From: Ladislav Michl <ladis@linux-mips.org>
To: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Barebox List <barebox@lists.infradead.org>
Subject: Re: [PATCH 00/23] AM3517 support
Date: Fri, 14 Dec 2018 17:22:49 +0100 [thread overview]
Message-ID: <20181214162249.GA19868@lenoch> (raw)
In-Reply-To: <20181214141730.26181-1-s.hauer@pengutronix.de>
Hello Sascha,
On Fri, Dec 14, 2018 at 03:17:07PM +0100, Sascha Hauer wrote:
> This series adds support for the TI AM3517 SoC along with Wago PFC-200
> board support. Also in this series some TI related driver patches. Most
> notably some significant chages to the GPMC Nand driver which was not
> really working anymore.
>
> Sascha
>
> Heinrich Toews (3):
> net: davinci-emac: fix buggy channel tear down
> net: davinci-emac: switch to device tree support
> ARM: omap: AM3517: Change default clock rate for AM3517
>
> Oleg Karfich (1):
> ARM: omap3: Add support for reset reason detection
>
> Sascha Hauer (19):
> net: davinci-emac: Add timeout to polling loop
> mci: omap: Improve error handling
> mci: omap: use IS_ENABLED() rather than #ifdef
> mtd: nand: omap: Use dev_dbg when a struct device * is available
> mtd: nand: omap: Fix hamming correct return values
> mtd: nand: omap: Disable subpage reads in hardware ecc mode
> mtd: nand: omap: remove unused function argument
> mtd: nand: omap: fix bch8_hw_romcode ecc layout
> mtd: nand: omap: set eccbytes correctly
> mtd: nand: omap: unbreak BCH8 support
may I point there is a MTD update pending on mailing list which,
once applied, would make merging with upstream drivers easier?
Yes, that upstream, which already fixed those bugs...
> ARM: omap: Add missing include
> ARM: omap: dmtimer: Turn into a driver
> ARM: omap: 32ktimer: Turn into a driver
> ARM: omap: Add AM35XX support
> ARM: omap: enable am33xx_uart_soft_reset for AM35xx
> ARM: omap: Add AM3517 specific mux configuration
> ARM: omap: Add emif4 support for AM3517
> ARM: omap: Add board support for WAGO pfc200 platform
> ARM: omap: am33xx_defconfig: Enable more boards and rename
>
> arch/arm/boards/Makefile | 1 +
> arch/arm/boards/wago-pfc-am35xx/Makefile | 6 +
> arch/arm/boards/wago-pfc-am35xx/board-mlo.c | 73 +++
> arch/arm/boards/wago-pfc-am35xx/board.c | 39 ++
> arch/arm/boards/wago-pfc-am35xx/lowlevel.c | 231 +++++++++
> .../arm/configs/am35xx_pfc200_xload_defconfig | 40 ++
> .../{am335x_defconfig => omap_defconfig} | 5 +-
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/am35xx-pfc-750_820x.dts | 487 ++++++++++++++++++
> arch/arm/dts/am3xxx-pfc-nandparts.dtsi | 63 +++
> arch/arm/mach-omap/Kconfig | 24 +-
> arch/arm/mach-omap/Makefile | 5 +-
> arch/arm/mach-omap/am33xx_generic.c | 32 +-
> arch/arm/mach-omap/am35xx_emif4.c | 85 +++
> arch/arm/mach-omap/am3xxx.c | 32 ++
> .../mach-omap/include/mach/am3xxx-silicon.h | 6 +
> arch/arm/mach-omap/include/mach/emif4.h | 105 ++++
> arch/arm/mach-omap/include/mach/omap3-clock.h | 2 +
> arch/arm/mach-omap/include/mach/omap3-mux.h | 49 +-
> arch/arm/mach-omap/include/mach/sys_info.h | 2 +
> arch/arm/mach-omap/omap3_clock.c | 16 +-
> arch/arm/mach-omap/omap3_generic.c | 58 ++-
> arch/arm/mach-omap/omap4_generic.c | 5 +-
> drivers/clocksource/Kconfig | 6 +
> drivers/clocksource/Makefile | 2 +
> .../clocksource/timer-ti-32k.c | 39 +-
> .../clocksource/timer-ti-dm.c | 47 +-
> drivers/mci/omap_hsmmc.c | 37 +-
> drivers/mtd/nand/nand_omap_gpmc.c | 141 +++--
> drivers/net/davinci_emac.c | 210 +++++---
> images/Makefile | 1 +
> images/Makefile.am35xx | 24 +
> include/platform_data/eth-davinci-emac.h | 10 -
> 33 files changed, 1657 insertions(+), 227 deletions(-)
> create mode 100644 arch/arm/boards/wago-pfc-am35xx/Makefile
> create mode 100644 arch/arm/boards/wago-pfc-am35xx/board-mlo.c
> create mode 100644 arch/arm/boards/wago-pfc-am35xx/board.c
> create mode 100644 arch/arm/boards/wago-pfc-am35xx/lowlevel.c
> create mode 100644 arch/arm/configs/am35xx_pfc200_xload_defconfig
> rename arch/arm/configs/{am335x_defconfig => omap_defconfig} (96%)
> create mode 100644 arch/arm/dts/am35xx-pfc-750_820x.dts
> create mode 100644 arch/arm/dts/am3xxx-pfc-nandparts.dtsi
> create mode 100644 arch/arm/mach-omap/am35xx_emif4.c
> create mode 100644 arch/arm/mach-omap/am3xxx.c
> create mode 100644 arch/arm/mach-omap/include/mach/am3xxx-silicon.h
> create mode 100644 arch/arm/mach-omap/include/mach/emif4.h
> rename arch/arm/mach-omap/s32k_clksource.c => drivers/clocksource/timer-ti-32k.c (73%)
> rename arch/arm/mach-omap/dmtimer.c => drivers/clocksource/timer-ti-dm.c (72%)
> create mode 100644 images/Makefile.am35xx
> delete mode 100644 include/platform_data/eth-davinci-emac.h
>
> --
> 2.19.1
>
>
> _______________________________________________
> barebox mailing list
> barebox@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/barebox
_______________________________________________
barebox mailing list
barebox@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/barebox
next prev parent reply other threads:[~2018-12-14 16:23 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-14 14:17 [PATCH 00/23] AM3517 support Sascha Hauer
2018-12-14 14:17 ` [PATCH 01/23] net: davinci-emac: fix buggy channel tear down Sascha Hauer
2018-12-14 14:17 ` [PATCH 02/23] net: davinci-emac: Add timeout to polling loop Sascha Hauer
2018-12-14 14:17 ` [PATCH 03/23] net: davinci-emac: switch to device tree support Sascha Hauer
2018-12-14 14:17 ` [PATCH 04/23] mci: omap: Improve error handling Sascha Hauer
2018-12-14 14:17 ` [PATCH 05/23] mci: omap: use IS_ENABLED() rather than #ifdef Sascha Hauer
2018-12-14 14:17 ` [PATCH 06/23] mtd: nand: omap: Use dev_dbg when a struct device * is available Sascha Hauer
2018-12-14 14:17 ` [PATCH 07/23] mtd: nand: omap: Fix hamming correct return values Sascha Hauer
2018-12-14 14:17 ` [PATCH 08/23] mtd: nand: omap: Disable subpage reads in hardware ecc mode Sascha Hauer
2018-12-14 14:17 ` [PATCH 09/23] mtd: nand: omap: remove unused function argument Sascha Hauer
2018-12-14 14:17 ` [PATCH 10/23] mtd: nand: omap: fix bch8_hw_romcode ecc layout Sascha Hauer
2018-12-14 14:17 ` [PATCH 11/23] mtd: nand: omap: set eccbytes correctly Sascha Hauer
2018-12-14 14:17 ` [PATCH 12/23] mtd: nand: omap: unbreak BCH8 support Sascha Hauer
2018-12-14 14:17 ` [PATCH 13/23] ARM: omap: Add missing include Sascha Hauer
2018-12-14 14:17 ` [PATCH 14/23] ARM: omap: dmtimer: Turn into a driver Sascha Hauer
2018-12-17 13:37 ` Teresa Remmet
2018-12-18 7:46 ` Sascha Hauer
2018-12-14 14:17 ` [PATCH 15/23] ARM: omap: 32ktimer: " Sascha Hauer
2018-12-14 14:17 ` [PATCH 16/23] ARM: omap: Add AM35XX support Sascha Hauer
2018-12-14 14:17 ` [PATCH 17/23] ARM: omap: enable am33xx_uart_soft_reset for AM35xx Sascha Hauer
2018-12-14 14:17 ` [PATCH 18/23] ARM: omap3: Add support for reset reason detection Sascha Hauer
2018-12-14 14:17 ` [PATCH 19/23] ARM: omap: Add AM3517 specific mux configuration Sascha Hauer
2018-12-14 14:17 ` [PATCH 20/23] ARM: omap: Add emif4 support for AM3517 Sascha Hauer
2018-12-14 14:17 ` [PATCH 21/23] ARM: omap: AM3517: Change default clock rate " Sascha Hauer
2018-12-14 14:17 ` [PATCH 22/23] ARM: omap: Add board support for WAGO pfc200 platform Sascha Hauer
2019-01-07 11:40 ` Heinrich.Toews
2019-01-07 11:46 ` Sascha Hauer
2018-12-14 14:17 ` [PATCH 23/23] ARM: omap: am33xx_defconfig: Enable more boards and rename Sascha Hauer
2018-12-14 16:22 ` Ladislav Michl [this message]
2018-12-14 19:32 ` [PATCH 00/23] AM3517 support Sascha Hauer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181214162249.GA19868@lenoch \
--to=ladis@linux-mips.org \
--cc=barebox@lists.infradead.org \
--cc=s.hauer@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.