Re: [PATCH v3 1/2] dt-bindings/interrupt-controller: rzn1: Add RZ/N1 gpio irq mux binding

[Rob Herring <robh@kernel.org>]

On Tue, Nov 13, 2018 at 01:09:09PM +0000, Phil Edworthy wrote:
> Add device binding documentation for the Renesas RZ/N1 GPIO interrupt
> multiplexer.
> 
> Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
> ---
> v3:
>  - Use 'interrupt-map' DT property correctly.
> v2:
>  - Use interrupt-map to allow the GPIO controller info to be specified
>    as part of the irq.
>  - Don't show status in binding examples.
>  - Don't show the soc/board split in binding doc.
> ---
>  .../interrupt-controller/renesas,rzn1-mux.txt | 73 +++++++++++++++++++
>  1 file changed, 73 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt

A few nits, otherwise:

Reviewed-by: Rob Herring <robh@kernel.org>

> 
> diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt
> new file mode 100644
> index 000000000000..6515880e25cc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,rzn1-mux.txt
> @@ -0,0 +1,73 @@
> +* Renesas RZ/N1 GPIO Interrupt Multiplexer
> +
> +On Renesas RZ/N1 devices, there are several GPIO Controllers each with a number
> +of interrupt outputs. All of the interrupts from the GPIO Controllers are passed
> +to the GPIO Interrupt Multiplexer, which selects a sub-set of the interrupts to
> +pass onto the system interrupt controller.
> +
> +A single node in the device tree is used to describe the GPIO IRQ Muxer.
> +
> +Required properties:
> +- compatible: SoC-specific compatible string "renesas,<soc-specific>-gpioirqmux"
> +  followed by "renesas,rzn1-gpioirqmux" as fallback. The SoC-specific compatible
> +  strings must be one of:
> +	"renesas,r9a06g032-gpioirqmux" for RZ/N1D
> +	"renesas,r9a06g033-gpioirqmux" for RZ/N1S
> +- reg: Base address and size of GPIO IRQ Muxer registers.
> +- interrupts: List of output interrupts.
> +- #interrupt-cells: Numder of cells in the input interrupt specifier, must be 1.
> +- #address-cells: Must be 0.
> +- interrupt-map-mask: must be 127.
> +- interrupt-map: Standard property detailing the maps between input irqs and the
> +  corresponding output irq. This consist of a list of:
> +	<input-irq-spec phandle-to-interrupt-controller output-irq-spec>
> +  The input-irq-spec is from 0 to 95, corresponding to the outputs of the GPIO
> +  Controllers.
> +
> +Example:
> +
> +	The following is an example for the RZ/N1D SoC.
> +
> +	gpioirqmux: gpioirqmux@51000480 {

interrupt-controller@...

> +		compatible = "renesas,r9a06g032-gpioirqmux",
> +				"renesas,rzn1-gpioirqmux";
> +		reg = <0x51000480 0x20>;
> +		interrupts =
> +			<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
> +			<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;

This is a bit redundant as the same information is in interrupt-map, but 
I guess you need it to get the irq resources.

> +
> +		#interrupt-cells = <1>;
> +		#address-cells = <0>;
> +		interrupt-map-mask = <127>;

Use hex for masks.

> +		interrupt-map =
> +			/* gpio2a 24, pin 146: ETH Port 1 IRQ */
> +			<88 &gic GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
> +			/* gpio2a 26, pin 148: TouchSCRN_IRQ */
> +			<90 &gic GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	gpio2: gpio@5000d000 {
> +		compatible = "snps,dw-apb-gpio";
> +		reg = <0x5000d000 0x80>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		clock-names = "bus";
> +		clocks = <&sysctrl R9A06G032_HCLK_GPIO2>;
> +
> +		gpio2a: gpio-controller@0 {

gpio@0

> +			compatible = "snps,dw-apb-gpio-port";
> +			bank-name = "gpio2a";
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			snps,nr-gpios = <32>;
> +			reg = <0>;
> +
> +			interrupt-controller;
> +			interrupt-parent = <&gpioirqmux>;
> +			interrupts =  < 64 65 66 67 68 69 70 71
> +					72 73 74 75 76 77 78 79
> +					80 81 82 83 84 85 86 87
> +					88 89 90 91 92 93 94 95 >;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> -- 
> 2.17.1
>