From: Andrew Lunn <andrew@lunn.ch>
To: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: shuah@kernel.org, davem@davemloft.net,
linux-kselftest@vger.kernel.org, linux-kernel@vger.kernel.org,
netdev@vger.kernel.org
Subject: Re: [PATCH v2] selftests: add a generic testsuite for ethernet device
Date: Tue, 4 Apr 2017 16:24:54 +0200 [thread overview]
Message-ID: <20170404142454.GC1736@lunn.ch> (raw)
In-Reply-To: <20170404133247.28725-1-clabbe.montjoie@gmail.com>
On Tue, Apr 04, 2017 at 03:32:47PM +0200, Corentin Labbe wrote:
> This patch add a generic testsuite for testing ethernet network device driver.
# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAUL0
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFA2
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFA2
link/ether a2:e2:da:92:7e:8c brd ff:ff:ff:ff:ff:ff
4: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default0
link/sit 0.0.0.0 brd 0.0.0.0
5: lan4@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state 0
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
6: lan3@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT0
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
7: lan2@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state 0
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
8: lan1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP0
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
9: internet@eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue st0
link/ether 94:10:3e:80:bc:f3 brd ff:ff:ff:ff:ff:ff
# /home/andrew/netdevice.sh
[ 151.417351] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
PASS: eth0: set interface up
PASS: eth0: set MAC address
SKIP: eth0: set IP address
PASS: eth0: ethtool list features
Cannot get register dump: Operation not supported
SKIP: eth0: ethtool dump not supported
PASS: eth0: ethtool stats
PASS: eth0: stop interface
SKIP: eth1: interface already up
PASS: eth1: ethtool list features
Cannot get register dump: Operation not supported
SKIP: eth1: ethtool dump not supported
PASS: eth1: ethtool stats
SKIP: eth1: interface kept up
PASS: eth0: set interface up
PASS: lan4: set MAC address
inet 192.168.13.2/24 brd 192.168.13.255 scope global lan4
SKIP: lan4: already have an IP
PASS: lan4: ethtool list features
PASS: lan4: ethtool dump
PASS: lan4: ethtool stats
PASS: eth0: stop interface
PASS: eth0: set interface up
PASS: lan3: set MAC address
SKIP: lan3: set IP address
PASS: lan3: ethtool list features
PASS: lan3: ethtool dump
PASS: lan3: ethtool stats
PASS: eth0: stop interface
PASS: eth0: set interface up
PASS: lan2: set MAC address
SKIP: lan2: set IP address
PASS: lan2: ethtool list features
PASS: lan2: ethtool dump
PASS: lan2: ethtool stats
PASS: eth0: stop interface
PASS: eth0: set interface up
PASS: lan1: set MAC address
inet 10.0.0.12/24 brd 10.0.0.255 scope global lan1
SKIP: lan1: already have an IP
PASS: lan1: ethtool list features
PASS: lan1: ethtool dump
PASS: lan1: ethtool stats
PASS: eth0: stop interface
PASS: eth0: set interface up
PASS: internet: set MAC address
inet 192.168.10.2/24 brd 192.168.10.255 scope global internet
SKIP: internet: already have an IP
PASS: internet: ethtool list features
PASS: internet: ethtool dump
PASS: internet: ethtool stats
PASS: eth0: stop interface
Cool
Tested-by: Andrew Lunn <andrew@lunn.ch>
Andrew
next prev parent reply other threads:[~2017-04-04 14:25 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-04-04 13:32 [PATCH v2] selftests: add a generic testsuite for ethernet device Corentin Labbe
2017-04-04 14:24 ` Andrew Lunn [this message]
2017-04-04 14:43 ` Niklas Cassel
2017-04-04 14:50 ` Corentin Labbe
2017-04-04 15:00 ` Andrew Lunn
2017-04-05 15:30 ` David Miller
2017-06-29 8:26 ` Fathi Boudra
2017-07-01 6:42 ` Corentin Labbe
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170404142454.GC1736@lunn.ch \
--to=andrew@lunn.ch \
--cc=clabbe.montjoie@gmail.com \
--cc=davem@davemloft.net \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-kselftest@vger.kernel.org \
--cc=netdev@vger.kernel.org \
--cc=shuah@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.