From: Sasha Levin <sashal@kernel.org>
To: stable@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Yu Zhao <yuzhao@google.com>, Ulf Hansson <ulf.hansson@linaro.org>,
Sasha Levin <sashal@kernel.org>
Subject: [PATCH AUTOSEL 3.18 08/22] mmc: sdhci-pci-o2micro: Add quirk for O2 Micro dev 0x8620 rev 0x01
Date: Wed, 31 Oct 2018 19:11:52 -0400 [thread overview]
Message-ID: <20181031231206.29509-8-sashal@kernel.org> (raw)
In-Reply-To: <20181031231206.29509-1-sashal@kernel.org>
From: Yu Zhao <yuzhao@google.com>
[ Upstream commit 5169894982bb67486d93cc1e10151712bb86bcb6 ]
This device reports SDHCI_CLOCK_INT_STABLE even though it's not
ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading
SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the
bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 |
SDHCI_CLOCK_CARD_EN but only observed the first operand).
mmc1: Timeout waiting for hardware cmd interrupt.
mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00000603
mmc1: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
mmc1: sdhci: Present: 0x01ff0001 | Host ctl: 0x00000001
mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000000
mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03
mmc1: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
mmc1: sdhci: Int enab: 0x00ff0083 | Sig enab: 0x00ff0083
mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
mmc1: sdhci: Caps: 0x25fcc8bf | Caps_1: 0x00002077
mmc1: sdhci: Cmd: 0x00000000 | Max curr: 0x005800c8
mmc1: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000
mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
mmc1: sdhci: Host ctl2: 0x00000008
mmc1: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
mmc1: sdhci: ============================================
The problem happens during wakeup from S3. Adding a delay quirk
after power up reliably fixes the problem.
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/mmc/host/sdhci-pci-o2micro.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index e2ec108dba0e..a4b614a75ac0 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -336,6 +336,9 @@ int sdhci_pci_o2_probe(struct sdhci_pci_chip *chip)
pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
break;
case PCI_DEVICE_ID_O2_SEABIRD0:
+ if (chip->pdev->revision == 0x01)
+ chip->quirks |= SDHCI_QUIRK_DELAY_AFTER_POWER;
+ /* fall through */
case PCI_DEVICE_ID_O2_SEABIRD1:
/* UnLock WP */
ret = pci_read_config_byte(chip->pdev,
--
2.17.1
next prev parent reply other threads:[~2018-10-31 23:12 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-31 23:11 [PATCH AUTOSEL 3.18 01/22] locking/lockdep: Fix debug_locks off performance problem Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 02/22] ataflop: fix error handling during setup Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 03/22] swim: fix cleanup on setup error Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 04/22] tun: Consistently configure generic netdev params via rtnetlink Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 05/22] perf tools: Free temporary 'sys' string in read_event_files() Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 06/22] perf tools: Cleanup trace-event-info 'tdata' leak Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 07/22] cpupower: Fix coredump on VMWare Sasha Levin
2018-10-31 23:11 ` Sasha Levin [this message]
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 09/22] x86/olpc: Indicate that legacy PC XO-1 platform should not register RTC Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 10/22] regulator: fixed: Default enable high on DT regulators Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 11/22] x86: boot: Fix EFI stub alignment Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 12/22] kprobes: Return error if we fail to reuse kprobe instead of BUG_ON() Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 13/22] ath10k: schedule hardware restart if WMI command times out Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 14/22] scsi: esp_scsi: Track residual for PIO transfers Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 15/22] Drivers: hv: kvp: Fix two "this statement may fall through" warnings Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 16/22] ext4: fix argument checking in EXT4_IOC_MOVE_EXT Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 17/22] MD: fix invalid stored role for a disk Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 18/22] usb: chipidea: Prevent unbalanced IRQ disable Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 19/22] uio: ensure class is registered before devices Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 20/22] scsi: lpfc: Correct soft lockup when running mds diagnostics Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 21/22] signal: Always deliver the kernel's SIGKILL and SIGSTOP to a pid namespace init Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 22/22] mfd: menelaus: Fix possible race condition and leak Sasha Levin
2018-11-01 0:27 ` Alexandre Belloni
2018-11-01 1:29 ` Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181031231206.29509-8-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=stable@vger.kernel.org \
--cc=ulf.hansson@linaro.org \
--cc=yuzhao@google.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.