From mboxrd@z Thu Jan 1 00:00:00 1970 From: Kishon Vijay Abraham I Subject: [PATCH 03/41] mmc: host: omap_hsmmc: Program HCTL based on signal_voltage set by mmc core Date: Fri, 19 May 2017 13:45:03 +0530 Message-ID: <20170519081541.26753-4-kishon@ti.com> References: <20170519081541.26753-1-kishon@ti.com> Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Return-path: In-Reply-To: <20170519081541.26753-1-kishon@ti.com> List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Sender: "linux-arm-kernel" Errors-To: linux-arm-kernel-bounces+linux-arm-kernel=m.gmane.org@lists.infradead.org To: Ulf Hansson , Rob Herring , Tony Lindgren Cc: Mark Rutland , devicetree@vger.kernel.org, linux-doc@vger.kernel.org, nsekhar@ti.com, Jonathan Corbet , linux-mmc@vger.kernel.org, linux-kernel@vger.kernel.org, Russell King , kishon@ti.com, linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org List-Id: linux-mmc@vger.kernel.org HCTL is now set based on ios.signal_voltage set by mmc core and not hardcoded to 3V0 if OMAP_HSMMC_SUPPORTS_DUAL_VOLT is set. If OMAP_HSMMC_SUPPORTS_DUAL_VOLT is set, it means HCTL can be set to either 3V0 or 1V8. And it should be set to 3V0 or 1V8 depending on ios.signal_voltage. Also it is now set on power mode status being changed to MMC_POWER_ON. Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Sekhar Nori --- drivers/mmc/host/omap_hsmmc.c | 16 +++++++--------- 1 file changed, 7 insertions(+), 9 deletions(-) diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c index 42954efe12f7..893d1624a5a3 100644 --- a/drivers/mmc/host/omap_hsmmc.c +++ b/drivers/mmc/host/omap_hsmmc.c @@ -229,6 +229,7 @@ struct omap_mmc_of_data { }; static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host); +static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host, int iov); static int omap_hsmmc_card_detect(struct device *dev) { @@ -1664,6 +1665,7 @@ static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) omap_hsmmc_set_power(host, 1, ios->vdd); break; case MMC_POWER_ON: + omap_hsmmc_conf_bus_power(host, ios->signal_voltage); do_send_init_stream = 1; break; } @@ -1824,17 +1826,12 @@ static void omap_hsmmc_set_capabilities(struct omap_hsmmc_host *host) OMAP_HSMMC_WRITE(host->base, CAPA, val); } -static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host) +static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host, int iov) { u32 hctl, value; - /* Only MMC1 supports 3.0V */ - if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) - hctl = SDVS30; - else - hctl = SDVS18; - value = OMAP_HSMMC_READ(host->base, HCTL) & ~SDVS_MASK; + hctl = (iov == MMC_SIGNAL_VOLTAGE_180) ? SDVS18 : SDVS30; OMAP_HSMMC_WRITE(host->base, HCTL, value | hctl); /* Set SD bus power bit */ @@ -2144,7 +2141,6 @@ static int omap_hsmmc_probe(struct platform_device *pdev) mmc->pm_caps |= mmc_pdata(host)->pm_caps; omap_hsmmc_set_capabilities(host); - omap_hsmmc_conf_bus_power(host); host->rx_chan = dma_request_chan(&pdev->dev, "rx"); if (IS_ERR(host->rx_chan)) { @@ -2281,6 +2277,7 @@ static int omap_hsmmc_suspend(struct device *dev) static int omap_hsmmc_resume(struct device *dev) { struct omap_hsmmc_host *host = dev_get_drvdata(dev); + struct mmc_ios *ios; if (!host) return 0; @@ -2290,8 +2287,9 @@ static int omap_hsmmc_resume(struct device *dev) if (host->dbclk) clk_prepare_enable(host->dbclk); + ios = &host->mmc->ios; if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER)) - omap_hsmmc_conf_bus_power(host); + omap_hsmmc_conf_bus_power(host, ios->signal_voltage); omap_hsmmc_protect_card(host); pm_runtime_mark_last_busy(host->dev); -- 2.11.0 From mboxrd@z Thu Jan 1 00:00:00 1970 From: kishon@ti.com (Kishon Vijay Abraham I) Date: Fri, 19 May 2017 13:45:03 +0530 Subject: [PATCH 03/41] mmc: host: omap_hsmmc: Program HCTL based on signal_voltage set by mmc core In-Reply-To: <20170519081541.26753-1-kishon@ti.com> References: <20170519081541.26753-1-kishon@ti.com> Message-ID: <20170519081541.26753-4-kishon@ti.com> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org HCTL is now set based on ios.signal_voltage set by mmc core and not hardcoded to 3V0 if OMAP_HSMMC_SUPPORTS_DUAL_VOLT is set. If OMAP_HSMMC_SUPPORTS_DUAL_VOLT is set, it means HCTL can be set to either 3V0 or 1V8. And it should be set to 3V0 or 1V8 depending on ios.signal_voltage. Also it is now set on power mode status being changed to MMC_POWER_ON. Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Sekhar Nori --- drivers/mmc/host/omap_hsmmc.c | 16 +++++++--------- 1 file changed, 7 insertions(+), 9 deletions(-) diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c index 42954efe12f7..893d1624a5a3 100644 --- a/drivers/mmc/host/omap_hsmmc.c +++ b/drivers/mmc/host/omap_hsmmc.c @@ -229,6 +229,7 @@ struct omap_mmc_of_data { }; static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host); +static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host, int iov); static int omap_hsmmc_card_detect(struct device *dev) { @@ -1664,6 +1665,7 @@ static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) omap_hsmmc_set_power(host, 1, ios->vdd); break; case MMC_POWER_ON: + omap_hsmmc_conf_bus_power(host, ios->signal_voltage); do_send_init_stream = 1; break; } @@ -1824,17 +1826,12 @@ static void omap_hsmmc_set_capabilities(struct omap_hsmmc_host *host) OMAP_HSMMC_WRITE(host->base, CAPA, val); } -static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host) +static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host, int iov) { u32 hctl, value; - /* Only MMC1 supports 3.0V */ - if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) - hctl = SDVS30; - else - hctl = SDVS18; - value = OMAP_HSMMC_READ(host->base, HCTL) & ~SDVS_MASK; + hctl = (iov == MMC_SIGNAL_VOLTAGE_180) ? SDVS18 : SDVS30; OMAP_HSMMC_WRITE(host->base, HCTL, value | hctl); /* Set SD bus power bit */ @@ -2144,7 +2141,6 @@ static int omap_hsmmc_probe(struct platform_device *pdev) mmc->pm_caps |= mmc_pdata(host)->pm_caps; omap_hsmmc_set_capabilities(host); - omap_hsmmc_conf_bus_power(host); host->rx_chan = dma_request_chan(&pdev->dev, "rx"); if (IS_ERR(host->rx_chan)) { @@ -2281,6 +2277,7 @@ static int omap_hsmmc_suspend(struct device *dev) static int omap_hsmmc_resume(struct device *dev) { struct omap_hsmmc_host *host = dev_get_drvdata(dev); + struct mmc_ios *ios; if (!host) return 0; @@ -2290,8 +2287,9 @@ static int omap_hsmmc_resume(struct device *dev) if (host->dbclk) clk_prepare_enable(host->dbclk); + ios = &host->mmc->ios; if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER)) - omap_hsmmc_conf_bus_power(host); + omap_hsmmc_conf_bus_power(host, ios->signal_voltage); omap_hsmmc_protect_card(host); pm_runtime_mark_last_busy(host->dev); -- 2.11.0 From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1755892AbdESIa4 (ORCPT ); Fri, 19 May 2017 04:30:56 -0400 Received: from lelnx193.ext.ti.com ([198.47.27.77]:10278 "EHLO lelnx193.ext.ti.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752968AbdESIQz (ORCPT ); Fri, 19 May 2017 04:16:55 -0400 From: Kishon Vijay Abraham I To: Ulf Hansson , Rob Herring , Tony Lindgren CC: , , , , , , Jonathan Corbet , Mark Rutland , Russell King , , Subject: [PATCH 03/41] mmc: host: omap_hsmmc: Program HCTL based on signal_voltage set by mmc core Date: Fri, 19 May 2017 13:45:03 +0530 Message-ID: <20170519081541.26753-4-kishon@ti.com> X-Mailer: git-send-email 2.11.0 In-Reply-To: <20170519081541.26753-1-kishon@ti.com> References: <20170519081541.26753-1-kishon@ti.com> MIME-Version: 1.0 Content-Type: text/plain Sender: linux-kernel-owner@vger.kernel.org List-ID: X-Mailing-List: linux-kernel@vger.kernel.org HCTL is now set based on ios.signal_voltage set by mmc core and not hardcoded to 3V0 if OMAP_HSMMC_SUPPORTS_DUAL_VOLT is set. If OMAP_HSMMC_SUPPORTS_DUAL_VOLT is set, it means HCTL can be set to either 3V0 or 1V8. And it should be set to 3V0 or 1V8 depending on ios.signal_voltage. Also it is now set on power mode status being changed to MMC_POWER_ON. Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Sekhar Nori --- drivers/mmc/host/omap_hsmmc.c | 16 +++++++--------- 1 file changed, 7 insertions(+), 9 deletions(-) diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c index 42954efe12f7..893d1624a5a3 100644 --- a/drivers/mmc/host/omap_hsmmc.c +++ b/drivers/mmc/host/omap_hsmmc.c @@ -229,6 +229,7 @@ struct omap_mmc_of_data { }; static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host); +static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host, int iov); static int omap_hsmmc_card_detect(struct device *dev) { @@ -1664,6 +1665,7 @@ static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) omap_hsmmc_set_power(host, 1, ios->vdd); break; case MMC_POWER_ON: + omap_hsmmc_conf_bus_power(host, ios->signal_voltage); do_send_init_stream = 1; break; } @@ -1824,17 +1826,12 @@ static void omap_hsmmc_set_capabilities(struct omap_hsmmc_host *host) OMAP_HSMMC_WRITE(host->base, CAPA, val); } -static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host) +static void omap_hsmmc_conf_bus_power(struct omap_hsmmc_host *host, int iov) { u32 hctl, value; - /* Only MMC1 supports 3.0V */ - if (host->pdata->controller_flags & OMAP_HSMMC_SUPPORTS_DUAL_VOLT) - hctl = SDVS30; - else - hctl = SDVS18; - value = OMAP_HSMMC_READ(host->base, HCTL) & ~SDVS_MASK; + hctl = (iov == MMC_SIGNAL_VOLTAGE_180) ? SDVS18 : SDVS30; OMAP_HSMMC_WRITE(host->base, HCTL, value | hctl); /* Set SD bus power bit */ @@ -2144,7 +2141,6 @@ static int omap_hsmmc_probe(struct platform_device *pdev) mmc->pm_caps |= mmc_pdata(host)->pm_caps; omap_hsmmc_set_capabilities(host); - omap_hsmmc_conf_bus_power(host); host->rx_chan = dma_request_chan(&pdev->dev, "rx"); if (IS_ERR(host->rx_chan)) { @@ -2281,6 +2277,7 @@ static int omap_hsmmc_suspend(struct device *dev) static int omap_hsmmc_resume(struct device *dev) { struct omap_hsmmc_host *host = dev_get_drvdata(dev); + struct mmc_ios *ios; if (!host) return 0; @@ -2290,8 +2287,9 @@ static int omap_hsmmc_resume(struct device *dev) if (host->dbclk) clk_prepare_enable(host->dbclk); + ios = &host->mmc->ios; if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER)) - omap_hsmmc_conf_bus_power(host); + omap_hsmmc_conf_bus_power(host, ios->signal_voltage); omap_hsmmc_protect_card(host); pm_runtime_mark_last_busy(host->dev); -- 2.11.0