[U-Boot] [PATCH v2 2/3] spl: dfu: move DFU Kconfig to SPL Kconfig

[Stefan Agner <stefan@agner.ch>]

From: Stefan Agner <stefan.agner@toradex.com>

The DFU Kconfig menu entries should be part of the SPL
Kconfig file. Also avoid using the top level Makefile by
moving the config dependent build artifacts to the driver/
and driver/usb/gadget/ Makfiles.

With that, DFU can be built again in SPL if
CONFIG_SPL_DFU_SUPPORT is enabled.

Fixes: 6ad6102246d8 ("usb:gadget: Disallow DFU in SPL for now")

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>

---
Tom, I checked size for am335x_evm_usbspl_defconfig, it stays
fine with this patch.

Changes in v2:
- Leave DWC3 config in top level SPL Makefile (as U-Boot does)

 Kconfig                      | 27 ---------------------------
 common/spl/Kconfig           | 26 ++++++++++++++++++++++++++
 drivers/Makefile             |  3 +++
 drivers/usb/gadget/Makefile  |  8 ++++++--
 include/configs/dra7xx_evm.h |  1 -
 scripts/Makefile.spl         |  3 ---
 6 files changed, 35 insertions(+), 33 deletions(-)

diff --git a/Kconfig b/Kconfig
index 1263d0b..a759e4d 100644
--- a/Kconfig
+++ b/Kconfig
@@ -291,33 +291,6 @@ config FIT_IMAGE_POST_PROCESS
 	  injected into the FIT creation (i.e. the blobs would have been pre-
 	  processed before being added to the FIT image).
 
-config SPL_DFU_SUPPORT
-	bool "Enable SPL with DFU to load binaries to memory device"
-	depends on USB
-	help
-	  Currently the SPL does not have capability to load the
-	  binaries or boot images to boot devices like ram,eMMC,SPI,etc.
-	  This feature enables the DFU (Device Firmware Upgarde) in SPL with
-	  RAM memory device support. The ROM code will load and execute
-	  the SPL built with dfu. The user can load binaries (u-boot/kernel) to
-	  selected device partition from host-pc using dfu-utils.
-		This feature will be useful to flash the binaries to factory
-	  or bare-metal boards using USB interface.
-
-choice
-	bool "DFU device selection"
-	depends on SPL_DFU_SUPPORT
-
-config SPL_DFU_RAM
-	bool "RAM device"
-	depends on SPL_DFU_SUPPORT
-	help
-	 select RAM/DDR memory device for loading binary images
-	 (u-boot/kernel) to the selected device partition using
-	 DFU and execute the u-boot/kernel from RAM.
-
-endchoice
-
 config SYS_CLK_FREQ
 	depends on ARC || ARCH_SUNXI
 	int "CPU clock frequency"
diff --git a/common/spl/Kconfig b/common/spl/Kconfig
index bb99f1f..54bcba3 100644
--- a/common/spl/Kconfig
+++ b/common/spl/Kconfig
@@ -497,6 +497,32 @@ config SPL_USB_SUPPORT
 	  config options. This enables loading from USB using a configured
 	  device.
 
+config SPL_DFU_SUPPORT
+	bool "Support DFU (Device Firmware Upgarde)"
+	depends on SPL
+	select SPL_HASH_SUPPORT
+	help
+	  This feature enables the DFU (Device Firmware Upgarde) in SPL with
+	  RAM memory device support. The ROM code will load and execute
+	  the SPL built with dfu. The user can load binaries (u-boot/kernel) to
+	  selected device partition from host-pc using dfu-utils.
+	  This feature is useful to flash the binaries to factory or bare-metal
+	  boards using USB interface.
+
+choice
+	bool "DFU device selection"
+	depends on SPL_DFU_SUPPORT
+
+config SPL_DFU_RAM
+	bool "RAM device"
+	depends on SPL_DFU_SUPPORT
+	help
+	 select RAM/DDR memory device for loading binary images
+	 (u-boot/kernel) to the selected device partition using
+	 DFU and execute the u-boot/kernel from RAM.
+
+endchoice
+
 config SPL_WATCHDOG_SUPPORT
 	bool "Support watchdog drivers"
 	depends on SPL
diff --git a/drivers/Makefile b/drivers/Makefile
index 761d0b3..40aba58 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -34,6 +34,9 @@ obj-$(CONFIG_SPL_ETH_SUPPORT) += net/phy/
 obj-$(CONFIG_SPL_USBETH_SUPPORT) += net/phy/
 obj-$(CONFIG_SPL_MUSB_NEW_SUPPORT) += usb/musb-new/
 obj-$(CONFIG_SPL_USBETH_SUPPORT) += usb/gadget/
+obj-$(CONFIG_SPL_DFU_SUPPORT) += usb/gadget/
+obj-$(CONFIG_SPL_DFU_SUPPORT) += usb/gadget/udc/
+obj-$(CONFIG_SPL_DFU_SUPPORT) += dfu/
 obj-$(CONFIG_SPL_WATCHDOG_SUPPORT) += watchdog/
 obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += usb/host/
 obj-$(CONFIG_OMAP_USB_PHY) += usb/phy/
diff --git a/drivers/usb/gadget/Makefile b/drivers/usb/gadget/Makefile
index acc9964..5b18e8c 100644
--- a/drivers/usb/gadget/Makefile
+++ b/drivers/usb/gadget/Makefile
@@ -8,6 +8,10 @@
 obj-$(CONFIG_USB_GADGET) += epautoconf.o config.o usbstring.o
 obj-$(CONFIG_USB_ETHER) += epautoconf.o config.o usbstring.o
 
+ifdef CONFIG_SPL_BUILD
+obj-$(CONFIG_SPL_DFU_SUPPORT) += f_dfu.o
+endif
+
 # new USB gadget layer dependencies
 ifdef CONFIG_USB_GADGET
 obj-$(CONFIG_USB_GADGET_AT91) += at91_udc.o
@@ -18,13 +22,13 @@ obj-$(CONFIG_USB_GADGET_DWC2_OTG_PHY) += dwc2_udc_otg_phy.o
 obj-$(CONFIG_USB_GADGET_FOTG210) += fotg210.o
 obj-$(CONFIG_CI_UDC)	+= ci_udc.o
 obj-$(CONFIG_USB_GADGET_DOWNLOAD) += g_dnl.o
-obj-$(CONFIG_USB_FUNCTION_THOR) += f_thor.o
 ifndef CONFIG_SPL_BUILD
+obj-$(CONFIG_USB_FUNCTION_THOR) += f_thor.o
 obj-$(CONFIG_USB_FUNCTION_DFU) += f_dfu.o
-endif
 obj-$(CONFIG_USB_FUNCTION_MASS_STORAGE) += f_mass_storage.o
 obj-$(CONFIG_USB_FUNCTION_FASTBOOT) += f_fastboot.o
 endif
+endif
 ifdef CONFIG_USB_ETHER
 obj-y += ether.o
 obj-$(CONFIG_USB_ETH_RNDIS) += rndis.o
diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h
index 798002d..e295a84 100644
--- a/include/configs/dra7xx_evm.h
+++ b/include/configs/dra7xx_evm.h
@@ -133,7 +133,6 @@
 #undef CONFIG_CMD_BOOTD
 #ifdef CONFIG_SPL_DFU_SUPPORT
 #define CONFIG_SPL_LOAD_FIT_ADDRESS 0x80200000
-#define CONFIG_SPL_HASH_SUPPORT
 #define DFU_ALT_INFO_RAM \
 	"dfu_alt_info_ram=" \
 	"kernel ram 0x80200000 0x4000000;" \
diff --git a/scripts/Makefile.spl b/scripts/Makefile.spl
index e0b0117..1e3b60a 100644
--- a/scripts/Makefile.spl
+++ b/scripts/Makefile.spl
@@ -66,9 +66,6 @@ endif
 
 libs-$(CONFIG_SPL_LIBDISK_SUPPORT) += disk/
 libs-y += drivers/
-libs-$(CONFIG_SPL_DFU_SUPPORT) += drivers/dfu/
-libs-$(CONFIG_SPL_DFU_SUPPORT) += drivers/usb/gadget/
-libs-$(CONFIG_SPL_DFU_SUPPORT) += drivers/usb/gadget/udc/
 libs-$(CONFIG_SPL_DFU_SUPPORT) += drivers/usb/dwc3/
 libs-y += dts/
 libs-y += fs/
-- 
2.10.2