All of lore.kernel.org
 help / color / mirror / Atom feed
From: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
To: Marek Vasut <marek.vasut@gmail.com>
Cc: linux-pci@vger.kernel.org,
	Marek Vasut <marek.vasut+renesas@gmail.com>,
	Geert Uytterhoeven <geert+renesas@glider.be>,
	Phil Edworthy <phil.edworthy@renesas.com>,
	Simon Horman <horms+renesas@verge.net.au>,
	Wolfram Sang <wsa@the-dreams.de>,
	linux-renesas-soc@vger.kernel.org
Subject: Re: [PATCH v4 6/6] PCI: rcar: Shut the PHY down in failpath
Date: Fri, 29 Jun 2018 14:38:05 +0100	[thread overview]
Message-ID: <20180629133805.GA9643@red-moon> (raw)
In-Reply-To: <20180524143624.26718-7-marek.vasut+renesas@gmail.com>

On Thu, May 24, 2018 at 04:36:24PM +0200, Marek Vasut wrote:
> If anything fails past phy_init_fn() and the system is a Gen3 with
> a PHY, the PHY will be left on and inited. This is caused by the
> phy_init_fn, which is in fact a pointer to rcar_pcie_phy_init_gen3()
> function, which starts the PHY, yet has no counterpart in the failpath.
> Add that counterpart.
> 
> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
> Cc: Geert Uytterhoeven <geert+renesas@glider.be>
> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
> Cc: Phil Edworthy <phil.edworthy@renesas.com>
> Cc: Simon Horman <horms+renesas@verge.net.au>
> Cc: Wolfram Sang <wsa@the-dreams.de>
> Cc: linux-renesas-soc@vger.kernel.org
> Fixes: 517ca93a7159 ("PCI: rcar: Add R-Car gen3 PHY support")
> ---
> V4: New patch
> ---
>  drivers/pci/host/pcie-rcar.c | 10 ++++++++--
>  1 file changed, 8 insertions(+), 2 deletions(-)

Applied to pci/controller-fixes to be tentatively merged at -rc4,
thanks.

Lorenzo

> diff --git a/drivers/pci/host/pcie-rcar.c b/drivers/pci/host/pcie-rcar.c
> index 636c3c5095d2..695781934f0a 100644
> --- a/drivers/pci/host/pcie-rcar.c
> +++ b/drivers/pci/host/pcie-rcar.c
> @@ -1163,7 +1163,7 @@ static int rcar_pcie_probe(struct platform_device *pdev)
>  	if (rcar_pcie_hw_init(pcie)) {
>  		dev_info(dev, "PCIe link down\n");
>  		err = -ENODEV;
> -		goto err_clk_disable;
> +		goto err_phy_shutdown;
>  	}
>  
>  	data = rcar_pci_read_reg(pcie, MACSR);
> @@ -1175,7 +1175,7 @@ static int rcar_pcie_probe(struct platform_device *pdev)
>  			dev_err(dev,
>  				"failed to enable MSI support: %d\n",
>  				err);
> -			goto err_clk_disable;
> +			goto err_phy_shutdown;
>  		}
>  	}
>  
> @@ -1189,6 +1189,12 @@ static int rcar_pcie_probe(struct platform_device *pdev)
>  	if (IS_ENABLED(CONFIG_PCI_MSI))
>  		rcar_pcie_teardown_msi(pcie);
>  
> +err_phy_shutdown:
> +	if (pcie->phy) {
> +		phy_power_off(pcie->phy);
> +		phy_exit(pcie->phy);
> +	}
> +
>  err_clk_disable:
>  	clk_disable_unprepare(pcie->bus_clk);
>  
> -- 
> 2.16.2
> 

  parent reply	other threads:[~2018-06-29 13:36 UTC|newest]

Thread overview: 24+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-05-24 14:36 [PATCH v4 0/6] PCI: rcar: Failpath fixes Marek Vasut
2018-05-24 14:36 ` [PATCH v4 1/6] PCI: rcar: Pull bus clock enable/disable from rcar_pcie_get_resources() Marek Vasut
2018-05-28  8:51   ` Simon Horman
2018-05-24 14:36 ` [PATCH v4 2/6] PCI: rcar: Add missing irq_dispose_mapping() into failpath Marek Vasut
2018-05-28  8:51   ` Simon Horman
2018-05-24 14:36 ` [PATCH v4 3/6] PCI: rcar: Teardown MSI setup if rcar_pcie_enable() fails Marek Vasut
2018-05-28  8:52   ` Simon Horman
2018-05-24 14:36 ` [PATCH v4 4/6] PCI: rcar: Poll more often in rcar_pcie_wait_for_dl() Marek Vasut
2018-05-28  8:53   ` Simon Horman
2018-05-24 14:36 ` [PATCH v4 5/6] PCI: rcar: Remove IRQ mappings in rcar_pcie_enable_msi failpath Marek Vasut
2018-05-28  8:53   ` Simon Horman
2018-05-24 14:36 ` [PATCH v4 6/6] PCI: rcar: Shut the PHY down in failpath Marek Vasut
2018-05-25 10:09   ` Geert Uytterhoeven
2018-05-25 18:34     ` Marek Vasut
2018-05-28  8:48   ` Simon Horman
2018-06-01 23:30     ` Marek Vasut
2018-06-29 13:38   ` Lorenzo Pieralisi [this message]
2018-05-25  9:35 ` [PATCH v4 0/6] PCI: rcar: Failpath fixes Lorenzo Pieralisi
2018-05-25  9:39   ` Geert Uytterhoeven
2018-05-25  9:56     ` Lorenzo Pieralisi
2018-05-25 10:01       ` Geert Uytterhoeven
2018-05-25 16:43 ` Lorenzo Pieralisi
2018-05-25 17:10   ` Marek Vasut
2018-05-28  8:54   ` Simon Horman

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180629133805.GA9643@red-moon \
    --to=lorenzo.pieralisi@arm.com \
    --cc=geert+renesas@glider.be \
    --cc=horms+renesas@verge.net.au \
    --cc=linux-pci@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=marek.vasut+renesas@gmail.com \
    --cc=marek.vasut@gmail.com \
    --cc=phil.edworthy@renesas.com \
    --cc=wsa@the-dreams.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.