* [Qemu-devel] [PATCH v2 0/3] virtio_net: allow hypervisor to indicate linkspeed and duplex setting
@ 2017-12-22 21:54 ` Jason Baron
0 siblings, 0 replies; 26+ messages in thread
From: Jason Baron @ 2017-12-22 21:54 UTC (permalink / raw)
To: netdev, virtualization, qemu-devel; +Cc: mst, jasowang
We have found it useful to be able to set the linkspeed and duplex
settings from the host-side for virtio_net. This obviates the need
for guest changes and settings for these fields, and does not require
custom ethtool commands for virtio_net.
The ability to set linkspeed and duplex is useful in various cases
as described here:
16032be virtio_net: add ethtool support for set and get of settings
Using 'ethtool -s' continues to over-write the linkspeed/duplex
settings with this patch.
The 1/3 patch is against net-next, while the 2-3/3 patch are the associated
qemu changes that would go in after as update-linux-headers.sh should
be run first. So the qemu patches are a demonstration of how I intend this
to work.
Thanks,
-Jason
linux changes:
Jason Baron (1):
virtio_net: propagate linkspeed/duplex settings from the hypervisor
drivers/net/virtio_net.c | 17 ++++++++++++++++-
include/uapi/linux/virtio_net.h | 5 +++++
2 files changed, 21 insertions(+), 1 deletion(-)
qemu changes:
Jason Baron (2):
qemu: virtio-net: use 64-bit values for feature flags
qemu: add linkspeed and duplex settings to virtio-net
hw/net/virtio-net.c | 83 +++++++++++++++++++----------
include/hw/virtio/virtio-net.h | 5 +-
include/standard-headers/linux/virtio_net.h | 4 ++
3 files changed, 64 insertions(+), 28 deletions(-)
^ permalink raw reply [flat|nested] 26+ messages in thread* [PATCH 2/3] qemu: use 64-bit values for feature flags in virtio-net
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
@ 2017-12-22 21:53 ` Jason Baron
-1 siblings, 0 replies; 26+ messages in thread
From: Jason Baron @ 2017-12-22 21:53 UTC (permalink / raw)
To: netdev, virtualization, qemu-devel; +Cc: mst, jasowang
In prepartion for using some of the high order feature bits, make sure that
virtio-net uses 64-bit values everywhere.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
---
hw/net/virtio-net.c | 54 +++++++++++++++++++++---------------------
include/hw/virtio/virtio-net.h | 2 +-
2 files changed, 28 insertions(+), 28 deletions(-)
diff --git a/hw/net/virtio-net.c b/hw/net/virtio-net.c
index 38674b0..adc20df 100644
--- a/hw/net/virtio-net.c
+++ b/hw/net/virtio-net.c
@@ -48,18 +48,18 @@
(offsetof(container, field) + sizeof(((container *)0)->field))
typedef struct VirtIOFeature {
- uint32_t flags;
+ uint64_t flags;
size_t end;
} VirtIOFeature;
static VirtIOFeature feature_sizes[] = {
- {.flags = 1 << VIRTIO_NET_F_MAC,
+ {.flags = 1ULL << VIRTIO_NET_F_MAC,
.end = endof(struct virtio_net_config, mac)},
- {.flags = 1 << VIRTIO_NET_F_STATUS,
+ {.flags = 1ULL << VIRTIO_NET_F_STATUS,
.end = endof(struct virtio_net_config, status)},
- {.flags = 1 << VIRTIO_NET_F_MQ,
+ {.flags = 1ULL << VIRTIO_NET_F_MQ,
.end = endof(struct virtio_net_config, max_virtqueue_pairs)},
- {.flags = 1 << VIRTIO_NET_F_MTU,
+ {.flags = 1ULL << VIRTIO_NET_F_MTU,
.end = endof(struct virtio_net_config, mtu)},
{}
};
@@ -1938,7 +1938,7 @@ static void virtio_net_device_realize(DeviceState *dev, Error **errp)
int i;
if (n->net_conf.mtu) {
- n->host_features |= (0x1 << VIRTIO_NET_F_MTU);
+ n->host_features |= (1ULL << VIRTIO_NET_F_MTU);
}
virtio_net_set_config_size(n, n->host_features);
@@ -2109,45 +2109,45 @@ static const VMStateDescription vmstate_virtio_net = {
};
static Property virtio_net_properties[] = {
- DEFINE_PROP_BIT("csum", VirtIONet, host_features, VIRTIO_NET_F_CSUM, true),
- DEFINE_PROP_BIT("guest_csum", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("csum", VirtIONet, host_features, VIRTIO_NET_F_CSUM, true),
+ DEFINE_PROP_BIT64("guest_csum", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_CSUM, true),
- DEFINE_PROP_BIT("gso", VirtIONet, host_features, VIRTIO_NET_F_GSO, true),
- DEFINE_PROP_BIT("guest_tso4", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("gso", VirtIONet, host_features, VIRTIO_NET_F_GSO, true),
+ DEFINE_PROP_BIT64("guest_tso4", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_TSO4, true),
- DEFINE_PROP_BIT("guest_tso6", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_tso6", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_TSO6, true),
- DEFINE_PROP_BIT("guest_ecn", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_ecn", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_ECN, true),
- DEFINE_PROP_BIT("guest_ufo", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_ufo", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_UFO, true),
- DEFINE_PROP_BIT("guest_announce", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_announce", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_ANNOUNCE, true),
- DEFINE_PROP_BIT("host_tso4", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_tso4", VirtIONet, host_features,
VIRTIO_NET_F_HOST_TSO4, true),
- DEFINE_PROP_BIT("host_tso6", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_tso6", VirtIONet, host_features,
VIRTIO_NET_F_HOST_TSO6, true),
- DEFINE_PROP_BIT("host_ecn", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_ecn", VirtIONet, host_features,
VIRTIO_NET_F_HOST_ECN, true),
- DEFINE_PROP_BIT("host_ufo", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_ufo", VirtIONet, host_features,
VIRTIO_NET_F_HOST_UFO, true),
- DEFINE_PROP_BIT("mrg_rxbuf", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("mrg_rxbuf", VirtIONet, host_features,
VIRTIO_NET_F_MRG_RXBUF, true),
- DEFINE_PROP_BIT("status", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("status", VirtIONet, host_features,
VIRTIO_NET_F_STATUS, true),
- DEFINE_PROP_BIT("ctrl_vq", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_vq", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_VQ, true),
- DEFINE_PROP_BIT("ctrl_rx", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_rx", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_RX, true),
- DEFINE_PROP_BIT("ctrl_vlan", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_vlan", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_VLAN, true),
- DEFINE_PROP_BIT("ctrl_rx_extra", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_rx_extra", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_RX_EXTRA, true),
- DEFINE_PROP_BIT("ctrl_mac_addr", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_mac_addr", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_MAC_ADDR, true),
- DEFINE_PROP_BIT("ctrl_guest_offloads", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_guest_offloads", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, true),
- DEFINE_PROP_BIT("mq", VirtIONet, host_features, VIRTIO_NET_F_MQ, false),
+ DEFINE_PROP_BIT64("mq", VirtIONet, host_features, VIRTIO_NET_F_MQ, false),
DEFINE_NIC_PROPERTIES(VirtIONet, nic_conf),
DEFINE_PROP_UINT32("x-txtimer", VirtIONet, net_conf.txtimer,
TX_TIMER_INTERVAL),
diff --git a/include/hw/virtio/virtio-net.h b/include/hw/virtio/virtio-net.h
index b81b6a4..e7634c9 100644
--- a/include/hw/virtio/virtio-net.h
+++ b/include/hw/virtio/virtio-net.h
@@ -67,7 +67,7 @@ typedef struct VirtIONet {
uint32_t has_vnet_hdr;
size_t host_hdr_len;
size_t guest_hdr_len;
- uint32_t host_features;
+ uint64_t host_features;
uint8_t has_ufo;
uint32_t mergeable_rx_bufs;
uint8_t promisc;
--
2.6.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* [Qemu-devel] [PATCH 2/3] qemu: use 64-bit values for feature flags in virtio-net
@ 2017-12-22 21:53 ` Jason Baron
0 siblings, 0 replies; 26+ messages in thread
From: Jason Baron @ 2017-12-22 21:53 UTC (permalink / raw)
To: netdev, virtualization, qemu-devel; +Cc: mst, jasowang
In prepartion for using some of the high order feature bits, make sure that
virtio-net uses 64-bit values everywhere.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
---
hw/net/virtio-net.c | 54 +++++++++++++++++++++---------------------
include/hw/virtio/virtio-net.h | 2 +-
2 files changed, 28 insertions(+), 28 deletions(-)
diff --git a/hw/net/virtio-net.c b/hw/net/virtio-net.c
index 38674b0..adc20df 100644
--- a/hw/net/virtio-net.c
+++ b/hw/net/virtio-net.c
@@ -48,18 +48,18 @@
(offsetof(container, field) + sizeof(((container *)0)->field))
typedef struct VirtIOFeature {
- uint32_t flags;
+ uint64_t flags;
size_t end;
} VirtIOFeature;
static VirtIOFeature feature_sizes[] = {
- {.flags = 1 << VIRTIO_NET_F_MAC,
+ {.flags = 1ULL << VIRTIO_NET_F_MAC,
.end = endof(struct virtio_net_config, mac)},
- {.flags = 1 << VIRTIO_NET_F_STATUS,
+ {.flags = 1ULL << VIRTIO_NET_F_STATUS,
.end = endof(struct virtio_net_config, status)},
- {.flags = 1 << VIRTIO_NET_F_MQ,
+ {.flags = 1ULL << VIRTIO_NET_F_MQ,
.end = endof(struct virtio_net_config, max_virtqueue_pairs)},
- {.flags = 1 << VIRTIO_NET_F_MTU,
+ {.flags = 1ULL << VIRTIO_NET_F_MTU,
.end = endof(struct virtio_net_config, mtu)},
{}
};
@@ -1938,7 +1938,7 @@ static void virtio_net_device_realize(DeviceState *dev, Error **errp)
int i;
if (n->net_conf.mtu) {
- n->host_features |= (0x1 << VIRTIO_NET_F_MTU);
+ n->host_features |= (1ULL << VIRTIO_NET_F_MTU);
}
virtio_net_set_config_size(n, n->host_features);
@@ -2109,45 +2109,45 @@ static const VMStateDescription vmstate_virtio_net = {
};
static Property virtio_net_properties[] = {
- DEFINE_PROP_BIT("csum", VirtIONet, host_features, VIRTIO_NET_F_CSUM, true),
- DEFINE_PROP_BIT("guest_csum", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("csum", VirtIONet, host_features, VIRTIO_NET_F_CSUM, true),
+ DEFINE_PROP_BIT64("guest_csum", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_CSUM, true),
- DEFINE_PROP_BIT("gso", VirtIONet, host_features, VIRTIO_NET_F_GSO, true),
- DEFINE_PROP_BIT("guest_tso4", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("gso", VirtIONet, host_features, VIRTIO_NET_F_GSO, true),
+ DEFINE_PROP_BIT64("guest_tso4", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_TSO4, true),
- DEFINE_PROP_BIT("guest_tso6", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_tso6", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_TSO6, true),
- DEFINE_PROP_BIT("guest_ecn", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_ecn", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_ECN, true),
- DEFINE_PROP_BIT("guest_ufo", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_ufo", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_UFO, true),
- DEFINE_PROP_BIT("guest_announce", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_announce", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_ANNOUNCE, true),
- DEFINE_PROP_BIT("host_tso4", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_tso4", VirtIONet, host_features,
VIRTIO_NET_F_HOST_TSO4, true),
- DEFINE_PROP_BIT("host_tso6", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_tso6", VirtIONet, host_features,
VIRTIO_NET_F_HOST_TSO6, true),
- DEFINE_PROP_BIT("host_ecn", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_ecn", VirtIONet, host_features,
VIRTIO_NET_F_HOST_ECN, true),
- DEFINE_PROP_BIT("host_ufo", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_ufo", VirtIONet, host_features,
VIRTIO_NET_F_HOST_UFO, true),
- DEFINE_PROP_BIT("mrg_rxbuf", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("mrg_rxbuf", VirtIONet, host_features,
VIRTIO_NET_F_MRG_RXBUF, true),
- DEFINE_PROP_BIT("status", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("status", VirtIONet, host_features,
VIRTIO_NET_F_STATUS, true),
- DEFINE_PROP_BIT("ctrl_vq", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_vq", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_VQ, true),
- DEFINE_PROP_BIT("ctrl_rx", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_rx", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_RX, true),
- DEFINE_PROP_BIT("ctrl_vlan", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_vlan", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_VLAN, true),
- DEFINE_PROP_BIT("ctrl_rx_extra", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_rx_extra", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_RX_EXTRA, true),
- DEFINE_PROP_BIT("ctrl_mac_addr", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_mac_addr", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_MAC_ADDR, true),
- DEFINE_PROP_BIT("ctrl_guest_offloads", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_guest_offloads", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, true),
- DEFINE_PROP_BIT("mq", VirtIONet, host_features, VIRTIO_NET_F_MQ, false),
+ DEFINE_PROP_BIT64("mq", VirtIONet, host_features, VIRTIO_NET_F_MQ, false),
DEFINE_NIC_PROPERTIES(VirtIONet, nic_conf),
DEFINE_PROP_UINT32("x-txtimer", VirtIONet, net_conf.txtimer,
TX_TIMER_INTERVAL),
diff --git a/include/hw/virtio/virtio-net.h b/include/hw/virtio/virtio-net.h
index b81b6a4..e7634c9 100644
--- a/include/hw/virtio/virtio-net.h
+++ b/include/hw/virtio/virtio-net.h
@@ -67,7 +67,7 @@ typedef struct VirtIONet {
uint32_t has_vnet_hdr;
size_t host_hdr_len;
size_t guest_hdr_len;
- uint32_t host_features;
+ uint64_t host_features;
uint8_t has_ufo;
uint32_t mergeable_rx_bufs;
uint8_t promisc;
--
2.6.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* [PATCH v2 0/3] virtio_net: allow hypervisor to indicate linkspeed and duplex setting
2017-12-22 21:53 ` [Qemu-devel] " Jason Baron
(?)
@ 2017-12-22 21:54 ` Jason Baron via Virtualization
-1 siblings, 0 replies; 26+ messages in thread
From: Jason Baron via Virtualization @ 2017-12-22 21:54 UTC (permalink / raw)
To: netdev, virtualization, qemu-devel; +Cc: mst
We have found it useful to be able to set the linkspeed and duplex
settings from the host-side for virtio_net. This obviates the need
for guest changes and settings for these fields, and does not require
custom ethtool commands for virtio_net.
The ability to set linkspeed and duplex is useful in various cases
as described here:
16032be virtio_net: add ethtool support for set and get of settings
Using 'ethtool -s' continues to over-write the linkspeed/duplex
settings with this patch.
The 1/3 patch is against net-next, while the 2-3/3 patch are the associated
qemu changes that would go in after as update-linux-headers.sh should
be run first. So the qemu patches are a demonstration of how I intend this
to work.
Thanks,
-Jason
linux changes:
Jason Baron (1):
virtio_net: propagate linkspeed/duplex settings from the hypervisor
drivers/net/virtio_net.c | 17 ++++++++++++++++-
include/uapi/linux/virtio_net.h | 5 +++++
2 files changed, 21 insertions(+), 1 deletion(-)
qemu changes:
Jason Baron (2):
qemu: virtio-net: use 64-bit values for feature flags
qemu: add linkspeed and duplex settings to virtio-net
hw/net/virtio-net.c | 83 +++++++++++++++++++----------
include/hw/virtio/virtio-net.h | 5 +-
include/standard-headers/linux/virtio_net.h | 4 ++
3 files changed, 64 insertions(+), 28 deletions(-)
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 2/3] qemu: use 64-bit values for feature flags in virtio-net
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
(?)
(?)
@ 2017-12-22 21:53 ` Jason Baron via Virtualization
-1 siblings, 0 replies; 26+ messages in thread
From: Jason Baron via Virtualization @ 2017-12-22 21:53 UTC (permalink / raw)
To: netdev, virtualization, qemu-devel; +Cc: mst
In prepartion for using some of the high order feature bits, make sure that
virtio-net uses 64-bit values everywhere.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
---
hw/net/virtio-net.c | 54 +++++++++++++++++++++---------------------
include/hw/virtio/virtio-net.h | 2 +-
2 files changed, 28 insertions(+), 28 deletions(-)
diff --git a/hw/net/virtio-net.c b/hw/net/virtio-net.c
index 38674b0..adc20df 100644
--- a/hw/net/virtio-net.c
+++ b/hw/net/virtio-net.c
@@ -48,18 +48,18 @@
(offsetof(container, field) + sizeof(((container *)0)->field))
typedef struct VirtIOFeature {
- uint32_t flags;
+ uint64_t flags;
size_t end;
} VirtIOFeature;
static VirtIOFeature feature_sizes[] = {
- {.flags = 1 << VIRTIO_NET_F_MAC,
+ {.flags = 1ULL << VIRTIO_NET_F_MAC,
.end = endof(struct virtio_net_config, mac)},
- {.flags = 1 << VIRTIO_NET_F_STATUS,
+ {.flags = 1ULL << VIRTIO_NET_F_STATUS,
.end = endof(struct virtio_net_config, status)},
- {.flags = 1 << VIRTIO_NET_F_MQ,
+ {.flags = 1ULL << VIRTIO_NET_F_MQ,
.end = endof(struct virtio_net_config, max_virtqueue_pairs)},
- {.flags = 1 << VIRTIO_NET_F_MTU,
+ {.flags = 1ULL << VIRTIO_NET_F_MTU,
.end = endof(struct virtio_net_config, mtu)},
{}
};
@@ -1938,7 +1938,7 @@ static void virtio_net_device_realize(DeviceState *dev, Error **errp)
int i;
if (n->net_conf.mtu) {
- n->host_features |= (0x1 << VIRTIO_NET_F_MTU);
+ n->host_features |= (1ULL << VIRTIO_NET_F_MTU);
}
virtio_net_set_config_size(n, n->host_features);
@@ -2109,45 +2109,45 @@ static const VMStateDescription vmstate_virtio_net = {
};
static Property virtio_net_properties[] = {
- DEFINE_PROP_BIT("csum", VirtIONet, host_features, VIRTIO_NET_F_CSUM, true),
- DEFINE_PROP_BIT("guest_csum", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("csum", VirtIONet, host_features, VIRTIO_NET_F_CSUM, true),
+ DEFINE_PROP_BIT64("guest_csum", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_CSUM, true),
- DEFINE_PROP_BIT("gso", VirtIONet, host_features, VIRTIO_NET_F_GSO, true),
- DEFINE_PROP_BIT("guest_tso4", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("gso", VirtIONet, host_features, VIRTIO_NET_F_GSO, true),
+ DEFINE_PROP_BIT64("guest_tso4", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_TSO4, true),
- DEFINE_PROP_BIT("guest_tso6", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_tso6", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_TSO6, true),
- DEFINE_PROP_BIT("guest_ecn", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_ecn", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_ECN, true),
- DEFINE_PROP_BIT("guest_ufo", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_ufo", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_UFO, true),
- DEFINE_PROP_BIT("guest_announce", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("guest_announce", VirtIONet, host_features,
VIRTIO_NET_F_GUEST_ANNOUNCE, true),
- DEFINE_PROP_BIT("host_tso4", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_tso4", VirtIONet, host_features,
VIRTIO_NET_F_HOST_TSO4, true),
- DEFINE_PROP_BIT("host_tso6", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_tso6", VirtIONet, host_features,
VIRTIO_NET_F_HOST_TSO6, true),
- DEFINE_PROP_BIT("host_ecn", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_ecn", VirtIONet, host_features,
VIRTIO_NET_F_HOST_ECN, true),
- DEFINE_PROP_BIT("host_ufo", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("host_ufo", VirtIONet, host_features,
VIRTIO_NET_F_HOST_UFO, true),
- DEFINE_PROP_BIT("mrg_rxbuf", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("mrg_rxbuf", VirtIONet, host_features,
VIRTIO_NET_F_MRG_RXBUF, true),
- DEFINE_PROP_BIT("status", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("status", VirtIONet, host_features,
VIRTIO_NET_F_STATUS, true),
- DEFINE_PROP_BIT("ctrl_vq", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_vq", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_VQ, true),
- DEFINE_PROP_BIT("ctrl_rx", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_rx", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_RX, true),
- DEFINE_PROP_BIT("ctrl_vlan", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_vlan", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_VLAN, true),
- DEFINE_PROP_BIT("ctrl_rx_extra", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_rx_extra", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_RX_EXTRA, true),
- DEFINE_PROP_BIT("ctrl_mac_addr", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_mac_addr", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_MAC_ADDR, true),
- DEFINE_PROP_BIT("ctrl_guest_offloads", VirtIONet, host_features,
+ DEFINE_PROP_BIT64("ctrl_guest_offloads", VirtIONet, host_features,
VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, true),
- DEFINE_PROP_BIT("mq", VirtIONet, host_features, VIRTIO_NET_F_MQ, false),
+ DEFINE_PROP_BIT64("mq", VirtIONet, host_features, VIRTIO_NET_F_MQ, false),
DEFINE_NIC_PROPERTIES(VirtIONet, nic_conf),
DEFINE_PROP_UINT32("x-txtimer", VirtIONet, net_conf.txtimer,
TX_TIMER_INTERVAL),
diff --git a/include/hw/virtio/virtio-net.h b/include/hw/virtio/virtio-net.h
index b81b6a4..e7634c9 100644
--- a/include/hw/virtio/virtio-net.h
+++ b/include/hw/virtio/virtio-net.h
@@ -67,7 +67,7 @@ typedef struct VirtIONet {
uint32_t has_vnet_hdr;
size_t host_hdr_len;
size_t guest_hdr_len;
- uint32_t host_features;
+ uint64_t host_features;
uint8_t has_ufo;
uint32_t mergeable_rx_bufs;
uint8_t promisc;
--
2.6.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* [PATCH 3/3] qemu: add linkspeed and duplex settings to virtio-net
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
@ 2017-12-22 21:53 ` Jason Baron
-1 siblings, 0 replies; 26+ messages in thread
From: Jason Baron @ 2017-12-22 21:53 UTC (permalink / raw)
To: netdev, virtualization, qemu-devel; +Cc: mst, jasowang
Although linkspeed and duplex can be set in a linux guest via 'ethtool -s',
this requires custom ethtool commands for virtio-net by default.
Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
the hypervisor to export a linkspeed and duplex setting. The user can
subsequently overwrite it later if desired via: 'ethtool -s'.
Linkspeed and duplex settings can be set as:
'-device virtio-net,speed=10000,duplex=full'
where speed is [-1...INT_MAX], and duplex is ["half"|"full"].
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
---
hw/net/virtio-net.c | 29 +++++++++++++++++++++++++++++
include/hw/virtio/virtio-net.h | 3 +++
include/standard-headers/linux/virtio_net.h | 4 ++++
3 files changed, 36 insertions(+)
create mode 160000 pixman
diff --git a/hw/net/virtio-net.c b/hw/net/virtio-net.c
index adc20df..7fafe6e 100644
--- a/hw/net/virtio-net.c
+++ b/hw/net/virtio-net.c
@@ -40,6 +40,12 @@
#define VIRTIO_NET_RX_QUEUE_MIN_SIZE VIRTIO_NET_RX_QUEUE_DEFAULT_SIZE
#define VIRTIO_NET_TX_QUEUE_MIN_SIZE VIRTIO_NET_TX_QUEUE_DEFAULT_SIZE
+/* duplex and speed defines */
+#define DUPLEX_UNKNOWN 0xff
+#define DUPLEX_HALF 0x00
+#define DUPLEX_FULL 0x01
+#define SPEED_UNKNOWN -1
+
/*
* Calculate the number of bytes up to and including the given 'field' of
* 'container'.
@@ -61,6 +67,8 @@ static VirtIOFeature feature_sizes[] = {
.end = endof(struct virtio_net_config, max_virtqueue_pairs)},
{.flags = 1ULL << VIRTIO_NET_F_MTU,
.end = endof(struct virtio_net_config, mtu)},
+ {.flags = 1ULL << VIRTIO_NET_F_SPEED_DUPLEX,
+ .end = endof(struct virtio_net_config, duplex)},
{}
};
@@ -88,6 +96,8 @@ static void virtio_net_get_config(VirtIODevice *vdev, uint8_t *config)
virtio_stw_p(vdev, &netcfg.status, n->status);
virtio_stw_p(vdev, &netcfg.max_virtqueue_pairs, n->max_queues);
virtio_stw_p(vdev, &netcfg.mtu, n->net_conf.mtu);
+ virtio_stl_p(vdev, &netcfg.speed, n->net_conf.speed);
+ netcfg.duplex = n->net_conf.duplex;
memcpy(netcfg.mac, n->mac, ETH_ALEN);
memcpy(config, &netcfg, n->config_size);
}
@@ -1941,6 +1951,23 @@ static void virtio_net_device_realize(DeviceState *dev, Error **errp)
n->host_features |= (1ULL << VIRTIO_NET_F_MTU);
}
+ n->host_features |= (1ULL << VIRTIO_NET_F_SPEED_DUPLEX);
+ if (n->net_conf.duplex_str) {
+ if (strncmp(n->net_conf.duplex_str, "half", 5) == 0) {
+ n->net_conf.duplex = DUPLEX_HALF;
+ } else if (strncmp(n->net_conf.duplex_str, "full", 5) == 0) {
+ n->net_conf.duplex = DUPLEX_FULL;
+ } else {
+ error_setg(errp, "'duplex' must be 'half' or 'full'");
+ }
+ } else {
+ n->net_conf.duplex = DUPLEX_UNKNOWN;
+ }
+ if (n->net_conf.speed < SPEED_UNKNOWN) {
+ error_setg(errp, "'speed' must be between -1 (SPEED_UNKOWN) and "
+ "INT_MAX");
+ }
+
virtio_net_set_config_size(n, n->host_features);
virtio_init(vdev, "virtio-net", VIRTIO_ID_NET, n->config_size);
@@ -2160,6 +2187,8 @@ static Property virtio_net_properties[] = {
DEFINE_PROP_UINT16("host_mtu", VirtIONet, net_conf.mtu, 0),
DEFINE_PROP_BOOL("x-mtu-bypass-backend", VirtIONet, mtu_bypass_backend,
true),
+ DEFINE_PROP_INT32("speed", VirtIONet, net_conf.speed, SPEED_UNKNOWN),
+ DEFINE_PROP_STRING("duplex", VirtIONet, net_conf.duplex_str),
DEFINE_PROP_END_OF_LIST(),
};
diff --git a/include/hw/virtio/virtio-net.h b/include/hw/virtio/virtio-net.h
index e7634c9..02484dc 100644
--- a/include/hw/virtio/virtio-net.h
+++ b/include/hw/virtio/virtio-net.h
@@ -38,6 +38,9 @@ typedef struct virtio_net_conf
uint16_t rx_queue_size;
uint16_t tx_queue_size;
uint16_t mtu;
+ int32_t speed;
+ char *duplex_str;
+ uint8_t duplex;
} virtio_net_conf;
/* Maximum packet size we can receive from tap device: header + 64k */
diff --git a/include/standard-headers/linux/virtio_net.h b/include/standard-headers/linux/virtio_net.h
index 30ff249..0ff1447 100644
--- a/include/standard-headers/linux/virtio_net.h
+++ b/include/standard-headers/linux/virtio_net.h
@@ -36,6 +36,7 @@
#define VIRTIO_NET_F_GUEST_CSUM 1 /* Guest handles pkts w/ partial csum */
#define VIRTIO_NET_F_CTRL_GUEST_OFFLOADS 2 /* Dynamic offload configuration. */
#define VIRTIO_NET_F_MTU 3 /* Initial MTU advice */
+#define VIRTIO_NET_F_SPEED_DUPLEX 4 /* Host set linkspeed and duplex */
#define VIRTIO_NET_F_MAC 5 /* Host has given MAC address. */
#define VIRTIO_NET_F_GUEST_TSO4 7 /* Guest can handle TSOv4 in. */
#define VIRTIO_NET_F_GUEST_TSO6 8 /* Guest can handle TSOv6 in. */
@@ -76,6 +77,9 @@ struct virtio_net_config {
uint16_t max_virtqueue_pairs;
/* Default maximum transmit unit advice */
uint16_t mtu;
+ /* Host exported linkspeed and duplex */
+ uint32_t speed;
+ uint8_t duplex;
} QEMU_PACKED;
/*
^ permalink raw reply related [flat|nested] 26+ messages in thread* [Qemu-devel] [PATCH 3/3] qemu: add linkspeed and duplex settings to virtio-net
@ 2017-12-22 21:53 ` Jason Baron
0 siblings, 0 replies; 26+ messages in thread
From: Jason Baron @ 2017-12-22 21:53 UTC (permalink / raw)
To: netdev, virtualization, qemu-devel; +Cc: mst, jasowang
Although linkspeed and duplex can be set in a linux guest via 'ethtool -s',
this requires custom ethtool commands for virtio-net by default.
Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
the hypervisor to export a linkspeed and duplex setting. The user can
subsequently overwrite it later if desired via: 'ethtool -s'.
Linkspeed and duplex settings can be set as:
'-device virtio-net,speed=10000,duplex=full'
where speed is [-1...INT_MAX], and duplex is ["half"|"full"].
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
---
hw/net/virtio-net.c | 29 +++++++++++++++++++++++++++++
include/hw/virtio/virtio-net.h | 3 +++
include/standard-headers/linux/virtio_net.h | 4 ++++
3 files changed, 36 insertions(+)
create mode 160000 pixman
diff --git a/hw/net/virtio-net.c b/hw/net/virtio-net.c
index adc20df..7fafe6e 100644
--- a/hw/net/virtio-net.c
+++ b/hw/net/virtio-net.c
@@ -40,6 +40,12 @@
#define VIRTIO_NET_RX_QUEUE_MIN_SIZE VIRTIO_NET_RX_QUEUE_DEFAULT_SIZE
#define VIRTIO_NET_TX_QUEUE_MIN_SIZE VIRTIO_NET_TX_QUEUE_DEFAULT_SIZE
+/* duplex and speed defines */
+#define DUPLEX_UNKNOWN 0xff
+#define DUPLEX_HALF 0x00
+#define DUPLEX_FULL 0x01
+#define SPEED_UNKNOWN -1
+
/*
* Calculate the number of bytes up to and including the given 'field' of
* 'container'.
@@ -61,6 +67,8 @@ static VirtIOFeature feature_sizes[] = {
.end = endof(struct virtio_net_config, max_virtqueue_pairs)},
{.flags = 1ULL << VIRTIO_NET_F_MTU,
.end = endof(struct virtio_net_config, mtu)},
+ {.flags = 1ULL << VIRTIO_NET_F_SPEED_DUPLEX,
+ .end = endof(struct virtio_net_config, duplex)},
{}
};
@@ -88,6 +96,8 @@ static void virtio_net_get_config(VirtIODevice *vdev, uint8_t *config)
virtio_stw_p(vdev, &netcfg.status, n->status);
virtio_stw_p(vdev, &netcfg.max_virtqueue_pairs, n->max_queues);
virtio_stw_p(vdev, &netcfg.mtu, n->net_conf.mtu);
+ virtio_stl_p(vdev, &netcfg.speed, n->net_conf.speed);
+ netcfg.duplex = n->net_conf.duplex;
memcpy(netcfg.mac, n->mac, ETH_ALEN);
memcpy(config, &netcfg, n->config_size);
}
@@ -1941,6 +1951,23 @@ static void virtio_net_device_realize(DeviceState *dev, Error **errp)
n->host_features |= (1ULL << VIRTIO_NET_F_MTU);
}
+ n->host_features |= (1ULL << VIRTIO_NET_F_SPEED_DUPLEX);
+ if (n->net_conf.duplex_str) {
+ if (strncmp(n->net_conf.duplex_str, "half", 5) == 0) {
+ n->net_conf.duplex = DUPLEX_HALF;
+ } else if (strncmp(n->net_conf.duplex_str, "full", 5) == 0) {
+ n->net_conf.duplex = DUPLEX_FULL;
+ } else {
+ error_setg(errp, "'duplex' must be 'half' or 'full'");
+ }
+ } else {
+ n->net_conf.duplex = DUPLEX_UNKNOWN;
+ }
+ if (n->net_conf.speed < SPEED_UNKNOWN) {
+ error_setg(errp, "'speed' must be between -1 (SPEED_UNKOWN) and "
+ "INT_MAX");
+ }
+
virtio_net_set_config_size(n, n->host_features);
virtio_init(vdev, "virtio-net", VIRTIO_ID_NET, n->config_size);
@@ -2160,6 +2187,8 @@ static Property virtio_net_properties[] = {
DEFINE_PROP_UINT16("host_mtu", VirtIONet, net_conf.mtu, 0),
DEFINE_PROP_BOOL("x-mtu-bypass-backend", VirtIONet, mtu_bypass_backend,
true),
+ DEFINE_PROP_INT32("speed", VirtIONet, net_conf.speed, SPEED_UNKNOWN),
+ DEFINE_PROP_STRING("duplex", VirtIONet, net_conf.duplex_str),
DEFINE_PROP_END_OF_LIST(),
};
diff --git a/include/hw/virtio/virtio-net.h b/include/hw/virtio/virtio-net.h
index e7634c9..02484dc 100644
--- a/include/hw/virtio/virtio-net.h
+++ b/include/hw/virtio/virtio-net.h
@@ -38,6 +38,9 @@ typedef struct virtio_net_conf
uint16_t rx_queue_size;
uint16_t tx_queue_size;
uint16_t mtu;
+ int32_t speed;
+ char *duplex_str;
+ uint8_t duplex;
} virtio_net_conf;
/* Maximum packet size we can receive from tap device: header + 64k */
diff --git a/include/standard-headers/linux/virtio_net.h b/include/standard-headers/linux/virtio_net.h
index 30ff249..0ff1447 100644
--- a/include/standard-headers/linux/virtio_net.h
+++ b/include/standard-headers/linux/virtio_net.h
@@ -36,6 +36,7 @@
#define VIRTIO_NET_F_GUEST_CSUM 1 /* Guest handles pkts w/ partial csum */
#define VIRTIO_NET_F_CTRL_GUEST_OFFLOADS 2 /* Dynamic offload configuration. */
#define VIRTIO_NET_F_MTU 3 /* Initial MTU advice */
+#define VIRTIO_NET_F_SPEED_DUPLEX 4 /* Host set linkspeed and duplex */
#define VIRTIO_NET_F_MAC 5 /* Host has given MAC address. */
#define VIRTIO_NET_F_GUEST_TSO4 7 /* Guest can handle TSOv4 in. */
#define VIRTIO_NET_F_GUEST_TSO6 8 /* Guest can handle TSOv6 in. */
@@ -76,6 +77,9 @@ struct virtio_net_config {
uint16_t max_virtqueue_pairs;
/* Default maximum transmit unit advice */
uint16_t mtu;
+ /* Host exported linkspeed and duplex */
+ uint32_t speed;
+ uint8_t duplex;
} QEMU_PACKED;
/*
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 3/3] qemu: add linkspeed and duplex settings to virtio-net
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
` (3 preceding siblings ...)
(?)
@ 2017-12-22 21:53 ` Jason Baron via Virtualization
-1 siblings, 0 replies; 26+ messages in thread
From: Jason Baron via Virtualization @ 2017-12-22 21:53 UTC (permalink / raw)
To: netdev, virtualization, qemu-devel; +Cc: mst
Although linkspeed and duplex can be set in a linux guest via 'ethtool -s',
this requires custom ethtool commands for virtio-net by default.
Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
the hypervisor to export a linkspeed and duplex setting. The user can
subsequently overwrite it later if desired via: 'ethtool -s'.
Linkspeed and duplex settings can be set as:
'-device virtio-net,speed=10000,duplex=full'
where speed is [-1...INT_MAX], and duplex is ["half"|"full"].
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
---
hw/net/virtio-net.c | 29 +++++++++++++++++++++++++++++
include/hw/virtio/virtio-net.h | 3 +++
include/standard-headers/linux/virtio_net.h | 4 ++++
3 files changed, 36 insertions(+)
create mode 160000 pixman
diff --git a/hw/net/virtio-net.c b/hw/net/virtio-net.c
index adc20df..7fafe6e 100644
--- a/hw/net/virtio-net.c
+++ b/hw/net/virtio-net.c
@@ -40,6 +40,12 @@
#define VIRTIO_NET_RX_QUEUE_MIN_SIZE VIRTIO_NET_RX_QUEUE_DEFAULT_SIZE
#define VIRTIO_NET_TX_QUEUE_MIN_SIZE VIRTIO_NET_TX_QUEUE_DEFAULT_SIZE
+/* duplex and speed defines */
+#define DUPLEX_UNKNOWN 0xff
+#define DUPLEX_HALF 0x00
+#define DUPLEX_FULL 0x01
+#define SPEED_UNKNOWN -1
+
/*
* Calculate the number of bytes up to and including the given 'field' of
* 'container'.
@@ -61,6 +67,8 @@ static VirtIOFeature feature_sizes[] = {
.end = endof(struct virtio_net_config, max_virtqueue_pairs)},
{.flags = 1ULL << VIRTIO_NET_F_MTU,
.end = endof(struct virtio_net_config, mtu)},
+ {.flags = 1ULL << VIRTIO_NET_F_SPEED_DUPLEX,
+ .end = endof(struct virtio_net_config, duplex)},
{}
};
@@ -88,6 +96,8 @@ static void virtio_net_get_config(VirtIODevice *vdev, uint8_t *config)
virtio_stw_p(vdev, &netcfg.status, n->status);
virtio_stw_p(vdev, &netcfg.max_virtqueue_pairs, n->max_queues);
virtio_stw_p(vdev, &netcfg.mtu, n->net_conf.mtu);
+ virtio_stl_p(vdev, &netcfg.speed, n->net_conf.speed);
+ netcfg.duplex = n->net_conf.duplex;
memcpy(netcfg.mac, n->mac, ETH_ALEN);
memcpy(config, &netcfg, n->config_size);
}
@@ -1941,6 +1951,23 @@ static void virtio_net_device_realize(DeviceState *dev, Error **errp)
n->host_features |= (1ULL << VIRTIO_NET_F_MTU);
}
+ n->host_features |= (1ULL << VIRTIO_NET_F_SPEED_DUPLEX);
+ if (n->net_conf.duplex_str) {
+ if (strncmp(n->net_conf.duplex_str, "half", 5) == 0) {
+ n->net_conf.duplex = DUPLEX_HALF;
+ } else if (strncmp(n->net_conf.duplex_str, "full", 5) == 0) {
+ n->net_conf.duplex = DUPLEX_FULL;
+ } else {
+ error_setg(errp, "'duplex' must be 'half' or 'full'");
+ }
+ } else {
+ n->net_conf.duplex = DUPLEX_UNKNOWN;
+ }
+ if (n->net_conf.speed < SPEED_UNKNOWN) {
+ error_setg(errp, "'speed' must be between -1 (SPEED_UNKOWN) and "
+ "INT_MAX");
+ }
+
virtio_net_set_config_size(n, n->host_features);
virtio_init(vdev, "virtio-net", VIRTIO_ID_NET, n->config_size);
@@ -2160,6 +2187,8 @@ static Property virtio_net_properties[] = {
DEFINE_PROP_UINT16("host_mtu", VirtIONet, net_conf.mtu, 0),
DEFINE_PROP_BOOL("x-mtu-bypass-backend", VirtIONet, mtu_bypass_backend,
true),
+ DEFINE_PROP_INT32("speed", VirtIONet, net_conf.speed, SPEED_UNKNOWN),
+ DEFINE_PROP_STRING("duplex", VirtIONet, net_conf.duplex_str),
DEFINE_PROP_END_OF_LIST(),
};
diff --git a/include/hw/virtio/virtio-net.h b/include/hw/virtio/virtio-net.h
index e7634c9..02484dc 100644
--- a/include/hw/virtio/virtio-net.h
+++ b/include/hw/virtio/virtio-net.h
@@ -38,6 +38,9 @@ typedef struct virtio_net_conf
uint16_t rx_queue_size;
uint16_t tx_queue_size;
uint16_t mtu;
+ int32_t speed;
+ char *duplex_str;
+ uint8_t duplex;
} virtio_net_conf;
/* Maximum packet size we can receive from tap device: header + 64k */
diff --git a/include/standard-headers/linux/virtio_net.h b/include/standard-headers/linux/virtio_net.h
index 30ff249..0ff1447 100644
--- a/include/standard-headers/linux/virtio_net.h
+++ b/include/standard-headers/linux/virtio_net.h
@@ -36,6 +36,7 @@
#define VIRTIO_NET_F_GUEST_CSUM 1 /* Guest handles pkts w/ partial csum */
#define VIRTIO_NET_F_CTRL_GUEST_OFFLOADS 2 /* Dynamic offload configuration. */
#define VIRTIO_NET_F_MTU 3 /* Initial MTU advice */
+#define VIRTIO_NET_F_SPEED_DUPLEX 4 /* Host set linkspeed and duplex */
#define VIRTIO_NET_F_MAC 5 /* Host has given MAC address. */
#define VIRTIO_NET_F_GUEST_TSO4 7 /* Guest can handle TSOv4 in. */
#define VIRTIO_NET_F_GUEST_TSO6 8 /* Guest can handle TSOv6 in. */
@@ -76,6 +77,9 @@ struct virtio_net_config {
uint16_t max_virtqueue_pairs;
/* Default maximum transmit unit advice */
uint16_t mtu;
+ /* Host exported linkspeed and duplex */
+ uint32_t speed;
+ uint8_t duplex;
} QEMU_PACKED;
/*
^ permalink raw reply related [flat|nested] 26+ messages in thread* [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
@ 2017-12-22 21:54 ` Jason Baron
-1 siblings, 0 replies; 26+ messages in thread
From: Jason Baron @ 2017-12-22 21:54 UTC (permalink / raw)
To: netdev, virtualization, qemu-devel; +Cc: mst, jasowang
The ability to set speed and duplex for virtio_net in useful in various
scenarios as described here:
16032be virtio_net: add ethtool support for set and get of settings
However, it would be nice to be able to set this from the hypervisor,
such that virtio_net doesn't require custom guest ethtool commands.
Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
the hypervisor to export a linkspeed and duplex setting. The user can
subsequently overwrite it later if desired via: 'ethtool -s'.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
---
drivers/net/virtio_net.c | 17 ++++++++++++++++-
include/uapi/linux/virtio_net.h | 5 +++++
2 files changed, 21 insertions(+), 1 deletion(-)
diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
index 511f833..4168d82 100644
--- a/drivers/net/virtio_net.c
+++ b/drivers/net/virtio_net.c
@@ -2621,6 +2621,20 @@ static int virtnet_probe(struct virtio_device *vdev)
netif_set_real_num_rx_queues(dev, vi->curr_queue_pairs);
virtnet_init_settings(dev);
+ if (virtio_has_feature(vdev, VIRTIO_NET_F_SPEED_DUPLEX)) {
+ u32 speed;
+ u8 duplex;
+
+ speed = virtio_cread32(vdev, offsetof(struct virtio_net_config,
+ speed));
+ if (ethtool_validate_speed(speed))
+ vi->speed = speed;
+ duplex = virtio_cread8(vdev,
+ offsetof(struct virtio_net_config,
+ duplex));
+ if (ethtool_validate_duplex(duplex))
+ vi->duplex = duplex;
+ }
err = register_netdev(dev);
if (err) {
@@ -2746,7 +2760,8 @@ static struct virtio_device_id id_table[] = {
VIRTIO_NET_F_CTRL_RX, VIRTIO_NET_F_CTRL_VLAN, \
VIRTIO_NET_F_GUEST_ANNOUNCE, VIRTIO_NET_F_MQ, \
VIRTIO_NET_F_CTRL_MAC_ADDR, \
- VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
+ VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, \
+ VIRTIO_NET_F_SPEED_DUPLEX
static unsigned int features[] = {
VIRTNET_FEATURES,
diff --git a/include/uapi/linux/virtio_net.h b/include/uapi/linux/virtio_net.h
index fc353b5..0f1548e 100644
--- a/include/uapi/linux/virtio_net.h
+++ b/include/uapi/linux/virtio_net.h
@@ -57,6 +57,8 @@
* Steering */
#define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
+#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
+
#ifndef VIRTIO_NET_NO_LEGACY
#define VIRTIO_NET_F_GSO 6 /* Host handles pkts w/ any GSO type */
#endif /* VIRTIO_NET_NO_LEGACY */
@@ -76,6 +78,9 @@ struct virtio_net_config {
__u16 max_virtqueue_pairs;
/* Default maximum transmit unit advice */
__u16 mtu;
+ /* Host exported linkspeed and duplex */
+ __u32 speed;
+ __u8 duplex;
} __attribute__((packed));
/*
--
2.6.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* [Qemu-devel] [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
@ 2017-12-22 21:54 ` Jason Baron
0 siblings, 0 replies; 26+ messages in thread
From: Jason Baron @ 2017-12-22 21:54 UTC (permalink / raw)
To: netdev, virtualization, qemu-devel; +Cc: mst, jasowang
The ability to set speed and duplex for virtio_net in useful in various
scenarios as described here:
16032be virtio_net: add ethtool support for set and get of settings
However, it would be nice to be able to set this from the hypervisor,
such that virtio_net doesn't require custom guest ethtool commands.
Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
the hypervisor to export a linkspeed and duplex setting. The user can
subsequently overwrite it later if desired via: 'ethtool -s'.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
---
drivers/net/virtio_net.c | 17 ++++++++++++++++-
include/uapi/linux/virtio_net.h | 5 +++++
2 files changed, 21 insertions(+), 1 deletion(-)
diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
index 511f833..4168d82 100644
--- a/drivers/net/virtio_net.c
+++ b/drivers/net/virtio_net.c
@@ -2621,6 +2621,20 @@ static int virtnet_probe(struct virtio_device *vdev)
netif_set_real_num_rx_queues(dev, vi->curr_queue_pairs);
virtnet_init_settings(dev);
+ if (virtio_has_feature(vdev, VIRTIO_NET_F_SPEED_DUPLEX)) {
+ u32 speed;
+ u8 duplex;
+
+ speed = virtio_cread32(vdev, offsetof(struct virtio_net_config,
+ speed));
+ if (ethtool_validate_speed(speed))
+ vi->speed = speed;
+ duplex = virtio_cread8(vdev,
+ offsetof(struct virtio_net_config,
+ duplex));
+ if (ethtool_validate_duplex(duplex))
+ vi->duplex = duplex;
+ }
err = register_netdev(dev);
if (err) {
@@ -2746,7 +2760,8 @@ static struct virtio_device_id id_table[] = {
VIRTIO_NET_F_CTRL_RX, VIRTIO_NET_F_CTRL_VLAN, \
VIRTIO_NET_F_GUEST_ANNOUNCE, VIRTIO_NET_F_MQ, \
VIRTIO_NET_F_CTRL_MAC_ADDR, \
- VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
+ VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, \
+ VIRTIO_NET_F_SPEED_DUPLEX
static unsigned int features[] = {
VIRTNET_FEATURES,
diff --git a/include/uapi/linux/virtio_net.h b/include/uapi/linux/virtio_net.h
index fc353b5..0f1548e 100644
--- a/include/uapi/linux/virtio_net.h
+++ b/include/uapi/linux/virtio_net.h
@@ -57,6 +57,8 @@
* Steering */
#define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
+#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
+
#ifndef VIRTIO_NET_NO_LEGACY
#define VIRTIO_NET_F_GSO 6 /* Host handles pkts w/ any GSO type */
#endif /* VIRTIO_NET_NO_LEGACY */
@@ -76,6 +78,9 @@ struct virtio_net_config {
__u16 max_virtqueue_pairs;
/* Default maximum transmit unit advice */
__u16 mtu;
+ /* Host exported linkspeed and duplex */
+ __u32 speed;
+ __u8 duplex;
} __attribute__((packed));
/*
--
2.6.1
^ permalink raw reply related [flat|nested] 26+ messages in thread* Re: [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
@ 2017-12-27 21:43 ` David Miller
-1 siblings, 0 replies; 26+ messages in thread
From: David Miller @ 2017-12-27 21:43 UTC (permalink / raw)
To: jbaron; +Cc: netdev, virtualization, qemu-devel, mst, jasowang
From: Jason Baron <jbaron@akamai.com>
Date: Fri, 22 Dec 2017 16:54:01 -0500
> The ability to set speed and duplex for virtio_net in useful in various
> scenarios as described here:
>
> 16032be virtio_net: add ethtool support for set and get of settings
>
> However, it would be nice to be able to set this from the hypervisor,
> such that virtio_net doesn't require custom guest ethtool commands.
>
> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
> the hypervisor to export a linkspeed and duplex setting. The user can
> subsequently overwrite it later if desired via: 'ethtool -s'.
>
> Signed-off-by: Jason Baron <jbaron@akamai.com>
> Cc: "Michael S. Tsirkin" <mst@redhat.com>
> Cc: Jason Wang <jasowang@redhat.com>
Looks mostly fine to me but need some virtio_net reviewers on this one.
> @@ -57,6 +57,8 @@
> * Steering */
> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>
> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
> +
Why use a value so far away from the largest existing one?
Just curious.
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [Qemu-devel] [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
@ 2017-12-27 21:43 ` David Miller
0 siblings, 0 replies; 26+ messages in thread
From: David Miller @ 2017-12-27 21:43 UTC (permalink / raw)
To: jbaron; +Cc: netdev, virtualization, qemu-devel, mst, jasowang
From: Jason Baron <jbaron@akamai.com>
Date: Fri, 22 Dec 2017 16:54:01 -0500
> The ability to set speed and duplex for virtio_net in useful in various
> scenarios as described here:
>
> 16032be virtio_net: add ethtool support for set and get of settings
>
> However, it would be nice to be able to set this from the hypervisor,
> such that virtio_net doesn't require custom guest ethtool commands.
>
> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
> the hypervisor to export a linkspeed and duplex setting. The user can
> subsequently overwrite it later if desired via: 'ethtool -s'.
>
> Signed-off-by: Jason Baron <jbaron@akamai.com>
> Cc: "Michael S. Tsirkin" <mst@redhat.com>
> Cc: Jason Wang <jasowang@redhat.com>
Looks mostly fine to me but need some virtio_net reviewers on this one.
> @@ -57,6 +57,8 @@
> * Steering */
> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>
> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
> +
Why use a value so far away from the largest existing one?
Just curious.
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
2017-12-27 21:43 ` [Qemu-devel] " David Miller
@ 2017-12-28 15:53 ` Jason Baron
-1 siblings, 0 replies; 26+ messages in thread
From: Jason Baron @ 2017-12-28 15:53 UTC (permalink / raw)
To: David Miller; +Cc: netdev, virtualization, qemu-devel, mst, jasowang
On 12/27/2017 04:43 PM, David Miller wrote:
> From: Jason Baron <jbaron@akamai.com>
> Date: Fri, 22 Dec 2017 16:54:01 -0500
>
>> The ability to set speed and duplex for virtio_net in useful in various
>> scenarios as described here:
>>
>> 16032be virtio_net: add ethtool support for set and get of settings
>>
>> However, it would be nice to be able to set this from the hypervisor,
>> such that virtio_net doesn't require custom guest ethtool commands.
>>
>> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
>> the hypervisor to export a linkspeed and duplex setting. The user can
>> subsequently overwrite it later if desired via: 'ethtool -s'.
>>
>> Signed-off-by: Jason Baron <jbaron@akamai.com>
>> Cc: "Michael S. Tsirkin" <mst@redhat.com>
>> Cc: Jason Wang <jasowang@redhat.com>
>
> Looks mostly fine to me but need some virtio_net reviewers on this one.
>
>> @@ -57,6 +57,8 @@
>> * Steering */
>> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>>
>> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
>> +
>
> Why use a value so far away from the largest existing one?
>
> Just curious.
>
So that came from a discussion with Michael about which bit to use for
this, and he suggested using 63:
"
Transports started from bit 24 and are growing up.
So I would say devices should start from bit 63 and grow down.
"
https://patchwork.ozlabs.org/patch/848814/#1826669
I will add a comment to explain it.
Thanks,
-Jason
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [Qemu-devel] [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
@ 2017-12-28 15:53 ` Jason Baron
0 siblings, 0 replies; 26+ messages in thread
From: Jason Baron @ 2017-12-28 15:53 UTC (permalink / raw)
To: David Miller; +Cc: netdev, virtualization, qemu-devel, mst, jasowang
On 12/27/2017 04:43 PM, David Miller wrote:
> From: Jason Baron <jbaron@akamai.com>
> Date: Fri, 22 Dec 2017 16:54:01 -0500
>
>> The ability to set speed and duplex for virtio_net in useful in various
>> scenarios as described here:
>>
>> 16032be virtio_net: add ethtool support for set and get of settings
>>
>> However, it would be nice to be able to set this from the hypervisor,
>> such that virtio_net doesn't require custom guest ethtool commands.
>>
>> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
>> the hypervisor to export a linkspeed and duplex setting. The user can
>> subsequently overwrite it later if desired via: 'ethtool -s'.
>>
>> Signed-off-by: Jason Baron <jbaron@akamai.com>
>> Cc: "Michael S. Tsirkin" <mst@redhat.com>
>> Cc: Jason Wang <jasowang@redhat.com>
>
> Looks mostly fine to me but need some virtio_net reviewers on this one.
>
>> @@ -57,6 +57,8 @@
>> * Steering */
>> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>>
>> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
>> +
>
> Why use a value so far away from the largest existing one?
>
> Just curious.
>
So that came from a discussion with Michael about which bit to use for
this, and he suggested using 63:
"
Transports started from bit 24 and are growing up.
So I would say devices should start from bit 63 and grow down.
"
https://patchwork.ozlabs.org/patch/848814/#1826669
I will add a comment to explain it.
Thanks,
-Jason
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
2017-12-28 15:53 ` [Qemu-devel] " Jason Baron
@ 2018-01-03 13:49 ` Michael S. Tsirkin
-1 siblings, 0 replies; 26+ messages in thread
From: Michael S. Tsirkin @ 2018-01-03 13:49 UTC (permalink / raw)
To: Jason Baron; +Cc: qemu-devel, netdev, David Miller, virtualization
On Thu, Dec 28, 2017 at 10:53:54AM -0500, Jason Baron wrote:
>
>
> On 12/27/2017 04:43 PM, David Miller wrote:
> > From: Jason Baron <jbaron@akamai.com>
> > Date: Fri, 22 Dec 2017 16:54:01 -0500
> >
> >> The ability to set speed and duplex for virtio_net in useful in various
> >> scenarios as described here:
> >>
> >> 16032be virtio_net: add ethtool support for set and get of settings
> >>
> >> However, it would be nice to be able to set this from the hypervisor,
> >> such that virtio_net doesn't require custom guest ethtool commands.
> >>
> >> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
> >> the hypervisor to export a linkspeed and duplex setting. The user can
> >> subsequently overwrite it later if desired via: 'ethtool -s'.
> >>
> >> Signed-off-by: Jason Baron <jbaron@akamai.com>
> >> Cc: "Michael S. Tsirkin" <mst@redhat.com>
> >> Cc: Jason Wang <jasowang@redhat.com>
> >
> > Looks mostly fine to me but need some virtio_net reviewers on this one.
> >
> >> @@ -57,6 +57,8 @@
> >> * Steering */
> >> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
> >>
> >> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
> >> +
> >
> > Why use a value so far away from the largest existing one?
> >
> > Just curious.
> >
>
> So that came from a discussion with Michael about which bit to use for
> this, and he suggested using 63:
>
> "
> Transports started from bit 24 and are growing up.
> So I would say devices should start from bit 63 and grow down.
> "
>
> https://patchwork.ozlabs.org/patch/848814/#1826669
>
> I will add a comment to explain it.
Maybe in the commit log. I don't think we need it in the header.
> Thanks,
>
> -Jason
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [Qemu-devel] [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
@ 2018-01-03 13:49 ` Michael S. Tsirkin
0 siblings, 0 replies; 26+ messages in thread
From: Michael S. Tsirkin @ 2018-01-03 13:49 UTC (permalink / raw)
To: Jason Baron; +Cc: David Miller, netdev, virtualization, qemu-devel, jasowang
On Thu, Dec 28, 2017 at 10:53:54AM -0500, Jason Baron wrote:
>
>
> On 12/27/2017 04:43 PM, David Miller wrote:
> > From: Jason Baron <jbaron@akamai.com>
> > Date: Fri, 22 Dec 2017 16:54:01 -0500
> >
> >> The ability to set speed and duplex for virtio_net in useful in various
> >> scenarios as described here:
> >>
> >> 16032be virtio_net: add ethtool support for set and get of settings
> >>
> >> However, it would be nice to be able to set this from the hypervisor,
> >> such that virtio_net doesn't require custom guest ethtool commands.
> >>
> >> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
> >> the hypervisor to export a linkspeed and duplex setting. The user can
> >> subsequently overwrite it later if desired via: 'ethtool -s'.
> >>
> >> Signed-off-by: Jason Baron <jbaron@akamai.com>
> >> Cc: "Michael S. Tsirkin" <mst@redhat.com>
> >> Cc: Jason Wang <jasowang@redhat.com>
> >
> > Looks mostly fine to me but need some virtio_net reviewers on this one.
> >
> >> @@ -57,6 +57,8 @@
> >> * Steering */
> >> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
> >>
> >> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
> >> +
> >
> > Why use a value so far away from the largest existing one?
> >
> > Just curious.
> >
>
> So that came from a discussion with Michael about which bit to use for
> this, and he suggested using 63:
>
> "
> Transports started from bit 24 and are growing up.
> So I would say devices should start from bit 63 and grow down.
> "
>
> https://patchwork.ozlabs.org/patch/848814/#1826669
>
> I will add a comment to explain it.
Maybe in the commit log. I don't think we need it in the header.
> Thanks,
>
> -Jason
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
2017-12-27 21:43 ` [Qemu-devel] " David Miller
(?)
(?)
@ 2017-12-28 15:53 ` Jason Baron via Virtualization
-1 siblings, 0 replies; 26+ messages in thread
From: Jason Baron via Virtualization @ 2017-12-28 15:53 UTC (permalink / raw)
To: David Miller; +Cc: netdev, mst, qemu-devel, virtualization
On 12/27/2017 04:43 PM, David Miller wrote:
> From: Jason Baron <jbaron@akamai.com>
> Date: Fri, 22 Dec 2017 16:54:01 -0500
>
>> The ability to set speed and duplex for virtio_net in useful in various
>> scenarios as described here:
>>
>> 16032be virtio_net: add ethtool support for set and get of settings
>>
>> However, it would be nice to be able to set this from the hypervisor,
>> such that virtio_net doesn't require custom guest ethtool commands.
>>
>> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
>> the hypervisor to export a linkspeed and duplex setting. The user can
>> subsequently overwrite it later if desired via: 'ethtool -s'.
>>
>> Signed-off-by: Jason Baron <jbaron@akamai.com>
>> Cc: "Michael S. Tsirkin" <mst@redhat.com>
>> Cc: Jason Wang <jasowang@redhat.com>
>
> Looks mostly fine to me but need some virtio_net reviewers on this one.
>
>> @@ -57,6 +57,8 @@
>> * Steering */
>> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>>
>> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
>> +
>
> Why use a value so far away from the largest existing one?
>
> Just curious.
>
So that came from a discussion with Michael about which bit to use for
this, and he suggested using 63:
"
Transports started from bit 24 and are growing up.
So I would say devices should start from bit 63 and grow down.
"
https://patchwork.ozlabs.org/patch/848814/#1826669
I will add a comment to explain it.
Thanks,
-Jason
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
(?)
(?)
@ 2017-12-27 21:43 ` David Miller
-1 siblings, 0 replies; 26+ messages in thread
From: David Miller @ 2017-12-27 21:43 UTC (permalink / raw)
To: jbaron; +Cc: netdev, mst, qemu-devel, virtualization
From: Jason Baron <jbaron@akamai.com>
Date: Fri, 22 Dec 2017 16:54:01 -0500
> The ability to set speed and duplex for virtio_net in useful in various
> scenarios as described here:
>
> 16032be virtio_net: add ethtool support for set and get of settings
>
> However, it would be nice to be able to set this from the hypervisor,
> such that virtio_net doesn't require custom guest ethtool commands.
>
> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
> the hypervisor to export a linkspeed and duplex setting. The user can
> subsequently overwrite it later if desired via: 'ethtool -s'.
>
> Signed-off-by: Jason Baron <jbaron@akamai.com>
> Cc: "Michael S. Tsirkin" <mst@redhat.com>
> Cc: Jason Wang <jasowang@redhat.com>
Looks mostly fine to me but need some virtio_net reviewers on this one.
> @@ -57,6 +57,8 @@
> * Steering */
> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>
> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
> +
Why use a value so far away from the largest existing one?
Just curious.
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
` (2 preceding siblings ...)
(?)
@ 2018-01-03 14:01 ` Michael S. Tsirkin
-1 siblings, 0 replies; 26+ messages in thread
From: Michael S. Tsirkin @ 2018-01-03 14:01 UTC (permalink / raw)
To: Jason Baron; +Cc: netdev, qemu-devel, virtualization
On Fri, Dec 22, 2017 at 04:54:01PM -0500, Jason Baron wrote:
> The ability to set speed and duplex for virtio_net in useful in various
> scenarios as described here:
>
> 16032be virtio_net: add ethtool support for set and get of settings
>
> However, it would be nice to be able to set this from the hypervisor,
> such that virtio_net doesn't require custom guest ethtool commands.
>
> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
> the hypervisor to export a linkspeed and duplex setting. The user can
> subsequently overwrite it later if desired via: 'ethtool -s'.
>
> Signed-off-by: Jason Baron <jbaron@akamai.com>
> Cc: "Michael S. Tsirkin" <mst@redhat.com>
> Cc: Jason Wang <jasowang@redhat.com>
> ---
> drivers/net/virtio_net.c | 17 ++++++++++++++++-
> include/uapi/linux/virtio_net.h | 5 +++++
> 2 files changed, 21 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
> index 511f833..4168d82 100644
> --- a/drivers/net/virtio_net.c
> +++ b/drivers/net/virtio_net.c
> @@ -2621,6 +2621,20 @@ static int virtnet_probe(struct virtio_device *vdev)
> netif_set_real_num_rx_queues(dev, vi->curr_queue_pairs);
>
> virtnet_init_settings(dev);
> + if (virtio_has_feature(vdev, VIRTIO_NET_F_SPEED_DUPLEX)) {
> + u32 speed;
> + u8 duplex;
> +
> + speed = virtio_cread32(vdev, offsetof(struct virtio_net_config,
> + speed));
> + if (ethtool_validate_speed(speed))
> + vi->speed = speed;
> + duplex = virtio_cread8(vdev,
> + offsetof(struct virtio_net_config,
> + duplex));
> + if (ethtool_validate_duplex(duplex))
> + vi->duplex = duplex;
> + }
>
> err = register_netdev(dev);
> if (err) {
It would seem that speed/duplex can change at link up time.
Update it from virtnet_config_changed_work please.
> @@ -2746,7 +2760,8 @@ static struct virtio_device_id id_table[] = {
> VIRTIO_NET_F_CTRL_RX, VIRTIO_NET_F_CTRL_VLAN, \
> VIRTIO_NET_F_GUEST_ANNOUNCE, VIRTIO_NET_F_MQ, \
> VIRTIO_NET_F_CTRL_MAC_ADDR, \
> - VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
> + VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, \
> + VIRTIO_NET_F_SPEED_DUPLEX
>
> static unsigned int features[] = {
> VIRTNET_FEATURES,
> diff --git a/include/uapi/linux/virtio_net.h b/include/uapi/linux/virtio_net.h
> index fc353b5..0f1548e 100644
> --- a/include/uapi/linux/virtio_net.h
> +++ b/include/uapi/linux/virtio_net.h
> @@ -57,6 +57,8 @@
> * Steering */
> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>
> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
> +
Host -> device, to match virtio spec terminology.
> #ifndef VIRTIO_NET_NO_LEGACY
> #define VIRTIO_NET_F_GSO 6 /* Host handles pkts w/ any GSO type */
> #endif /* VIRTIO_NET_NO_LEGACY */
> @@ -76,6 +78,9 @@ struct virtio_net_config {
> __u16 max_virtqueue_pairs;
> /* Default maximum transmit unit advice */
> __u16 mtu;
> + /* Host exported linkspeed and duplex */
I would rather drop this and document each field.
/*
speed, in units of 1Mb. All values 0 to INT_MAX are legal.
Any other value stands for unknown.
*/
> + __u32 speed;
/*
0x00 - half duplex
0x01 - full duplex
Any other value stands for unknown.
*/
> + __u8 duplex;
> } __attribute__((packed));
>
> /*
> --
> 2.6.1
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
@ 2018-01-03 14:01 ` Michael S. Tsirkin
-1 siblings, 0 replies; 26+ messages in thread
From: Michael S. Tsirkin @ 2018-01-03 14:01 UTC (permalink / raw)
To: Jason Baron; +Cc: netdev, virtualization, qemu-devel, jasowang
On Fri, Dec 22, 2017 at 04:54:01PM -0500, Jason Baron wrote:
> The ability to set speed and duplex for virtio_net in useful in various
> scenarios as described here:
>
> 16032be virtio_net: add ethtool support for set and get of settings
>
> However, it would be nice to be able to set this from the hypervisor,
> such that virtio_net doesn't require custom guest ethtool commands.
>
> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
> the hypervisor to export a linkspeed and duplex setting. The user can
> subsequently overwrite it later if desired via: 'ethtool -s'.
>
> Signed-off-by: Jason Baron <jbaron@akamai.com>
> Cc: "Michael S. Tsirkin" <mst@redhat.com>
> Cc: Jason Wang <jasowang@redhat.com>
> ---
> drivers/net/virtio_net.c | 17 ++++++++++++++++-
> include/uapi/linux/virtio_net.h | 5 +++++
> 2 files changed, 21 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
> index 511f833..4168d82 100644
> --- a/drivers/net/virtio_net.c
> +++ b/drivers/net/virtio_net.c
> @@ -2621,6 +2621,20 @@ static int virtnet_probe(struct virtio_device *vdev)
> netif_set_real_num_rx_queues(dev, vi->curr_queue_pairs);
>
> virtnet_init_settings(dev);
> + if (virtio_has_feature(vdev, VIRTIO_NET_F_SPEED_DUPLEX)) {
> + u32 speed;
> + u8 duplex;
> +
> + speed = virtio_cread32(vdev, offsetof(struct virtio_net_config,
> + speed));
> + if (ethtool_validate_speed(speed))
> + vi->speed = speed;
> + duplex = virtio_cread8(vdev,
> + offsetof(struct virtio_net_config,
> + duplex));
> + if (ethtool_validate_duplex(duplex))
> + vi->duplex = duplex;
> + }
>
> err = register_netdev(dev);
> if (err) {
It would seem that speed/duplex can change at link up time.
Update it from virtnet_config_changed_work please.
> @@ -2746,7 +2760,8 @@ static struct virtio_device_id id_table[] = {
> VIRTIO_NET_F_CTRL_RX, VIRTIO_NET_F_CTRL_VLAN, \
> VIRTIO_NET_F_GUEST_ANNOUNCE, VIRTIO_NET_F_MQ, \
> VIRTIO_NET_F_CTRL_MAC_ADDR, \
> - VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
> + VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, \
> + VIRTIO_NET_F_SPEED_DUPLEX
>
> static unsigned int features[] = {
> VIRTNET_FEATURES,
> diff --git a/include/uapi/linux/virtio_net.h b/include/uapi/linux/virtio_net.h
> index fc353b5..0f1548e 100644
> --- a/include/uapi/linux/virtio_net.h
> +++ b/include/uapi/linux/virtio_net.h
> @@ -57,6 +57,8 @@
> * Steering */
> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>
> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
> +
Host -> device, to match virtio spec terminology.
> #ifndef VIRTIO_NET_NO_LEGACY
> #define VIRTIO_NET_F_GSO 6 /* Host handles pkts w/ any GSO type */
> #endif /* VIRTIO_NET_NO_LEGACY */
> @@ -76,6 +78,9 @@ struct virtio_net_config {
> __u16 max_virtqueue_pairs;
> /* Default maximum transmit unit advice */
> __u16 mtu;
> + /* Host exported linkspeed and duplex */
I would rather drop this and document each field.
/*
speed, in units of 1Mb. All values 0 to INT_MAX are legal.
Any other value stands for unknown.
*/
> + __u32 speed;
/*
0x00 - half duplex
0x01 - full duplex
Any other value stands for unknown.
*/
> + __u8 duplex;
> } __attribute__((packed));
>
> /*
> --
> 2.6.1
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [Qemu-devel] [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
@ 2018-01-03 14:01 ` Michael S. Tsirkin
0 siblings, 0 replies; 26+ messages in thread
From: Michael S. Tsirkin @ 2018-01-03 14:01 UTC (permalink / raw)
To: Jason Baron; +Cc: netdev, virtualization, qemu-devel, jasowang
On Fri, Dec 22, 2017 at 04:54:01PM -0500, Jason Baron wrote:
> The ability to set speed and duplex for virtio_net in useful in various
> scenarios as described here:
>
> 16032be virtio_net: add ethtool support for set and get of settings
>
> However, it would be nice to be able to set this from the hypervisor,
> such that virtio_net doesn't require custom guest ethtool commands.
>
> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
> the hypervisor to export a linkspeed and duplex setting. The user can
> subsequently overwrite it later if desired via: 'ethtool -s'.
>
> Signed-off-by: Jason Baron <jbaron@akamai.com>
> Cc: "Michael S. Tsirkin" <mst@redhat.com>
> Cc: Jason Wang <jasowang@redhat.com>
> ---
> drivers/net/virtio_net.c | 17 ++++++++++++++++-
> include/uapi/linux/virtio_net.h | 5 +++++
> 2 files changed, 21 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
> index 511f833..4168d82 100644
> --- a/drivers/net/virtio_net.c
> +++ b/drivers/net/virtio_net.c
> @@ -2621,6 +2621,20 @@ static int virtnet_probe(struct virtio_device *vdev)
> netif_set_real_num_rx_queues(dev, vi->curr_queue_pairs);
>
> virtnet_init_settings(dev);
> + if (virtio_has_feature(vdev, VIRTIO_NET_F_SPEED_DUPLEX)) {
> + u32 speed;
> + u8 duplex;
> +
> + speed = virtio_cread32(vdev, offsetof(struct virtio_net_config,
> + speed));
> + if (ethtool_validate_speed(speed))
> + vi->speed = speed;
> + duplex = virtio_cread8(vdev,
> + offsetof(struct virtio_net_config,
> + duplex));
> + if (ethtool_validate_duplex(duplex))
> + vi->duplex = duplex;
> + }
>
> err = register_netdev(dev);
> if (err) {
It would seem that speed/duplex can change at link up time.
Update it from virtnet_config_changed_work please.
> @@ -2746,7 +2760,8 @@ static struct virtio_device_id id_table[] = {
> VIRTIO_NET_F_CTRL_RX, VIRTIO_NET_F_CTRL_VLAN, \
> VIRTIO_NET_F_GUEST_ANNOUNCE, VIRTIO_NET_F_MQ, \
> VIRTIO_NET_F_CTRL_MAC_ADDR, \
> - VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
> + VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, \
> + VIRTIO_NET_F_SPEED_DUPLEX
>
> static unsigned int features[] = {
> VIRTNET_FEATURES,
> diff --git a/include/uapi/linux/virtio_net.h b/include/uapi/linux/virtio_net.h
> index fc353b5..0f1548e 100644
> --- a/include/uapi/linux/virtio_net.h
> +++ b/include/uapi/linux/virtio_net.h
> @@ -57,6 +57,8 @@
> * Steering */
> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>
> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
> +
Host -> device, to match virtio spec terminology.
> #ifndef VIRTIO_NET_NO_LEGACY
> #define VIRTIO_NET_F_GSO 6 /* Host handles pkts w/ any GSO type */
> #endif /* VIRTIO_NET_NO_LEGACY */
> @@ -76,6 +78,9 @@ struct virtio_net_config {
> __u16 max_virtqueue_pairs;
> /* Default maximum transmit unit advice */
> __u16 mtu;
> + /* Host exported linkspeed and duplex */
I would rather drop this and document each field.
/*
speed, in units of 1Mb. All values 0 to INT_MAX are legal.
Any other value stands for unknown.
*/
> + __u32 speed;
/*
0x00 - half duplex
0x01 - full duplex
Any other value stands for unknown.
*/
> + __u8 duplex;
> } __attribute__((packed));
>
> /*
> --
> 2.6.1
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
@ 2018-01-03 14:03 ` Michael S. Tsirkin
-1 siblings, 0 replies; 26+ messages in thread
From: Michael S. Tsirkin @ 2018-01-03 14:03 UTC (permalink / raw)
To: Jason Baron; +Cc: netdev, virtualization, qemu-devel, jasowang
On Fri, Dec 22, 2017 at 04:54:01PM -0500, Jason Baron wrote:
> The ability to set speed and duplex for virtio_net in useful in various
> scenarios as described here:
>
> 16032be virtio_net: add ethtool support for set and get of settings
>
> However, it would be nice to be able to set this from the hypervisor,
> such that virtio_net doesn't require custom guest ethtool commands.
>
> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
> the hypervisor to export a linkspeed and duplex setting. The user can
> subsequently overwrite it later if desired via: 'ethtool -s'.
>
> Signed-off-by: Jason Baron <jbaron@akamai.com>
> Cc: "Michael S. Tsirkin" <mst@redhat.com>
> Cc: Jason Wang <jasowang@redhat.com>
Same as any host/guest API change, please send a copy to the virtio TC
to make sure we avoid conflicts.
> ---
> drivers/net/virtio_net.c | 17 ++++++++++++++++-
> include/uapi/linux/virtio_net.h | 5 +++++
> 2 files changed, 21 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
> index 511f833..4168d82 100644
> --- a/drivers/net/virtio_net.c
> +++ b/drivers/net/virtio_net.c
> @@ -2621,6 +2621,20 @@ static int virtnet_probe(struct virtio_device *vdev)
> netif_set_real_num_rx_queues(dev, vi->curr_queue_pairs);
>
> virtnet_init_settings(dev);
> + if (virtio_has_feature(vdev, VIRTIO_NET_F_SPEED_DUPLEX)) {
> + u32 speed;
> + u8 duplex;
> +
> + speed = virtio_cread32(vdev, offsetof(struct virtio_net_config,
> + speed));
> + if (ethtool_validate_speed(speed))
> + vi->speed = speed;
> + duplex = virtio_cread8(vdev,
> + offsetof(struct virtio_net_config,
> + duplex));
> + if (ethtool_validate_duplex(duplex))
> + vi->duplex = duplex;
> + }
>
> err = register_netdev(dev);
> if (err) {
> @@ -2746,7 +2760,8 @@ static struct virtio_device_id id_table[] = {
> VIRTIO_NET_F_CTRL_RX, VIRTIO_NET_F_CTRL_VLAN, \
> VIRTIO_NET_F_GUEST_ANNOUNCE, VIRTIO_NET_F_MQ, \
> VIRTIO_NET_F_CTRL_MAC_ADDR, \
> - VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
> + VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, \
> + VIRTIO_NET_F_SPEED_DUPLEX
>
> static unsigned int features[] = {
> VIRTNET_FEATURES,
> diff --git a/include/uapi/linux/virtio_net.h b/include/uapi/linux/virtio_net.h
> index fc353b5..0f1548e 100644
> --- a/include/uapi/linux/virtio_net.h
> +++ b/include/uapi/linux/virtio_net.h
> @@ -57,6 +57,8 @@
> * Steering */
> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>
> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
> +
> #ifndef VIRTIO_NET_NO_LEGACY
> #define VIRTIO_NET_F_GSO 6 /* Host handles pkts w/ any GSO type */
> #endif /* VIRTIO_NET_NO_LEGACY */
> @@ -76,6 +78,9 @@ struct virtio_net_config {
> __u16 max_virtqueue_pairs;
> /* Default maximum transmit unit advice */
> __u16 mtu;
> + /* Host exported linkspeed and duplex */
> + __u32 speed;
> + __u8 duplex;
> } __attribute__((packed));
>
> /*
> --
> 2.6.1
^ permalink raw reply [flat|nested] 26+ messages in thread* Re: [Qemu-devel] [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
@ 2018-01-03 14:03 ` Michael S. Tsirkin
0 siblings, 0 replies; 26+ messages in thread
From: Michael S. Tsirkin @ 2018-01-03 14:03 UTC (permalink / raw)
To: Jason Baron; +Cc: netdev, virtualization, qemu-devel, jasowang
On Fri, Dec 22, 2017 at 04:54:01PM -0500, Jason Baron wrote:
> The ability to set speed and duplex for virtio_net in useful in various
> scenarios as described here:
>
> 16032be virtio_net: add ethtool support for set and get of settings
>
> However, it would be nice to be able to set this from the hypervisor,
> such that virtio_net doesn't require custom guest ethtool commands.
>
> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
> the hypervisor to export a linkspeed and duplex setting. The user can
> subsequently overwrite it later if desired via: 'ethtool -s'.
>
> Signed-off-by: Jason Baron <jbaron@akamai.com>
> Cc: "Michael S. Tsirkin" <mst@redhat.com>
> Cc: Jason Wang <jasowang@redhat.com>
Same as any host/guest API change, please send a copy to the virtio TC
to make sure we avoid conflicts.
> ---
> drivers/net/virtio_net.c | 17 ++++++++++++++++-
> include/uapi/linux/virtio_net.h | 5 +++++
> 2 files changed, 21 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
> index 511f833..4168d82 100644
> --- a/drivers/net/virtio_net.c
> +++ b/drivers/net/virtio_net.c
> @@ -2621,6 +2621,20 @@ static int virtnet_probe(struct virtio_device *vdev)
> netif_set_real_num_rx_queues(dev, vi->curr_queue_pairs);
>
> virtnet_init_settings(dev);
> + if (virtio_has_feature(vdev, VIRTIO_NET_F_SPEED_DUPLEX)) {
> + u32 speed;
> + u8 duplex;
> +
> + speed = virtio_cread32(vdev, offsetof(struct virtio_net_config,
> + speed));
> + if (ethtool_validate_speed(speed))
> + vi->speed = speed;
> + duplex = virtio_cread8(vdev,
> + offsetof(struct virtio_net_config,
> + duplex));
> + if (ethtool_validate_duplex(duplex))
> + vi->duplex = duplex;
> + }
>
> err = register_netdev(dev);
> if (err) {
> @@ -2746,7 +2760,8 @@ static struct virtio_device_id id_table[] = {
> VIRTIO_NET_F_CTRL_RX, VIRTIO_NET_F_CTRL_VLAN, \
> VIRTIO_NET_F_GUEST_ANNOUNCE, VIRTIO_NET_F_MQ, \
> VIRTIO_NET_F_CTRL_MAC_ADDR, \
> - VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
> + VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, \
> + VIRTIO_NET_F_SPEED_DUPLEX
>
> static unsigned int features[] = {
> VIRTNET_FEATURES,
> diff --git a/include/uapi/linux/virtio_net.h b/include/uapi/linux/virtio_net.h
> index fc353b5..0f1548e 100644
> --- a/include/uapi/linux/virtio_net.h
> +++ b/include/uapi/linux/virtio_net.h
> @@ -57,6 +57,8 @@
> * Steering */
> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>
> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
> +
> #ifndef VIRTIO_NET_NO_LEGACY
> #define VIRTIO_NET_F_GSO 6 /* Host handles pkts w/ any GSO type */
> #endif /* VIRTIO_NET_NO_LEGACY */
> @@ -76,6 +78,9 @@ struct virtio_net_config {
> __u16 max_virtqueue_pairs;
> /* Default maximum transmit unit advice */
> __u16 mtu;
> + /* Host exported linkspeed and duplex */
> + __u32 speed;
> + __u8 duplex;
> } __attribute__((packed));
>
> /*
> --
> 2.6.1
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
` (5 preceding siblings ...)
(?)
@ 2018-01-03 14:03 ` Michael S. Tsirkin
-1 siblings, 0 replies; 26+ messages in thread
From: Michael S. Tsirkin @ 2018-01-03 14:03 UTC (permalink / raw)
To: Jason Baron; +Cc: netdev, qemu-devel, virtualization
On Fri, Dec 22, 2017 at 04:54:01PM -0500, Jason Baron wrote:
> The ability to set speed and duplex for virtio_net in useful in various
> scenarios as described here:
>
> 16032be virtio_net: add ethtool support for set and get of settings
>
> However, it would be nice to be able to set this from the hypervisor,
> such that virtio_net doesn't require custom guest ethtool commands.
>
> Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
> the hypervisor to export a linkspeed and duplex setting. The user can
> subsequently overwrite it later if desired via: 'ethtool -s'.
>
> Signed-off-by: Jason Baron <jbaron@akamai.com>
> Cc: "Michael S. Tsirkin" <mst@redhat.com>
> Cc: Jason Wang <jasowang@redhat.com>
Same as any host/guest API change, please send a copy to the virtio TC
to make sure we avoid conflicts.
> ---
> drivers/net/virtio_net.c | 17 ++++++++++++++++-
> include/uapi/linux/virtio_net.h | 5 +++++
> 2 files changed, 21 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
> index 511f833..4168d82 100644
> --- a/drivers/net/virtio_net.c
> +++ b/drivers/net/virtio_net.c
> @@ -2621,6 +2621,20 @@ static int virtnet_probe(struct virtio_device *vdev)
> netif_set_real_num_rx_queues(dev, vi->curr_queue_pairs);
>
> virtnet_init_settings(dev);
> + if (virtio_has_feature(vdev, VIRTIO_NET_F_SPEED_DUPLEX)) {
> + u32 speed;
> + u8 duplex;
> +
> + speed = virtio_cread32(vdev, offsetof(struct virtio_net_config,
> + speed));
> + if (ethtool_validate_speed(speed))
> + vi->speed = speed;
> + duplex = virtio_cread8(vdev,
> + offsetof(struct virtio_net_config,
> + duplex));
> + if (ethtool_validate_duplex(duplex))
> + vi->duplex = duplex;
> + }
>
> err = register_netdev(dev);
> if (err) {
> @@ -2746,7 +2760,8 @@ static struct virtio_device_id id_table[] = {
> VIRTIO_NET_F_CTRL_RX, VIRTIO_NET_F_CTRL_VLAN, \
> VIRTIO_NET_F_GUEST_ANNOUNCE, VIRTIO_NET_F_MQ, \
> VIRTIO_NET_F_CTRL_MAC_ADDR, \
> - VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
> + VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, \
> + VIRTIO_NET_F_SPEED_DUPLEX
>
> static unsigned int features[] = {
> VIRTNET_FEATURES,
> diff --git a/include/uapi/linux/virtio_net.h b/include/uapi/linux/virtio_net.h
> index fc353b5..0f1548e 100644
> --- a/include/uapi/linux/virtio_net.h
> +++ b/include/uapi/linux/virtio_net.h
> @@ -57,6 +57,8 @@
> * Steering */
> #define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
>
> +#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
> +
> #ifndef VIRTIO_NET_NO_LEGACY
> #define VIRTIO_NET_F_GSO 6 /* Host handles pkts w/ any GSO type */
> #endif /* VIRTIO_NET_NO_LEGACY */
> @@ -76,6 +78,9 @@ struct virtio_net_config {
> __u16 max_virtqueue_pairs;
> /* Default maximum transmit unit advice */
> __u16 mtu;
> + /* Host exported linkspeed and duplex */
> + __u32 speed;
> + __u8 duplex;
> } __attribute__((packed));
>
> /*
> --
> 2.6.1
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH net-next v2 1/3] virtio_net: propagate linkspeed/duplex settings from the hypervisor
2017-12-22 21:54 ` [Qemu-devel] " Jason Baron
` (5 preceding siblings ...)
(?)
@ 2017-12-22 21:54 ` Jason Baron via Virtualization
-1 siblings, 0 replies; 26+ messages in thread
From: Jason Baron via Virtualization @ 2017-12-22 21:54 UTC (permalink / raw)
To: netdev, virtualization, qemu-devel; +Cc: mst
The ability to set speed and duplex for virtio_net in useful in various
scenarios as described here:
16032be virtio_net: add ethtool support for set and get of settings
However, it would be nice to be able to set this from the hypervisor,
such that virtio_net doesn't require custom guest ethtool commands.
Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
the hypervisor to export a linkspeed and duplex setting. The user can
subsequently overwrite it later if desired via: 'ethtool -s'.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
---
drivers/net/virtio_net.c | 17 ++++++++++++++++-
include/uapi/linux/virtio_net.h | 5 +++++
2 files changed, 21 insertions(+), 1 deletion(-)
diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c
index 511f833..4168d82 100644
--- a/drivers/net/virtio_net.c
+++ b/drivers/net/virtio_net.c
@@ -2621,6 +2621,20 @@ static int virtnet_probe(struct virtio_device *vdev)
netif_set_real_num_rx_queues(dev, vi->curr_queue_pairs);
virtnet_init_settings(dev);
+ if (virtio_has_feature(vdev, VIRTIO_NET_F_SPEED_DUPLEX)) {
+ u32 speed;
+ u8 duplex;
+
+ speed = virtio_cread32(vdev, offsetof(struct virtio_net_config,
+ speed));
+ if (ethtool_validate_speed(speed))
+ vi->speed = speed;
+ duplex = virtio_cread8(vdev,
+ offsetof(struct virtio_net_config,
+ duplex));
+ if (ethtool_validate_duplex(duplex))
+ vi->duplex = duplex;
+ }
err = register_netdev(dev);
if (err) {
@@ -2746,7 +2760,8 @@ static struct virtio_device_id id_table[] = {
VIRTIO_NET_F_CTRL_RX, VIRTIO_NET_F_CTRL_VLAN, \
VIRTIO_NET_F_GUEST_ANNOUNCE, VIRTIO_NET_F_MQ, \
VIRTIO_NET_F_CTRL_MAC_ADDR, \
- VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS
+ VIRTIO_NET_F_MTU, VIRTIO_NET_F_CTRL_GUEST_OFFLOADS, \
+ VIRTIO_NET_F_SPEED_DUPLEX
static unsigned int features[] = {
VIRTNET_FEATURES,
diff --git a/include/uapi/linux/virtio_net.h b/include/uapi/linux/virtio_net.h
index fc353b5..0f1548e 100644
--- a/include/uapi/linux/virtio_net.h
+++ b/include/uapi/linux/virtio_net.h
@@ -57,6 +57,8 @@
* Steering */
#define VIRTIO_NET_F_CTRL_MAC_ADDR 23 /* Set MAC address */
+#define VIRTIO_NET_F_SPEED_DUPLEX 63 /* Host set linkspeed and duplex */
+
#ifndef VIRTIO_NET_NO_LEGACY
#define VIRTIO_NET_F_GSO 6 /* Host handles pkts w/ any GSO type */
#endif /* VIRTIO_NET_NO_LEGACY */
@@ -76,6 +78,9 @@ struct virtio_net_config {
__u16 max_virtqueue_pairs;
/* Default maximum transmit unit advice */
__u16 mtu;
+ /* Host exported linkspeed and duplex */
+ __u32 speed;
+ __u8 duplex;
} __attribute__((packed));
/*
--
2.6.1
^ permalink raw reply related [flat|nested] 26+ messages in thread