Re: [PATCH 2/8] mmc: tegra: Parse and program DQS trim value

[Thierry Reding <thierry.reding@gmail.com>]

[-- Attachment #1: Type: text/plain, Size: 3233 bytes --]

On Tue, Aug 07, 2018 at 04:59:58PM +0300, Aapo Vienamo wrote:
> Parse and program the HS400 DQS trim value from dt. Program a fallback
> value in case the property is missing.
> 
> Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
> ---
>  drivers/mmc/host/sdhci-tegra.c | 32 +++++++++++++++++++++++++++++---
>  1 file changed, 29 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
> index 7f1ac4a..426f7ea 100644
> --- a/drivers/mmc/host/sdhci-tegra.c
> +++ b/drivers/mmc/host/sdhci-tegra.c
> @@ -43,6 +43,10 @@
>  #define SDHCI_CLOCK_CTRL_PADPIPE_CLKEN_OVERRIDE		BIT(3)
>  #define SDHCI_CLOCK_CTRL_SPI_MODE_CLKEN_OVERRIDE	BIT(2)
>  
> +#define SDHCI_TEGRA_VENDOR_CAP_OVERRIDES		0x10c
> +#define SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_MASK		0x00003f00
> +#define SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_SHIFT	8
> +
>  #define SDHCI_TEGRA_VENDOR_MISC_CTRL			0x120
>  #define SDHCI_MISC_CTRL_ENABLE_SDR104			0x8
>  #define SDHCI_MISC_CTRL_ENABLE_SDR50			0x10
> @@ -112,6 +116,7 @@ struct sdhci_tegra {
>  
>  	u32 default_tap;
>  	u32 default_trim;
> +	u32 dqs_trim;
>  };
>  
>  static u16 tegra_sdhci_readw(struct sdhci_host *host, int reg)
> @@ -500,7 +505,7 @@ static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
>  		autocal->pull_down_hs400 = autocal->pull_down_1v8;
>  }
>  
> -static void tegra_sdhci_parse_default_tap_and_trim(struct sdhci_host *host)
> +static void tegra_sdhci_parse_tap_and_trim(struct sdhci_host *host)
>  {
>  	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>  	struct sdhci_tegra *tegra_host = sdhci_pltfm_priv(pltfm_host);
> @@ -515,6 +520,11 @@ static void tegra_sdhci_parse_default_tap_and_trim(struct sdhci_host *host)
>  				       &tegra_host->default_trim);
>  	if (err)
>  		tegra_host->default_trim = 0;
> +
> +	err = device_property_read_u32(host->mmc->parent, "nvidia,dqs-trim",
> +				       &tegra_host->dqs_trim);
> +	if (err)
> +		tegra_host->dqs_trim = 0x11;

Okay, so there's only one value. I think that should be clarified in the
bindings documentation. It should mention that a single cell is used for
this. Also, I assume there are lower and upper limits for the valid
range of DQS trim values. Might make sense to specify those in the DT
bindings as well.

>  }
>  
>  static void tegra_sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
> @@ -545,20 +555,33 @@ static unsigned int tegra_sdhci_get_max_clock(struct sdhci_host *host)
>  	return clk_round_rate(pltfm_host->clk, UINT_MAX);
>  }
>  
> +static void tegra_sdhci_set_dqs_trim(struct sdhci_host *host, u8 val)
> +{
> +	u32 reg;
> +
> +	reg = sdhci_readl(host, SDHCI_TEGRA_VENDOR_CAP_OVERRIDES);
> +	reg &= ~SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_MASK;
> +	reg |= val<<SDHCI_TEGRA_CAP_OVERRIDES_DQS_TRIM_SHIFT;
> +	sdhci_writel(host, reg, SDHCI_TEGRA_VENDOR_CAP_OVERRIDES);
> +}

Nit: I dislike using "reg" as a variable representing a register value
because I keep interpreting it as designating a register offset. Hence
I tend to use more explicit "offset" for actual register offsets and
"value" for register values.

But maybe that's just me.

Thierry

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]