From: Lina Iyer <ilina@codeaurora.org>
To: Raju P L S S S N <rplsssn@codeaurora.org>
Cc: andy.gross@linaro.org, david.brown@linaro.org,
linux-arm-msm@vger.kernel.org, linux-soc@vger.kernel.org,
rnayak@codeaurora.org, bjorn.andersson@linaro.org,
linux-kernel@vger.kernel.org, sboyd@kernel.org,
evgreen@chromium.org, dianders@chromium.org, mka@chromium.org
Subject: Re: [PATCH v2 0/6] drivers/qcom: add additional functionality to RPMH
Date: Wed, 5 Sep 2018 14:05:57 -0600 [thread overview]
Message-ID: <20180905200557.GC28215@codeaurora.org> (raw)
In-Reply-To: <1532685889-31345-1-git-send-email-rplsssn@codeaurora.org>
Stephen, Doug,
Would you have some time to take a look at this series?
Thanks,
Lina
On Fri, Jul 27 2018 at 04:04 -0600, Raju P L S S S N wrote:
>From: "Raju P.L.S.S.S.N" <rplsssn@codeaurora.org>
>
>Changes in v1:
>- Remove unnecessary EXPORT_SYMBOL in rpmh-rsc
>
>This set of patches add additional functionality to RPMH drivers[1].
>
>PM drivers can choose to disallow idle modes when RSC controller is busy
>sending or processing requests. The patches add necessary functions to
>query the controller status.
>
>The controllers may be in 'solver' state, where they could be in autonomous
>mode executing low power modes for their hardware and as such are not
>available for sending active votes. Functionality to get notified about
>such state and disallow requests for state change in that case is added
>in these patches.
>
>The Power Domain Controller can be programmed to wakeup the RSC and
>setup the resources back in the active state, before the processor is
>woken up by a timer interrupt. The wakeup value from the timer hardware
>can be copied to the PDC which has its own timer and is in an always-on
>power domain. Programming the wakeup value is done through a separate
>register on the RSC. Functions necessary to program wakeup is added in
>the patches.
>
>Please consider reviewing this patchset.
>
>v1:https://lkml.org/lkml/2018/7/19/213
>
>
>
>[1] https://lkml.org/lkml/2018/6/20/519
>
>Lina Iyer (5):
> drivers: qcom: rpmh-rsc: return if the controller is idle
> drivers: qcom: rpmh: export controller idle status
> drivers: qcom: rpmh: disallow active requests in solver mode
> drivers: qcom: rpmh-rsc: write PDC data
> drivers: qcom: rpmh: write PDC data
>
>Raju P.L.S.S.S.N (1):
> drivers: qcom: rpmh-rsc: clear active mode configuration for waketcs
>
> drivers/soc/qcom/rpmh-internal.h | 6 ++
> drivers/soc/qcom/rpmh-rsc.c | 132 ++++++++++++++++++++++++++++++---------
> drivers/soc/qcom/rpmh.c | 100 +++++++++++++++++++++++++++++
> include/soc/qcom/rpmh.h | 16 +++++
> 4 files changed, 225 insertions(+), 29 deletions(-)
>
>--
>The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,\na Linux Foundation Collaborative Project
>
prev parent reply other threads:[~2018-09-05 20:05 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-07-27 10:04 [PATCH v2 0/6] drivers/qcom: add additional functionality to RPMH Raju P L S S S N
2018-07-27 10:04 ` [PATCH v2 1/6] drivers: qcom: rpmh-rsc: return if the controller is idle Raju P L S S S N
2018-09-11 22:39 ` Matthias Kaehlcke
2018-09-12 2:20 ` Lina Iyer
2018-07-27 10:04 ` [PATCH v2 2/6] drivers: qcom: rpmh: export controller idle status Raju P L S S S N
2018-07-27 10:04 ` [PATCH v2 3/6] drivers: qcom: rpmh: disallow active requests in solver mode Raju P L S S S N
2018-09-11 23:02 ` Matthias Kaehlcke
2018-09-12 2:22 ` Lina Iyer
2018-07-27 10:04 ` [PATCH v2 4/6] drivers: qcom: rpmh-rsc: clear active mode configuration for waketcs Raju P L S S S N
2018-09-12 21:51 ` Matthias Kaehlcke
2018-07-27 10:04 ` [PATCH v2 5/6] drivers: qcom: rpmh-rsc: write PDC data Raju P L S S S N
2018-09-12 22:28 ` Matthias Kaehlcke
2018-09-12 22:33 ` Lina Iyer
2018-09-12 22:37 ` Matthias Kaehlcke
2018-07-27 10:04 ` [PATCH v2 6/6] drivers: qcom: rpmh: " Raju P L S S S N
2018-09-12 22:55 ` Matthias Kaehlcke
2018-09-05 20:05 ` Lina Iyer [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180905200557.GC28215@codeaurora.org \
--to=ilina@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=bjorn.andersson@linaro.org \
--cc=david.brown@linaro.org \
--cc=dianders@chromium.org \
--cc=evgreen@chromium.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=mka@chromium.org \
--cc=rnayak@codeaurora.org \
--cc=rplsssn@codeaurora.org \
--cc=sboyd@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.