From: Jason Rush <jarush@gmail.com>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v6 4/4] dts: cadence_spi: Update documentation for DT bindings
Date: Tue, 23 Jan 2018 17:13:12 -0600 [thread overview]
Message-ID: <20180123231312.6231-5-jarush@gmail.com> (raw)
In-Reply-To: <20180123231312.6231-1-jarush@gmail.com>
Update documentation to reflect adopting the Linux DT bindings.
Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>
Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Marek Vasut <marex@denx.de>
---
Changes for v6:
- None
Changes for v5:
- Rebased
Changes for v4:
- Updated documentation
doc/device-tree-bindings/spi/spi-cadence.txt | 13 ++++++++-----
1 file changed, 8 insertions(+), 5 deletions(-)
diff --git a/doc/device-tree-bindings/spi/spi-cadence.txt b/doc/device-tree-bindings/spi/spi-cadence.txt
index c1e2233d7c..74c82080fc 100644
--- a/doc/device-tree-bindings/spi/spi-cadence.txt
+++ b/doc/device-tree-bindings/spi/spi-cadence.txt
@@ -6,7 +6,10 @@ Required properties:
- reg : 1.Physical base address and size of SPI registers map.
2. Physical base address & size of NOR Flash.
- clocks : Clock phandles (see clock bindings for details).
-- sram-size : spi controller sram size.
+- cdns,fifo-depth : Size of the data FIFO in words.
+- cdns,fifo-width : Bus width of the data FIFO in bytes.
+- cdns,trigger-address : 32-bit indirect AHB trigger address.
+- cdns,is-decoded-cs : Flag to indicate whether decoder is used or not.
- status : enable in requried dts.
connected flash properties
@@ -15,14 +18,14 @@ connected flash properties
- spi-max-frequency : Max supported spi frequency.
- page-size : Flash page size.
- block-size : Flash memory block size.
-- tshsl-ns : Added delay in master reference clocks (ref_clk) for
+- cdns,tshsl-ns : Added delay in master reference clocks (ref_clk) for
the length that the master mode chip select outputs
are de-asserted between transactions.
-- tsd2d-ns : Delay in master reference clocks (ref_clk) between one
+- cdns,tsd2d-ns : Delay in master reference clocks (ref_clk) between one
chip select being de-activated and the activation of
another.
-- tchsh-ns : Delay in master reference clocks between last bit of
+- cdns,tchsh-ns : Delay in master reference clocks between last bit of
current transaction and de-asserting the device chip
select (n_ss_out).
-- tslch-ns : Delay in master reference clocks between setting
+- cdns,tslch-ns : Delay in master reference clocks between setting
n_ss_out low and first bit transfer
--
2.11.0
next prev parent reply other threads:[~2018-01-23 23:13 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-23 23:13 [U-Boot] [PATCH v6 0/4] spi: cadence_spi: Adopt Linux DT bindings Jason Rush
2018-01-23 23:13 ` [U-Boot] [PATCH v6 1/4] spi: cadence_spi: Sync DT bindings with Linux Jason Rush
2018-01-23 23:13 ` [U-Boot] [PATCH v6 2/4] dts: " Jason Rush
2018-01-23 23:13 ` [U-Boot] [PATCH v6 3/4] config: cadence_spi: Remove defines read from DT Jason Rush
2018-01-23 23:13 ` Jason Rush [this message]
2018-01-25 14:17 ` [U-Boot] [PATCH v6 0/4] spi: cadence_spi: Adopt Linux DT bindings Jason Rush
2018-01-25 14:26 ` Jagan Teki
2018-01-26 5:59 ` Jagan Teki
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180123231312.6231-5-jarush@gmail.com \
--to=jarush@gmail.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.