From: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org, Ralf Baechle <ralf@linux-mips.org>,
Linux MIPS <linux-mips@linux-mips.org>,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v3] pinctrl: Add Microsemi Ocelot SoC driver
Date: Tue, 9 Jan 2018 15:07:05 +0100 [thread overview]
Message-ID: <20180109140705.GC2719@piout.net> (raw)
In-Reply-To: <CACRpkdaCfjW7hWS1VnC6MR+j48=Q0uo7OSMA_6G90D7Cz7NMZA@mail.gmail.com>
On 09/01/2018 at 14:56:36 +0100, Linus Walleij wrote:
> On Sat, Jan 6, 2018 at 1:09 AM, Alexandre Belloni
> <alexandre.belloni@free-electrons.com> wrote:
>
> > The Microsemi Ocelot SoC has a few pins that can be used as GPIOs or take
> > multiple other functions. Add a driver for the pinmuxing and the GPIOs.
> >
> > There is currently no support for interrupts.
> >
> > Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
> > ---
> > - use pinctrl_gpio_direction_input/output from
> > ocelot_gpio_direction_input/output
> > - add a comment for ALT0/ALT1
> > - fill .max_register of ocelot_pinctrl_regmap_config
>
> Patch applied. And it looks very good too.
>
> This was all I had to do, right? No dependent patches?
>
Nothing more for you, thanks! I'll get back to this driver if there is
interest in having IRQ support but I don't think this will happen soon.
--
Alexandre Belloni, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
next prev parent reply other threads:[~2018-01-09 14:07 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-08 15:46 [PATCH v2 00/13] MIPS: add support for the Microsemi MIPS SoCs Alexandre Belloni
2017-12-08 15:46 ` [PATCH v2 01/13] dt-bindings: Add vendor prefix for Microsemi Corporation Alexandre Belloni
2017-12-08 15:46 ` [PATCH v2 02/13] dt-bindings: interrupt-controller: Add binding for the Microsemi Ocelot interrupt controller Alexandre Belloni
2017-12-08 15:46 ` [PATCH v2 03/13] irqchip: Add a driver for the Microsemi Ocelot controller Alexandre Belloni
2017-12-08 15:46 ` [PATCH v2 04/13] dt-bindings: pinctrl: Add bindings for Microsemi Ocelot Alexandre Belloni
2017-12-13 7:39 ` Linus Walleij
2017-12-08 15:46 ` [PATCH v2 05/13] pinctrl: Add Microsemi Ocelot SoC driver Alexandre Belloni
2017-12-13 8:15 ` Linus Walleij
2017-12-13 9:23 ` Philippe Ombredanne
2017-12-14 23:53 ` Linus Walleij
2017-12-15 7:59 ` Philippe Ombredanne
2017-12-18 16:09 ` Alexandre Belloni
2018-01-05 23:46 ` Alexandre Belloni
2018-01-06 0:09 ` [PATCH v3] " Alexandre Belloni
2018-01-09 13:56 ` Linus Walleij
2018-01-09 14:07 ` Alexandre Belloni [this message]
2017-12-08 15:46 ` [PATCH v2 06/13] dt-bindings: mips: Add bindings for Microsemi SoCs Alexandre Belloni
2017-12-13 0:44 ` Rob Herring
2017-12-08 15:46 ` [PATCH v2 07/13] dt-bindings: power: reset: Document ocelot-reset binding Alexandre Belloni
2017-12-15 20:23 ` Rob Herring
2017-12-15 20:23 ` Rob Herring
2017-12-15 22:07 ` Alexandre Belloni
2017-12-15 22:07 ` Alexandre Belloni
2017-12-08 15:46 ` [PATCH v2 08/13] power: reset: Add a driver for the Microsemi Ocelot reset Alexandre Belloni
2017-12-08 17:07 ` Sebastian Reichel
2017-12-08 17:15 ` Alexandre Belloni
2017-12-18 13:26 ` PrasannaKumar Muralidharan
2017-12-08 15:46 ` [PATCH v2 09/13] MIPS: mscc: Add initial support for Microsemi MIPS SoCs Alexandre Belloni
2017-12-18 13:23 ` PrasannaKumar Muralidharan
2017-12-19 14:57 ` PrasannaKumar Muralidharan
2017-12-19 20:09 ` Alexandre Belloni
2017-12-21 13:36 ` PrasannaKumar Muralidharan
2017-12-08 15:46 ` [PATCH v2 10/13] MIPS: mscc: add ocelot dtsi Alexandre Belloni
2017-12-18 13:22 ` PrasannaKumar Muralidharan
2017-12-08 15:46 ` [PATCH v2 11/13] MIPS: mscc: add ocelot PCB123 device tree Alexandre Belloni
2017-12-18 13:29 ` PrasannaKumar Muralidharan
2017-12-08 15:46 ` [PATCH v2 12/13] MIPS: defconfigs: add a defconfig for Microsemi SoCs Alexandre Belloni
2017-12-08 15:46 ` [PATCH v2 13/13] MAINTAINERS: Add entry for Microsemi MIPS SoCs Alexandre Belloni
2017-12-17 16:59 ` [PATCH v2 00/13] MIPS: add support for the " PrasannaKumar Muralidharan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180109140705.GC2719@piout.net \
--to=alexandre.belloni@free-electrons.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mips@linux-mips.org \
--cc=ralf@linux-mips.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.