From: Arnaldo Carvalho de Melo <acme@kernel.org>
To: Ingo Molnar <mingo@kernel.org>
Cc: Clark Williams <williams@redhat.com>,
linux-kernel@vger.kernel.org, linux-perf-users@vger.kernel.org,
Jiri Olsa <jolsa@redhat.com>, Jiri Olsa <jolsa@kernel.org>,
Alexander Shishkin <alexander.shishkin@linux.intel.com>,
Kan Liang <kan.liang@linux.intel.com>,
Namhyung Kim <namhyung@kernel.org>,
Peter Zijlstra <peterz@infradead.org>,
Arnaldo Carvalho de Melo <acme@redhat.com>
Subject: [PATCH 04/11] perf vendor events intel: Fix wrong filter_band* values for uncore events
Date: Wed, 17 Oct 2018 19:54:54 -0300 [thread overview]
Message-ID: <20181017225501.32150-5-acme@kernel.org> (raw)
In-Reply-To: <20181017225501.32150-1-acme@kernel.org>
From: Jiri Olsa <jolsa@redhat.com>
Michael reported that he could not stat following event:
$ perf stat -e unc_p_freq_ge_1200mhz_cycles -a -- ls
event syntax error: '..e_1200mhz_cycles'
\___ value too big for format, maximum is 255
Run 'perf list' for a list of valid events
The event is unwrapped into:
uncore_pcu/event=0xb,filter_band0=1200/
where filter_band0 format says it's one byte only:
# cat uncore_pcu/format/filter_band0
config1:0-7
while JSON files specifies bigger number:
"Filter": "filter_band0=1200",
all the filter_band* formats show 1 byte width:
# cat uncore_pcu/format/filter_band1
config1:8-15
# cat uncore_pcu/format/filter_band2
config1:16-23
# cat uncore_pcu/format/filter_band3
config1:24-31
The reason of the issue is that filter_band* values are supposed to be
in 100Mhz units.. it's stated in the JSON help for the events, like:
filter_band3=XXX, with XXX in 100Mhz units
This patch divides the filter_band* values by 100, plus there's couple
of changes that actually change the number completely, like:
- "Filter": "edge=1,filter_band2=4000",
+ "Filter": "edge=1,filter_band2=30",
Reported-by: Michael Petlan <mpetlan@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20181010080339.GB15790@krava
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
---
tools/perf/pmu-events/arch/x86/ivytown/uncore-power.json | 16 ++++++++--------
.../perf/pmu-events/arch/x86/jaketown/uncore-power.json | 16 ++++++++--------
2 files changed, 16 insertions(+), 16 deletions(-)
diff --git a/tools/perf/pmu-events/arch/x86/ivytown/uncore-power.json b/tools/perf/pmu-events/arch/x86/ivytown/uncore-power.json
index d40498f2cb1e..635c09fda1d9 100644
--- a/tools/perf/pmu-events/arch/x86/ivytown/uncore-power.json
+++ b/tools/perf/pmu-events/arch/x86/ivytown/uncore-power.json
@@ -188,7 +188,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xb",
"EventName": "UNC_P_FREQ_GE_1200MHZ_CYCLES",
- "Filter": "filter_band0=1200",
+ "Filter": "filter_band0=12",
"MetricExpr": "(UNC_P_FREQ_GE_1200MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_1200mhz_cycles %",
"PerPkg": "1",
@@ -199,7 +199,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xc",
"EventName": "UNC_P_FREQ_GE_2000MHZ_CYCLES",
- "Filter": "filter_band1=2000",
+ "Filter": "filter_band1=20",
"MetricExpr": "(UNC_P_FREQ_GE_2000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_2000mhz_cycles %",
"PerPkg": "1",
@@ -210,7 +210,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xd",
"EventName": "UNC_P_FREQ_GE_3000MHZ_CYCLES",
- "Filter": "filter_band2=3000",
+ "Filter": "filter_band2=30",
"MetricExpr": "(UNC_P_FREQ_GE_3000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_3000mhz_cycles %",
"PerPkg": "1",
@@ -221,7 +221,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xe",
"EventName": "UNC_P_FREQ_GE_4000MHZ_CYCLES",
- "Filter": "filter_band3=4000",
+ "Filter": "filter_band3=40",
"MetricExpr": "(UNC_P_FREQ_GE_4000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_4000mhz_cycles %",
"PerPkg": "1",
@@ -232,7 +232,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xb",
"EventName": "UNC_P_FREQ_GE_1200MHZ_TRANSITIONS",
- "Filter": "edge=1,filter_band0=1200",
+ "Filter": "edge=1,filter_band0=12",
"MetricExpr": "(UNC_P_FREQ_GE_1200MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_1200mhz_cycles %",
"PerPkg": "1",
@@ -243,7 +243,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xc",
"EventName": "UNC_P_FREQ_GE_2000MHZ_TRANSITIONS",
- "Filter": "edge=1,filter_band1=2000",
+ "Filter": "edge=1,filter_band1=20",
"MetricExpr": "(UNC_P_FREQ_GE_2000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_2000mhz_cycles %",
"PerPkg": "1",
@@ -254,7 +254,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xd",
"EventName": "UNC_P_FREQ_GE_3000MHZ_TRANSITIONS",
- "Filter": "edge=1,filter_band2=4000",
+ "Filter": "edge=1,filter_band2=30",
"MetricExpr": "(UNC_P_FREQ_GE_3000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_3000mhz_cycles %",
"PerPkg": "1",
@@ -265,7 +265,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xe",
"EventName": "UNC_P_FREQ_GE_4000MHZ_TRANSITIONS",
- "Filter": "edge=1,filter_band3=4000",
+ "Filter": "edge=1,filter_band3=40",
"MetricExpr": "(UNC_P_FREQ_GE_4000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_4000mhz_cycles %",
"PerPkg": "1",
diff --git a/tools/perf/pmu-events/arch/x86/jaketown/uncore-power.json b/tools/perf/pmu-events/arch/x86/jaketown/uncore-power.json
index 16034bfd06dd..8755693d86c6 100644
--- a/tools/perf/pmu-events/arch/x86/jaketown/uncore-power.json
+++ b/tools/perf/pmu-events/arch/x86/jaketown/uncore-power.json
@@ -187,7 +187,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xb",
"EventName": "UNC_P_FREQ_GE_1200MHZ_CYCLES",
- "Filter": "filter_band0=1200",
+ "Filter": "filter_band0=12",
"MetricExpr": "(UNC_P_FREQ_GE_1200MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_1200mhz_cycles %",
"PerPkg": "1",
@@ -198,7 +198,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xc",
"EventName": "UNC_P_FREQ_GE_2000MHZ_CYCLES",
- "Filter": "filter_band1=2000",
+ "Filter": "filter_band1=20",
"MetricExpr": "(UNC_P_FREQ_GE_2000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_2000mhz_cycles %",
"PerPkg": "1",
@@ -209,7 +209,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xd",
"EventName": "UNC_P_FREQ_GE_3000MHZ_CYCLES",
- "Filter": "filter_band2=3000",
+ "Filter": "filter_band2=30",
"MetricExpr": "(UNC_P_FREQ_GE_3000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_3000mhz_cycles %",
"PerPkg": "1",
@@ -220,7 +220,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xe",
"EventName": "UNC_P_FREQ_GE_4000MHZ_CYCLES",
- "Filter": "filter_band3=4000",
+ "Filter": "filter_band3=40",
"MetricExpr": "(UNC_P_FREQ_GE_4000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_4000mhz_cycles %",
"PerPkg": "1",
@@ -231,7 +231,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xb",
"EventName": "UNC_P_FREQ_GE_1200MHZ_TRANSITIONS",
- "Filter": "edge=1,filter_band0=1200",
+ "Filter": "edge=1,filter_band0=12",
"MetricExpr": "(UNC_P_FREQ_GE_1200MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_1200mhz_cycles %",
"PerPkg": "1",
@@ -242,7 +242,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xc",
"EventName": "UNC_P_FREQ_GE_2000MHZ_TRANSITIONS",
- "Filter": "edge=1,filter_band1=2000",
+ "Filter": "edge=1,filter_band1=20",
"MetricExpr": "(UNC_P_FREQ_GE_2000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_2000mhz_cycles %",
"PerPkg": "1",
@@ -253,7 +253,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xd",
"EventName": "UNC_P_FREQ_GE_3000MHZ_TRANSITIONS",
- "Filter": "edge=1,filter_band2=4000",
+ "Filter": "edge=1,filter_band2=30",
"MetricExpr": "(UNC_P_FREQ_GE_3000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_3000mhz_cycles %",
"PerPkg": "1",
@@ -264,7 +264,7 @@
"Counter": "0,1,2,3",
"EventCode": "0xe",
"EventName": "UNC_P_FREQ_GE_4000MHZ_TRANSITIONS",
- "Filter": "edge=1,filter_band3=4000",
+ "Filter": "edge=1,filter_band3=40",
"MetricExpr": "(UNC_P_FREQ_GE_4000MHZ_CYCLES / UNC_P_CLOCKTICKS) * 100.",
"MetricName": "freq_ge_4000mhz_cycles %",
"PerPkg": "1",
--
2.14.4
next prev parent reply other threads:[~2018-10-17 22:54 UTC|newest]
Thread overview: 23+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-17 22:54 [GIT PULL 00/11] perf/urgent fixes Arnaldo Carvalho de Melo
2018-10-17 22:54 ` Arnaldo Carvalho de Melo
2018-10-17 22:54 ` Arnaldo Carvalho de Melo
2018-10-17 22:54 ` [PATCH 01/11] tools arch uapi: Sync the x86 kvm.h copy Arnaldo Carvalho de Melo
2018-10-17 22:54 ` [PATCH 02/11] tools headers uapi: Sync " Arnaldo Carvalho de Melo
2018-10-17 22:54 ` [PATCH 03/11] Revert "perf tools: Fix PMU term format max value calculation" Arnaldo Carvalho de Melo
2018-10-17 22:54 ` Arnaldo Carvalho de Melo [this message]
2018-10-17 22:54 ` [PATCH 05/11] perf evsel: Store ids for events with their own cpus perf_event__synthesize_event_update_cpus Arnaldo Carvalho de Melo
2018-10-17 22:54 ` Arnaldo Carvalho de Melo
2018-10-17 22:54 ` [PATCH 06/11] perf tools: Fix use of alternatives to find JDIR Arnaldo Carvalho de Melo
2018-10-17 22:54 ` [PATCH 07/11] perf tools: Fix tracing_path_mount proper path Arnaldo Carvalho de Melo
2018-10-17 22:54 ` [PATCH 08/11] perf cpu_map: Align cpu map synthesized events properly Arnaldo Carvalho de Melo
2018-10-17 22:54 ` [PATCH 09/11] perf report: Don't crash on invalid inline debug information Arnaldo Carvalho de Melo
2018-10-17 22:55 ` [PATCH 10/11] perf tools: Pass build flags to traceevent build Arnaldo Carvalho de Melo
2018-10-17 22:55 ` [PATCH 11/11] perf tools: Stop fallbacking to kallsyms for vdso symbols lookup Arnaldo Carvalho de Melo
2018-10-18 6:20 ` Adrian Hunter
2018-10-26 23:19 ` Vinicius Costa Gomes
2018-10-27 11:05 ` Jiri Olsa
2018-10-27 20:09 ` Vinicius Costa Gomes
2018-10-28 21:10 ` Jiri Olsa
2018-10-18 5:44 ` [GIT PULL 00/11] perf/urgent fixes Ingo Molnar
2018-10-18 5:44 ` Ingo Molnar
2018-10-18 5:44 ` Ingo Molnar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181017225501.32150-5-acme@kernel.org \
--to=acme@kernel.org \
--cc=acme@redhat.com \
--cc=alexander.shishkin@linux.intel.com \
--cc=jolsa@kernel.org \
--cc=jolsa@redhat.com \
--cc=kan.liang@linux.intel.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-perf-users@vger.kernel.org \
--cc=mingo@kernel.org \
--cc=namhyung@kernel.org \
--cc=peterz@infradead.org \
--cc=williams@redhat.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.