From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
To: mturquette@baylibre.com, sboyd@kernel.org, robh+dt@kernel.org,
mark.rutland@arm.com, lee.jones@linaro.org, lgirdwood@gmail.com,
broonie@kernel.org, mazziesaccount@gmail.com
Cc: linux-clk@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, mikko.mutanen@fi.rohmeurope.com,
heikki.haikola@fi.rohmeurope.com
Subject: [PATCH v2 3/6] regulator: bd71837: Devicetree bindings for BD71837 regulators
Date: Mon, 28 May 2018 12:01:01 +0300 [thread overview]
Message-ID: <20180528090101.GD8778@localhost.localdomain> (raw)
Document devicetree bindings for ROHM BD71837 PMIC regulators.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
.../bindings/regulator/rohm,bd71837-regulator.txt | 126 +++++++++++++++++++++
1 file changed, 126 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
new file mode 100644
index 000000000000..4edf3137d9f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.txt
@@ -0,0 +1,126 @@
+ROHM BD71837 Power Management Integrated Circuit (PMIC) regulator bindings
+
+BD71837MWV is a programmable Power Management
+IC (PMIC) for powering single-core, dual-core, and
+quad-core SoC’s such as NXP-i.MX 8M. It is optimized
+for low BOM cost and compact solution footprint. It
+integrates 8 Buck regulators and 7 LDO’s to provide all
+the power rails required by the SoC and the commonly
+used peripherals.
+
+Required properties:
+ - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7"
+
+List of regulators provided by this controller. BD71837 regulators node
+should be sub node of the BD71837 MFD node. See BD71837 MFD bindings at
+Documentation/devicetree/bindings/mfd/rohm,bd71837-pmic.txt
+Regulator nodes should be named to BUCK_<number> and LDO_<number>. The
+definition for each of these nodes is defined using the standard
+binding for regulators at
+Documentation/devicetree/bindings/regulator/regulator.txt.
+Note that if BD71837 starts at RUN state you probably want to use
+regulator-boot-on at least for BUCK6 and BUCK7 so that those are not
+disabled by driver at startup. LDO5 and LDO6 are supplied by those and
+if they are disabled at startup the voltage monitoring for LDO5/LDO6 will
+cause PMIC to reset.
+
+The valid names for regulator nodes are:
+BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7, BUCK8
+LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7
+
+Optional properties:
+- Any optional property defined in bindings/regulator/regulator.txt
+
+Example:
+regulators {
+ buck1: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <1250>;
+ };
+ buck2: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ };
+ buck3: BUCK3 {
+ regulator-name = "buck3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ };
+ buck4: BUCK4 {
+ regulator-name = "buck4";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ };
+ buck5: BUCK5 {
+ regulator-name = "buck5";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ };
+ buck6: BUCK6 {
+ regulator-name = "buck6";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ buck7: BUCK7 {
+ regulator-name = "buck7";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ };
+ buck8: BUCK8 {
+ regulator-name = "buck8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ };
+
+ ldo1: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ ldo2: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ };
+ ldo3: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ ldo4: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ ldo5: LDO5 {
+ regulator-name = "ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ ldo6: LDO6 {
+ regulator-name = "ldo6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ ldo7_reg: LDO7 {
+ regulator-name = "ldo7";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+
--
2.14.3
next reply other threads:[~2018-05-28 9:01 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-28 9:01 Matti Vaittinen [this message]
2018-05-30 11:02 ` Applied "regulator: bd71837: Devicetree bindings for BD71837 regulators" to the regulator tree Mark Brown
2018-05-30 11:02 ` Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180528090101.GD8778@localhost.localdomain \
--to=matti.vaittinen@fi.rohmeurope.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=heikki.haikola@fi.rohmeurope.com \
--cc=lee.jones@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mazziesaccount@gmail.com \
--cc=mikko.mutanen@fi.rohmeurope.com \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.