From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Jeremy McNicoll <jeremymc@redhat.com>
Cc: linux-arm-msm@vger.kernel.org, linux-soc@vger.kernel.org,
devicetree@vger.kernel.org, linux-mmc@vger.kernel.org,
linux-clk@vger.kernel.org, andy.gross@linaro.org,
sboyd@codeaurora.org, robh@kernel.org, arnd@arndb.de,
riteshh@codeaurora.org, git@kchr.de, ulf.hansson@linaro.org,
jszhang@marvell.com
Subject: Re: [PATCH V4 5/6] dts: arm64: Enable onboard SDHCI on msm8992
Date: Wed, 28 Mar 2018 15:24:47 -0700 [thread overview]
Message-ID: <20180328222447.GC18510@minitux> (raw)
In-Reply-To: <1485508205-1904-6-git-send-email-jeremymc@redhat.com>
On Fri 27 Jan 01:10 PST 2017, Jeremy McNicoll wrote:
> This enables SDHCI on the Nexus 5X as well creates common smd_rpm node
> which can be shared between both 5X and 6P as per HW design.
>
> Given the lack of documentation, only downstream code was used as a reference
> and it eludes to the fact that 8994-rpm-regulator is common between both msm8992
> & msm8994. [ see msm.git branch: msm-angler-3.10-marshmallow-mr1, msm8992.dtsi]
>
> At this early stage of development it makes sense for the 8994-rpm-regulator
> to be common until data / documentation suggests otherwise.
>
Saw this as I looked through patchworks, still applies and compiles
cleanly.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Regards,
Bjorn
> Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
> ---
> .../boot/dts/qcom/msm8992-bullhead-rev-101.dts | 2 +
> arch/arm64/boot/dts/qcom/msm8992-pins.dtsi | 60 +++++
> arch/arm64/boot/dts/qcom/msm8992.dtsi | 87 ++++++-
> arch/arm64/boot/dts/qcom/msm8994-smd-rpm.dtsi | 276 +++++++++++++++++++++
> 4 files changed, 424 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/qcom/msm8994-smd-rpm.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
> index 4542133..3fc9a33 100644
> --- a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
> +++ b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
> @@ -39,3 +39,5 @@
> };
> };
> };
> +
> +#include "msm8994-smd-rpm.dtsi"
> diff --git a/arch/arm64/boot/dts/qcom/msm8992-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8992-pins.dtsi
> index d2a26f0..31bc9d9 100644
> --- a/arch/arm64/boot/dts/qcom/msm8992-pins.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8992-pins.dtsi
> @@ -35,4 +35,64 @@
> bias-pull-down;
> };
> };
> +
> + /* 0-3 for sdc1 4-6 for sdc2 */
> + /* Order of pins */
> + /* SDC1: CLK -> 0, CMD -> 1, DATA -> 2, RCLK -> 3 */
> + /* SDC2: CLK -> 4, CMD -> 5, DATA -> 6 */
> + sdc1_clk_on: clk-on {
> + pinconf {
> + pins = "sdc1_clk";
> + bias-disable = <0>; /* No pull */
> + drive-strength = <16>; /* 16mA */
> + };
> + };
> +
> + sdc1_clk_off: clk-off {
> + pinconf {
> + pins = "sdc1_clk";
> + bias-disable = <0>; /* No pull */
> + drive-strength = <2>; /* 2mA */
> + };
> + };
> +
> + sdc1_cmd_on: cmd-on {
> + pinconf {
> + pins = "sdc1_cmd";
> + bias-pull-up;
> + drive-strength = <8>;
> + };
> + };
> +
> + sdc1_cmd_off: cmd-off {
> + pinconf {
> + pins = "sdc1_cmd";
> + bias-pull-up = <0x3>; /* same as 3.10 ?? */
> + drive-strength = <2>; /* 2mA */
> + };
> + };
> +
> + sdc1_data_on: data-on {
> + pinconf {
> + pins = "sdc1_data";
> + bias-pull-up;
> + drive-strength = <8>; /* 8mA */
> + };
> + };
> +
> + sdc1_data_off: data-off {
> + pinconf {
> + pins = "sdc1_data";
> + bias-pull-up;
> + drive-strength = <2>;
> + };
> + };
> +
> + sdc1_rclk_on: rclk-on {
> + bias-pull-down; /* pull down */
> + };
> +
> + sdc1_rclk_off: rclk-off {
> + bias-pull-down; /* pull down */
> + };
> };
> diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi
> index 2c05ec7..623c850 100644
> --- a/arch/arm64/boot/dts/qcom/msm8992.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi
> @@ -189,6 +189,31 @@
> reg = <0xfc400000 0x2000>;
> };
>
> + sdhci1: mmc@f9824900 {
> + compatible = "qcom,sdhci-msm-v4";
> + reg = <0xf9824900 0x1a0>, <0xf9824000 0x800>;
> + reg-names = "hc_mem", "core_mem";
> +
> + interrupts = <GIC_SPI 123 IRQ_TYPE_NONE>,
> + <GIC_SPI 138 IRQ_TYPE_NONE>;
> + interrupt-names = "hc_irq", "pwr_irq";
> +
> + clocks = <&clock_gcc GCC_SDCC1_APPS_CLK>,
> + <&clock_gcc GCC_SDCC1_AHB_CLK>;
> + clock-names = "core", "iface";
> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on
> + &sdc1_rclk_on>;
> + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off
> + &sdc1_rclk_off>;
> +
> + regulator-always-on;
> + bus-width = <8>;
> + mmc-hs400-1_8v;
> + status = "okay";
> + };
> +
> rpm_msg_ram: memory@fc428000 {
> compatible = "qcom,rpm-msg-ram";
> reg = <0xfc428000 0x4000>;
> @@ -231,7 +256,67 @@
> };
> };
>
> + smd_rpm: smd {
> + compatible = "qcom,smd";
> + rpm {
> + interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
> + qcom,ipc = <&apcs 8 0>;
> + qcom,smd-edge = <15>;
> + qcom,local-pid = <0>;
> + qcom,remote-pid = <6>;
> +
> + rpm-requests {
> + compatible = "qcom,rpm-msm8994";
> + qcom,smd-channels = "rpm_requests";
> +
> + pm8994-regulators {
> + compatible = "qcom,rpm-pm8994-regulators";
> +
> + pm8994_s1: s1 {};
> + pm8994_s2: s2 {};
> + pm8994_s3: s3 {};
> + pm8994_s4: s4 {};
> + pm8994_s5: s5 {};
> + pm8994_s6: s6 {};
> + pm8994_s7: s7 {};
> +
> + pm8994_l1: l1 {};
> + pm8994_l2: l2 {};
> + pm8994_l3: l3 {};
> + pm8994_l4: l4 {};
> + pm8994_l6: l6 {};
> + pm8994_l8: l8 {};
> + pm8994_l9: l9 {};
> + pm8994_l10: l10 {};
> + pm8994_l11: l11 {};
> + pm8994_l12: l12 {};
> + pm8994_l13: l13 {};
> + pm8994_l14: l14 {};
> + pm8994_l15: l15 {};
> + pm8994_l16: l16 {};
> + pm8994_l17: l17 {};
> + pm8994_l18: l18 {};
> + pm8994_l19: l19 {};
> + pm8994_l20: l20 {};
> + pm8994_l21: l21 {};
> + pm8994_l22: l22 {};
> + pm8994_l23: l23 {};
> + pm8994_l24: l24 {};
> + pm8994_l25: l25 {};
> + pm8994_l26: l26 {};
> + pm8994_l27: l27 {};
> + pm8994_l28: l28 {};
> + pm8994_l29: l29 {};
> + pm8994_l30: l30 {};
> + pm8994_l31: l31 {};
> + pm8994_l32: l32 {};
> +
> + pm8994_lvs1: lvs1 {};
> + pm8994_lvs2: lvs2 {};
> + };
> + };
> + };
> + };
> };
>
> -
> #include "msm8992-pins.dtsi"
> diff --git a/arch/arm64/boot/dts/qcom/msm8994-smd-rpm.dtsi b/arch/arm64/boot/dts/qcom/msm8994-smd-rpm.dtsi
> new file mode 100644
> index 0000000..47ebd16
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8994-smd-rpm.dtsi
> @@ -0,0 +1,276 @@
> +/* Copyright (c) 2015, LGE Inc. All rights reserved.
> + * Copyright (c) 2016, The Linux Foundation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 and
> + * only version 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +&smd_rpm {
> + rpm {
> + rpm_requests {
> + pm8994-regulators {
> +
> + vdd_l1-supply = <&pm8994_s1>;
> + vdd_l2_26_28-supply = <&pm8994_s3>;
> + vdd_l3_11-supply = <&pm8994_s3>;
> + vdd_l4_27_31-supply = <&pm8994_s3>;
> + vdd_l5_7-supply = <&pm8994_s3>;
> + vdd_l6_12_32-supply = <&pm8994_s5>;
> + vdd_l8_16_30-supply = <&vreg_vph_pwr>;
> + vdd_l9_10_18_22-supply = <&vreg_vph_pwr>;
> + vdd_l13_19_23_24-supply = <&vreg_vph_pwr>;
> + vdd_l14_15-supply = <&pm8994_s5>;
> + vdd_l17_29-supply = <&vreg_vph_pwr>;
> + vdd_l20_21-supply = <&vreg_vph_pwr>;
> + vdd_l25-supply = <&pm8994_s5>;
> + vdd_lvs1_2 = <&pm8994_s4>;
> +
> + s1 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <800000>;
> + };
> +
> + s2 {
> + /* TODO */
> + };
> +
> + s3 {
> + regulator-min-microvolt = <1300000>;
> + regulator-max-microvolt = <1300000>;
> + };
> +
> + s4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-allow-set-load;
> + regulator-system-load = <325000>;
> + };
> +
> + s5 {
> + regulator-min-microvolt = <2150000>;
> + regulator-max-microvolt = <2150000>;
> + };
> +
> + s7 {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + };
> +
> + l1 {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + };
> +
> + l2 {
> + regulator-min-microvolt = <1250000>;
> + regulator-max-microvolt = <1250000>;
> + };
> +
> + l3 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + };
> +
> + l4 {
> + regulator-min-microvolt = <1225000>;
> + regulator-max-microvolt = <1225000>;
> + };
> +
> + l5 {
> + /* TODO */
> + };
> +
> + l6 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + l7 {
> + /* TODO */
> + };
> +
> + l8 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + l9 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + };
> +
> + l10 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + qcom,init-voltage = <1800000>;
> + };
> +
> + l11 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + qcom,init-voltage = <1200000>;
> + };
> +
> + l12 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + qcom,init-voltage = <1800000>;
> + proxy-supply = <&pm8994_l12>;
> + qcom,proxy-consumer-enable;
> + qcom,proxy-consumer-current = <10000>;
> + status = "okay";
> + };
> +
> + l13 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2950000>;
> + qcom,init-voltage = <2950000>;
> + status = "okay";
> + };
> +
> + l14 {
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + qcom,init-voltage = <1200000>;
> + proxy-supply = <&pm8994_l14>;
> + qcom,proxy-consumer-enable;
> + qcom,proxy-consumer-current = <10000>;
> + status = "okay";
> + };
> +
> + l15 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + qcom,init-voltage = <1800000>;
> + status = "okay";
> + };
> +
> + l16 {
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <2700000>;
> + qcom,init-voltage = <2700000>;
> + status = "okay";
> + };
> +
> + l17 {
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <2700000>;
> + qcom,init-voltage = <2700000>;
> + status = "okay";
> + };
> +
> + l18 {
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> + qcom,init-voltage = <3000000>;
> + qcom,init-ldo-mode = <1>;
> + };
> +
> + l19 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + qcom,init-voltage = <1800000>;
> + status = "okay";
> + };
> +
> + l20 {
> + regulator-min-microvolt = <2950000>;
> + regulator-max-microvolt = <2950000>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-allow-set-load;
> + regulator-system-load = <570000>;
> + };
> +
> + l21 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + qcom,init-voltage = <1800000>;
> + };
> +
> + l22 {
> + regulator-min-microvolt = <3100000>;
> + regulator-max-microvolt = <3100000>;
> + qcom,init-voltage = <3100000>;
> + };
> +
> + l23 {
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + qcom,init-voltage = <2800000>;
> + };
> +
> + l24 {
> + regulator-min-microvolt = <3075000>;
> + regulator-max-microvolt = <3150000>;
> + qcom,init-voltage = <3075000>;
> + };
> +
> + l25 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + qcom,init-voltage = <1800000>;
> + };
> +
> + l26 {
> + /* TODO: value from downstream
> + regulator-min-microvolt = <987500>;
> + fails to apply */
> + };
> +
> + l27 {
> + regulator-min-microvolt = <1050000>;
> + regulator-max-microvolt = <1050000>;
> + qcom,init-voltage = <1050000>;
> + };
> +
> + l28 {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + qcom,init-voltage = <1000000>;
> + proxy-supply = <&pm8994_l28>;
> + qcom,proxy-consumer-enable;
> + qcom,proxy-consumer-current = <10000>;
> + };
> +
> + l29 {
> + /* TODO: Unsupported voltage range.
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + qcom,init-voltage = <2800000>;
> + */
> + };
> +
> + l30 {
> + /* TODO: get this verified
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + qcom,init-voltage = <1800000>;
> + */
> + };
> +
> + l31 {
> + regulator-min-microvolt = <1262500>;
> + regulator-max-microvolt = <1262500>;
> + qcom,init-voltage = <1262500>;
> + };
> +
> + l32 {
> + /* TODO: get this verified
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + qcom,init-voltage = <1800000>;
> + */
> + };
> + };
> + };
> + };
> +};
> --
> 2.6.1
>
next prev parent reply other threads:[~2018-03-28 22:24 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-27 9:09 [PATCH V4 0/6] Enable onboard SDHCI for Nexus 5X (msm8992) Jeremy McNicoll
2017-01-27 9:10 ` [PATCH V4 1/6] clk: qcom: SDHCI enablement on Nexus 5X / 6P Jeremy McNicoll
2017-01-27 17:00 ` kbuild test robot
2017-01-27 17:00 ` kbuild test robot
2017-01-27 21:33 ` Stephen Boyd
[not found] ` <1485508205-1904-1-git-send-email-jeremymc-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
2017-01-27 9:10 ` [PATCH V4 2/6] dt-bindings: qcom: clk: Add missing binding for SDCHI enablement on Nexus 5X/6P Jeremy McNicoll
2017-01-27 9:10 ` Jeremy McNicoll
2017-01-27 21:33 ` Stephen Boyd
2017-01-27 9:10 ` [PATCH V4 3/6] arm64: dts: msm8992 add fixed regulator Jeremy McNicoll
2017-01-27 9:10 ` [PATCH V4 4/6] arm64: dts: smem enablement for msm8992 Jeremy McNicoll
2017-01-27 19:58 ` Stephen Boyd
2017-01-30 5:44 ` Jeremy McNicoll
2018-03-14 2:52 ` Bjorn Andersson
2017-01-27 9:10 ` [PATCH V4 5/6] dts: arm64: Enable onboard SDHCI on msm8992 Jeremy McNicoll
2018-03-28 22:24 ` Bjorn Andersson [this message]
2017-01-27 9:10 ` [PATCH V4 6/6] dts: doc: rename rpm_requests to respect DT naming conventions Jeremy McNicoll
2017-02-01 14:06 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180328222447.GC18510@minitux \
--to=bjorn.andersson@linaro.org \
--cc=andy.gross@linaro.org \
--cc=arnd@arndb.de \
--cc=devicetree@vger.kernel.org \
--cc=git@kchr.de \
--cc=jeremymc@redhat.com \
--cc=jszhang@marvell.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=riteshh@codeaurora.org \
--cc=robh@kernel.org \
--cc=sboyd@codeaurora.org \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.