[PATCH v2 1/3] ARM: dts: udoo_neo: Add UDOO Neo USB OTG1 and OTG2 support

[shawnguo@kernel.org (Shawn Guo)]

On Thu, Jan 19, 2017 at 02:30:03PM -0200, Breno Lima wrote:
> Add support for micro USB (OTG1) and USB Host (OTG2) for UDOO Neo board.
> 
> Tested on a UDOO Neo Full board by mounting a mass storage device
> on both ports.
> 
> Signed-off-by: Breno Lima <breno.lima@nxp.com>
> ---
> Changes since v1:
> - imx6-usb-charger-detection property removed.
> 
>  arch/arm/boot/dts/imx6sx-udoo-neo.dtsi | 59 ++++++++++++++++++++++++++++++++++
>  1 file changed, 59 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi b/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
> index 2b65d26..e9d0596 100644
> --- a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
> +++ b/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
> @@ -75,6 +75,28 @@
>  		regulator-max-microvolt = <3300000>;
>  		regulator-boot-on;
>  	};
> +
> +	reg_usb_otg1_vbus: usb-otg1-vbus {

Please name fixed regulators like:

	reg_xxx: regulator-xxx {
		...
	};

Shawn

> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_otg1_reg>;
> +		regulator-name = "usb_otg1_vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	reg_usb_otg2_vbus: usb-otg2-vbus {
> +		compatible = "regulator-fixed";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_otg2_reg>;
> +		regulator-name = "usb_otg2_vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gpio4 12 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
>  };
>  
>  &cpu0 {
> @@ -241,6 +263,28 @@
>  			<MX6SX_PAD_CSI_DATA07__UART6_CTS_B	0x1b0b1>;
>  	};
>  
> +	pinctrl_otg1_reg: otg1grp {
> +		fsl,pins =
> +			<MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9        0x10b0>;
> +	};
> +
> +
> +	pinctrl_otg2_reg: otg2grp {
> +		fsl,pins =
> +			<MX6SX_PAD_NAND_RE_B__GPIO4_IO_12        0x10b0>;
> +	};
> +
> +	pinctrl_usb_otg1: usbotg1grp {
> +		fsl,pins =
> +			<MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID    0x17059>,
> +			<MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC       0x10b0>;
> +	};
> +
> +	pinctrl_usb_otg2: usbot2ggrp {
> +		fsl,pins =
> +			<MX6SX_PAD_QSPI1A_DATA0__USB_OTG2_OC     0x10b0>;
> +	};
> +
>  	pinctrl_usdhc2: usdhc2grp {
>  		fsl,pins =
>  			<MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x17059>,
> @@ -280,6 +324,21 @@
>  	status = "disabled";
>  };
>  
> +&usbotg1 { /* J2 micro USB port */
> +	vbus-supply = <&reg_usb_otg1_vbus>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usb_otg1>;
> +	status = "okay";
> +};
> +
> +&usbotg2 { /* J3 host USB port */
> +	vbus-supply = <&reg_usb_otg2_vbus>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usb_otg2>;
> +	dr_mode = "host";
> +	status = "okay";
> +};
> +
>  &usdhc2 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_usdhc2>;
> -- 
> 2.7.4
>