From: Stanislaw Gruszka <sgruszka@redhat.com>
To: Tom Psyborg <pozega.tomislav@gmail.com>
Cc: Daniel Golle <daniel@makrotopia.org>,
linux-wireless@vger.kernel.org, Mathias Kresin <dev@kresin.me>,
Felix Fietkau <nbd@nbd.name>
Subject: Re: [PATCH v3 4/4] rt2800: fix registers init for MT7620
Date: Thu, 11 Oct 2018 12:05:25 +0200 [thread overview]
Message-ID: <20181011100524.GA20794@redhat.com> (raw)
In-Reply-To: <CAKR_QVLjFyGtzikLTiQKhrVBSyUoPmDn2tMJqto8dyBDjoFJOQ@mail.gmail.com>
On Wed, Oct 10, 2018 at 10:03:12PM +0200, Tom Psyborg wrote:
> ok, that is strange. do you see any performance differences without
> TX_SW_CFG regs? iperf test is a good pointer.
>
> this was a problem on xiaomi mini with old DD trunk builds on 4.4
> kernel and LEDE builds from last year. i ain't got no chance to try
> this on 18.06. which device you tried this on? if ipa/ilna it might
> make no difference
No diffrence for me. I have nexx wt3020 8M.
However I notice this set couse performance regression for me.
When connecting to iwl 7265 . Without the set I have:
root@LEDE:~# iperf3 -c 192.168.10.243
Connecting to host 192.168.10.243, port 5201
[ 5] local 192.168.10.1 port 59304 connected to 192.168.10.243 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 5.37 MBytes 44.9 Mbits/sec 0 279 KBytes
[ 5] 1.00-2.00 sec 5.80 MBytes 48.8 Mbits/sec 0 494 KBytes
[ 5] 2.00-3.00 sec 6.03 MBytes 50.5 Mbits/sec 0 513 KBytes
[ 5] 3.00-4.01 sec 5.90 MBytes 49.2 Mbits/sec 0 513 KBytes
[ 5] 4.01-5.01 sec 5.90 MBytes 49.5 Mbits/sec 0 515 KBytes
[ 5] 5.01-6.00 sec 5.78 MBytes 48.9 Mbits/sec 0 515 KBytes
[ 5] 6.00-7.00 sec 5.66 MBytes 47.4 Mbits/sec 0 515 KBytes
[ 5] 7.00-8.00 sec 6.03 MBytes 50.6 Mbits/sec 0 515 KBytes
[ 5] 8.00-9.00 sec 6.09 MBytes 50.9 Mbits/sec 0 515 KBytes
[ 5] 9.00-10.00 sec 5.72 MBytes 48.2 Mbits/sec 0 515 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 58.3 MBytes 48.9 Mbits/sec 0 sender
[ 5] 0.00-10.00 sec 58.3 MBytes 48.9 Mbits/sec receiver
With the set I have:
root@LEDE:~# iperf3 -c 192.168.10.243
Connecting to host 192.168.10.243, port 5201
[ 5] local 192.168.10.1 port 45824 connected to 192.168.10.243 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 3.78 MBytes 31.7 Mbits/sec 0 197 KBytes
[ 5] 1.00-2.00 sec 3.71 MBytes 31.0 Mbits/sec 0 369 KBytes
[ 5] 2.00-3.00 sec 3.51 MBytes 29.5 Mbits/sec 0 484 KBytes
[ 5] 3.00-4.00 sec 3.36 MBytes 28.1 Mbits/sec 0 519 KBytes
[ 5] 4.00-5.00 sec 4.10 MBytes 34.4 Mbits/sec 0 519 KBytes
[ 5] 5.00-6.00 sec 3.73 MBytes 31.2 Mbits/sec 0 519 KBytes
[ 5] 6.00-7.00 sec 4.29 MBytes 36.0 Mbits/sec 0 519 KBytes
[ 5] 7.00-8.00 sec 4.16 MBytes 34.9 Mbits/sec 0 519 KBytes
[ 5] 8.00-9.00 sec 4.35 MBytes 36.5 Mbits/sec 0 519 KBytes
[ 5] 9.00-10.00 sec 4.41 MBytes 37.0 Mbits/sec 0 519 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 39.4 MBytes 33.0 Mbits/sec 0 sender
[ 5] 0.00-10.00 sec 39.4 MBytes 33.0 Mbits/sec receiver
Stanislaw
next prev parent reply other threads:[~2018-10-11 10:05 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-09 11:56 [PATCH v3 1/4] rt2x00: remove unneeded check Stanislaw Gruszka
2018-10-09 11:56 ` [PATCH v3 2/4] rt2x00: remove confusing AGC register Stanislaw Gruszka
2018-10-09 12:27 ` Daniel Golle
2018-10-09 12:47 ` Stanislaw Gruszka
2018-10-09 13:07 ` Daniel Golle
2018-10-09 13:23 ` Stanislaw Gruszka
2018-10-09 11:56 ` [PATCH v3 3/4] rt2x00: update TX_SW_CFG2 value Stanislaw Gruszka
2018-10-09 11:56 ` [PATCH v3 4/4] rt2800: fix registers init for MT7620 Stanislaw Gruszka
2018-10-09 23:27 ` Tom Psyborg
2018-10-10 7:14 ` Stanislaw Gruszka
2018-10-10 12:06 ` Daniel Golle
2018-10-10 12:45 ` Stanislaw Gruszka
2018-10-10 14:11 ` Tom Psyborg
2018-10-10 15:40 ` Stanislaw Gruszka
2018-10-10 20:03 ` Tom Psyborg
2018-10-11 10:05 ` Stanislaw Gruszka [this message]
2018-10-11 12:39 ` Tom Psyborg
2018-10-12 8:50 ` Stanislaw Gruszka
2018-10-11 10:06 ` [PATCH v3 1/4] rt2x00: remove unneeded check Stanislaw Gruszka
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181011100524.GA20794@redhat.com \
--to=sgruszka@redhat.com \
--cc=daniel@makrotopia.org \
--cc=dev@kresin.me \
--cc=linux-wireless@vger.kernel.org \
--cc=nbd@nbd.name \
--cc=pozega.tomislav@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.