-24 19:45   ` [PATCH 0/7] ARM: dts: support I2SE Duckbill device Michael Heimpold
2016-10-26 13:55     ` Shawn Guo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20161024131209.GK30578@tiger \
    --to=shawnguo@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.