From: "Álvaro Fernández Rojas" <noltari@gmail.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 2/3] MIPS: add support for Broadcom MIPS BCM6368 SoC family
Date: Sat, 20 Jan 2018 11:53:58 +0100 [thread overview]
Message-ID: <20180120105359.17981-3-noltari@gmail.com> (raw)
In-Reply-To: <20180120105359.17981-1-noltari@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
---
arch/mips/dts/brcm,bcm6368.dtsi | 168 ++++++++++++++++++++++++++++++
arch/mips/mach-bmips/Kconfig | 24 +++++
include/configs/bmips_bcm6368.h | 30 ++++++
include/dt-bindings/clock/bcm6368-clock.h | 31 ++++++
include/dt-bindings/reset/bcm6368-reset.h | 22 ++++
5 files changed, 275 insertions(+)
create mode 100644 arch/mips/dts/brcm,bcm6368.dtsi
create mode 100644 include/configs/bmips_bcm6368.h
create mode 100644 include/dt-bindings/clock/bcm6368-clock.h
create mode 100644 include/dt-bindings/reset/bcm6368-reset.h
diff --git a/arch/mips/dts/brcm,bcm6368.dtsi b/arch/mips/dts/brcm,bcm6368.dtsi
new file mode 100644
index 0000000000..1bb538a1f3
--- /dev/null
+++ b/arch/mips/dts/brcm,bcm6368.dtsi
@@ -0,0 +1,168 @@
+/*
+ * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <dt-bindings/clock/bcm6368-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/reset/bcm6368-reset.h>
+#include "skeleton.dtsi"
+
+/ {
+ compatible = "brcm,bcm6368";
+
+ aliases {
+ spi0 = &spi;
+ };
+
+ cpus {
+ reg = <0x10000000 0x4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ u-boot,dm-pre-reloc;
+
+ cpu at 0 {
+ compatible = "brcm,bcm6368-cpu", "mips,mips4Kc";
+ device_type = "cpu";
+ reg = <0>;
+ u-boot,dm-pre-reloc;
+ };
+
+ cpu at 1 {
+ compatible = "brcm,bcm6368-cpu", "mips,mips4Kc";
+ device_type = "cpu";
+ reg = <1>;
+ u-boot,dm-pre-reloc;
+ };
+ };
+
+ clocks {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ u-boot,dm-pre-reloc;
+
+ periph_osc: periph-osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ u-boot,dm-pre-reloc;
+ };
+
+ periph_clk: periph-clk {
+ compatible = "brcm,bcm6345-clk";
+ reg = <0x10000004 0x4>;
+ #clock-cells = <1>;
+ };
+ };
+
+ pflash: nor at 18000000 {
+ compatible = "cfi-flash";
+ reg = <0x18000000 0x2000000>;
+ bank-width = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ status = "disabled";
+ };
+
+ ubus {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ u-boot,dm-pre-reloc;
+
+ pll_cntl: syscon at 10000008 {
+ compatible = "syscon";
+ reg = <0x10000008 0x4>;
+ };
+
+ syscon-reboot {
+ compatible = "syscon-reboot";
+ regmap = <&pll_cntl>;
+ offset = <0x0>;
+ mask = <0x1>;
+ };
+
+ periph_rst: reset-controller at 10000010 {
+ compatible = "brcm,bcm6345-reset";
+ reg = <0x10000010 0x4>;
+ #reset-cells = <1>;
+ };
+
+ wdt: watchdog at 1000005c {
+ compatible = "brcm,bcm6345-wdt";
+ reg = <0x1000005c 0xc>;
+ clocks = <&periph_osc>;
+ };
+
+ wdt-reboot {
+ compatible = "wdt-reboot";
+ wdt = <&wdt>;
+ };
+
+ gpio1: gpio-controller at 10000080 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x10000080 0x4>, <0x10000088 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ ngpios = <6>;
+
+ status = "disabled";
+ };
+
+ gpio0: gpio-controller at 10000084 {
+ compatible = "brcm,bcm6345-gpio";
+ reg = <0x10000084 0x4>, <0x1000008c 0x4>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ status = "disabled";
+ };
+
+ leds: led-controller at 100000d0 {
+ compatible = "brcm,bcm6358-leds";
+ reg = <0x100000d0 0x8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ status = "disabled";
+ };
+
+ uart0: serial at 10000100 {
+ compatible = "brcm,bcm6345-uart";
+ reg = <0x10000100 0x18>;
+ clocks = <&periph_osc>;
+
+ status = "disabled";
+ };
+
+ uart1: serial at 10000120 {
+ compatible = "brcm,bcm6345-uart";
+ reg = <0x10000120 0x18>;
+ clocks = <&periph_osc>;
+
+ status = "disabled";
+ };
+
+ spi: spi at 10000800 {
+ compatible = "brcm,bcm6358-spi";
+ reg = <0x10000800 0x70c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&periph_clk BCM6368_CLK_SPI>;
+ resets = <&periph_rst BCM6368_RST_SPI>;
+ spi-max-frequency = <20000000>;
+ num-cs = <6>;
+
+ status = "disabled";
+ };
+
+ memory-controller at 10001200 {
+ compatible = "brcm,bcm6358-mc";
+ reg = <0x10001200 0x4c>;
+ u-boot,dm-pre-reloc;
+ };
+ };
+};
diff --git a/arch/mips/mach-bmips/Kconfig b/arch/mips/mach-bmips/Kconfig
index db8b40523a..936b67f5f2 100644
--- a/arch/mips/mach-bmips/Kconfig
+++ b/arch/mips/mach-bmips/Kconfig
@@ -10,6 +10,7 @@ config SYS_SOC
default "bcm6338" if SOC_BMIPS_BCM6338
default "bcm6348" if SOC_BMIPS_BCM6348
default "bcm6358" if SOC_BMIPS_BCM6358
+ default "bcm6368" if SOC_BMIPS_BCM6368
default "bcm63268" if SOC_BMIPS_BCM63268
choice
@@ -70,6 +71,17 @@ config SOC_BMIPS_BCM6358
help
This supports BMIPS BCM6358 family including BCM6358 and BCM6359.
+config SOC_BMIPS_BCM6368
+ bool "BMIPS BCM6368 family"
+ select SUPPORTS_BIG_ENDIAN
+ select SUPPORTS_CPU_MIPS32_R1
+ select MIPS_TUNE_4KC
+ select MIPS_L1_CACHE_SHIFT_4
+ select SWAP_IO_SPACE
+ select SYSRESET_SYSCON
+ help
+ This supports BMIPS BCM6368 family including BCM6368 and BCM6369.
+
config SOC_BMIPS_BCM63268
bool "BMIPS BCM63268 family"
select SUPPORTS_BIG_ENDIAN
@@ -120,6 +132,17 @@ config BOARD_COMTREND_VR3032U
ethernet ports, 1 USB port, 1 UART, GPIO buttons and LEDs,
and a BCM6362 (integrated).
+config BOARD_COMTREND_WAP5813N
+ bool "Comtrend WAP-5813n board"
+ depends on SOC_BMIPS_BCM6368
+ select BMIPS_SUPPORTS_BOOT_RAM
+ help
+ Comtrend WAP-5813n boards have a BCM6369 SoC with 64 MB of RAM and
+ 8 MB of flash (CFI).
+ Between its different peripherals there's a BCM53115 switch with 5
+ ethernet ports, 1 USB port, 1 UART, GPIO buttons and LEDs,
+ and a BCM4322 (miniPCI).
+
config BOARD_HUAWEI_HG556A
bool "Huawei EchoLife HG556a"
depends on SOC_BMIPS_BCM6358
@@ -185,6 +208,7 @@ config BMIPS_SUPPORTS_BOOT_RAM
source "board/comtrend/ar5387un/Kconfig"
source "board/comtrend/ct5361/Kconfig"
source "board/comtrend/vr3032u/Kconfig"
+source "board/comtrend/wap5813n/Kconfig"
source "board/huawei/hg556a/Kconfig"
source "board/netgear/cg3100d/Kconfig"
source "board/sagem/f at st1704/Kconfig"
diff --git a/include/configs/bmips_bcm6368.h b/include/configs/bmips_bcm6368.h
new file mode 100644
index 0000000000..ce35fae6a0
--- /dev/null
+++ b/include/configs/bmips_bcm6368.h
@@ -0,0 +1,30 @@
+/*
+ * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_BMIPS_BCM6368_H
+#define __CONFIG_BMIPS_BCM6368_H
+
+/* CPU */
+#define CONFIG_SYS_MIPS_TIMER_FREQ 200000000
+
+/* RAM */
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_SYS_SDRAM_BASE 0x80000000
+
+/* U-Boot */
+#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + 0x100000
+
+#if defined(CONFIG_BMIPS_BOOT_RAM)
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#define CONFIG_SYS_INIT_SP_OFFSET 0x2000
+#endif
+
+#define CONFIG_SYS_FLASH_BASE 0xb8000000
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
+
+#endif /* __CONFIG_BMIPS_BCM6368_H */
diff --git a/include/dt-bindings/clock/bcm6368-clock.h b/include/dt-bindings/clock/bcm6368-clock.h
new file mode 100644
index 0000000000..9d41c0f131
--- /dev/null
+++ b/include/dt-bindings/clock/bcm6368-clock.h
@@ -0,0 +1,31 @@
+/*
+ * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
+ *
+ * Derived from linux/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_BCM6368_H
+#define __DT_BINDINGS_CLOCK_BCM6368_H
+
+#define BCM6368_CLK_VDSL_QPROC 2
+#define BCM6368_CLK_VDSL_AFE 3
+#define BCM6368_CLK_VDSL_BONDING 4
+#define BCM6368_CLK_VDSL 5
+#define BCM6368_CLK_PHYMIPS 6
+#define BCM6368_CLK_SWPKT_USB 7
+#define BCM6368_CLK_SWPKT_SAR 8
+#define BCM6368_CLK_SPI 9
+#define BCM6368_CLK_USBD 10
+#define BCM6368_CLK_SAR 11
+#define BCM6368_CLK_ROBOSW 12
+#define BCM6368_CLK_UTOPIA 13
+#define BCM6368_CLK_PCM 14
+#define BCM6368_CLK_USBH 15
+#define BCM6368_CLK_GLESS 16
+#define BCM6368_CLK_NAND 17
+#define BCM6368_CLK_IPSEC 18
+#define BCM6368_CLK_USBH_IDDQ 19
+
+#endif /* __DT_BINDINGS_CLOCK_BCM6368_H */
diff --git a/include/dt-bindings/reset/bcm6368-reset.h b/include/dt-bindings/reset/bcm6368-reset.h
new file mode 100644
index 0000000000..afa6a81d4c
--- /dev/null
+++ b/include/dt-bindings/reset/bcm6368-reset.h
@@ -0,0 +1,22 @@
+/*
+ * Copyright (C) 2017 Álvaro Fernández Rojas <noltari@gmail.com>
+ *
+ * Derived from linux/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DT_BINDINGS_RESET_BCM6368_H
+#define __DT_BINDINGS_RESET_BCM6368_H
+
+#define BCM6368_RST_SPI 0
+#define BCM6368_RST_MPI 3
+#define BCM6368_RST_IPSEC 4
+#define BCM6368_RST_EPHY 6
+#define BCM6368_RST_SAR 7
+#define BCM6368_RST_SWITCH 10
+#define BCM6368_RST_USBD 11
+#define BCM6368_RST_USBH 12
+#define BCM6368_RST_PCM 13
+
+#endif /* __DT_BINDINGS_RESET_BCM6368_H */
--
2.11.0
next prev parent reply other threads:[~2018-01-20 10:53 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-20 10:53 [U-Boot] [PATCH 0/3] mips: bmips: add BCM6368 SoC support Álvaro Fernández Rojas
2018-01-20 10:53 ` [U-Boot] [PATCH 1/3] dm: cpu: bmips: add BCM6368 support Álvaro Fernández Rojas
2018-01-20 10:53 ` Álvaro Fernández Rojas [this message]
2018-01-20 10:53 ` [U-Boot] [PATCH 3/3] MIPS: add BMIPS Comtrend WAP-5813n board Álvaro Fernández Rojas
2018-01-20 13:16 ` [U-Boot] [PATCH v2 0/3] mips: bmips: add BCM6368 SoC support Álvaro Fernández Rojas
2018-01-20 13:16 ` [U-Boot] [PATCH v2 1/3] dm: cpu: bmips: add BCM6368 support Álvaro Fernández Rojas
2018-01-21 16:46 ` Daniel Schwierzeck
2018-01-20 13:16 ` [U-Boot] [PATCH v2 2/3] MIPS: add support for Broadcom MIPS BCM6368 SoC family Álvaro Fernández Rojas
2018-01-21 16:46 ` Daniel Schwierzeck
2018-01-20 13:16 ` [U-Boot] [PATCH v2 3/3] MIPS: add BMIPS Comtrend WAP-5813n board Álvaro Fernández Rojas
2018-01-21 16:46 ` Daniel Schwierzeck
2018-01-26 12:18 ` [U-Boot] [PATCH 0/3] mips: bmips: add BCM6368 SoC support Daniel Schwierzeck
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180120105359.17981-3-noltari@gmail.com \
--to=noltari@gmail.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.