Re: [PATCH 05/10] rt2800: make ba_size depend on ampdu_factor

[Stanislaw Gruszka <sgruszka@redhat.com>]

On Sat, Nov 05, 2016 at 01:56:58PM +0100, Mathias Kresin wrote:
> 02.11.2016 15:11, Stanislaw Gruszka:
> >
> >-		sta_priv = sta_to_rt2x00_sta(sta);
> >+		txdesc->u.ht.mpdu_density = sta->ht_cap.ampdu_density;
> > 		txdesc->u.ht.wcid = sta_priv->wcid;
> >+
> >+		if (!(tx_info->flags & IEEE80211_TX_CTL_RATE_CTRL_PROBE)) {
> >+			ba_size = IEEE80211_MIN_AMPDU_BUF;
> >+			ba_size <<= sta->ht_cap.ampdu_factor;
> >+			ba_size = min_t(int, 63, ba_size - 1);
> >+		}
> > 	}
> >
> > 	/*
> >@@ -345,7 +350,7 @@ static void rt2x00queue_create_tx_descriptor_ht(struct rt2x00_dev *rt2x00dev,
> > 		return;
> > 	}
> >
> >-	txdesc->u.ht.ba_size = 7;	/* FIXME: What value is needed? */
> >+	txdesc->u.ht.ba_size = ba_size;
> >
> > 	/*
> > 	 * Only one STBC stream is supported for now.
> >
> 
> Having this patch applied, the throughput on a vgv7510kw22 (RT3062F)
> in AP mode using LEDE head is decreased by somewhat around 10
> Mbits/sec. I'm using iperf3 for throughput tests and having this
> patch reverted the throughout is back to 80 Mbits/sec.
> 
> When bringing down the wifi interface the following messages are
> logged with the patch applied:
> 
> [  281.738373] ieee80211 phy0: rt2x00queue_flush_queue: Warning -
> Queue 2 failed to flush
> [  281.906380] ieee80211 phy0: rt2x00queue_flush_queue: Warning -
> Queue 2 failed to flush

Could you check below patch and see if it helps? If it does not,
could you printk sta->ht_cap.ampdu_density and ba_size values
and provide them here.

Thanks
Stanislaw 

diff --git a/drivers/net/wireless/ralink/rt2x00/rt2800lib.c b/drivers/net/wireless/ralink/rt2x00/rt2800lib.c
index 2515702..72c7948 100644
--- a/drivers/net/wireless/ralink/rt2x00/rt2800lib.c
+++ b/drivers/net/wireless/ralink/rt2x00/rt2800lib.c
@@ -4707,7 +4707,7 @@ static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
 	    rt2x00_rt_rev_lt(rt2x00dev, RT3070, REV_RT3070E))
 		rt2x00_set_field32(&reg, MAX_LEN_CFG_MAX_PSDU, 2);
 	else
-		rt2x00_set_field32(&reg, MAX_LEN_CFG_MAX_PSDU, 1);
+		rt2x00_set_field32(&reg, MAX_LEN_CFG_MAX_PSDU, 3;
 	rt2x00_set_field32(&reg, MAX_LEN_CFG_MIN_PSDU, 0);
 	rt2x00_set_field32(&reg, MAX_LEN_CFG_MIN_MPDU, 0);
 	rt2800_register_write(rt2x00dev, MAX_LEN_CFG, reg);