RE: regulatory.db file for ath10k

["KAVITA MATHUR" <kavitam@cdot.in>]

Thankyou so much for this information. 

I do not want to use regulatory.db. Can you please share your ath10k build
configuration? I may be missing something in configuration.

Thanks & Regards,
Kavita


On Wed, 13 Dec 2017 07:54:00 +0000, Manikanta Pubbisetty wrote
> Please CC linux wireless when posting queries on cfg/mac80211.
> 
> At least, I have not had any issues in interface bring up after the latest 
> regulatory.db change, I have tested it with vanilla ath.git and it worked even 
> without regulatory.db file. If you may want to refer, Johannes submitted a 
> patch[1] for converting db.txt to firmware file format.
> 
> [1] https://patchwork.kernel.org/patch/9992477/
> 
> mkp
> 
> >-----Original Message-----
> >From: ath10k [mailto:ath10k-bounces@lists.infradead.org] On Behalf Of
> >KAVITA MATHUR
> >Sent: Wednesday, December 13, 2017 12:02 PM
> >To: ath10k@lists.infradead.org
> >Subject: regulatory.db file for ath10k
> >
> >hi,
> >
> >wifi interface is not up with ath10k driver due to missing regulatory.db.I have
> >taken ath10k latest driver code from backports and ath10k git on 12 Dec.
> >
> >
> >
> >Loading modules backported from Linux version v3.18-239930-g135da6d
> >Backport generated by backports.git v4.14-rc2-1-35-g3d13478 ath10k_pci
> >0002:03:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
> >cfg80211: failed to load regulatory.db
> >ath10k_pci 0002:03:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043222ff
> >sub 0000:0000 ath10k_pci 0002:03:00.0: kconfig debug 0 debugfs 0 tracing 0 dfs
> >0 testmode 0 ath10k_pci 0002:03:00.0: firmware ver 10.2.4.70.66 api 5 features
> >no-p2p,raw-mode,mfp,allows-mesh-bcast crc32 c2dd2ad5 ath10k_pci
> >0002:03:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 ath10k_pci
> >0002:03:00.0: htt-ver 2.1 wmi-op 5 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto
> >1
> >
> >wifi
> >root@CDOT:/# IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready device
> >wlan0 entered promiscuous mode device wlan0 left promiscuous mode
> >br-lan: port 2(wlan0) entered disabled state
> >
> >How to generate regulatory.db file or is it available to use it directly? Please
> >help me to fix it.
> >
> >
> >
> >
> >
> >
> >
> >
> >Thanks & Regards,
> >कविता माथुर Kavita Mathur
> >वरिष्ठ अनुसंधान अभियंता  Senior Research Engineer
> >सी-डॉट                      C-DOT
> >इलैक्ट्रॉनिक्स सिटी फेज़ I         Electronics City Phase I
> >होसूर रोड, बेंगलूरु               Hosur Road, Bengaluru – 560100
> >फोन  Ph 080-28529896
> >Disclaimer:
> >----------
> >This email and any files transmitted with it
> >
> >
> >_______________________________________________
> >ath10k mailing list
> >ath10k@lists.infradead.org
> >http://lists.infradead.org/mailman/listinfo/ath10k


Thanks & Regards,
कविता माथुर Kavita Mathur 
वरिष्ठ अनुसंधान अभियंता  Senior Research Engineer 
सी-डॉट                      C-DOT
इलैक्ट्रॉनिक्स सिटी फेज़ I         Electronics City Phase I
होसूर रोड, बेंगलूरु               Hosur Road, Bengaluru – 560100
फोन  Ph 080-28529896
Disclaimer:
----------
This email and any files transmitted with it


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k