All of lore.kernel.org
 help / color / mirror / Atom feed
From: David Lechner <david@lechnology.com>
To: linux-spi@vger.kernel.org
Cc: David Lechner <david@lechnology.com>,
	Mark Brown <broonie@kernel.org>,
	linux-kernel@vger.kernel.org, Vignesh R <vigneshr@ti.com>
Subject: [PATCH] Revert "spi: omap2-mcspi: Set FIFO DMA trigger level to word length"
Date: Sun, 13 Jan 2019 14:49:05 -0600	[thread overview]
Message-ID: <20190113204905.29795-1-david@lechnology.com> (raw)

This reverts commit b682cffa3ac6d9d9e16e9b413c45caee3b391fab.

That commit breaks displays using tinydrm drivers, such as ili9225.

It causes corruption in the image that is displayed (it looks like only
1/2 of the framebuffer data is sent, the other half of the display
remains blank.)

The following error appears multiple times:

    ili9225 spi1.0: EOW timed out

Eventually, the system locks up without any additional errors.

Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
---
 drivers/spi/spi-omap2-mcspi.c | 26 +++++++++++++++++++-------
 1 file changed, 19 insertions(+), 7 deletions(-)

diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index 2fd8881fcd65..5a3854ff2e08 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -306,7 +306,7 @@ static void omap2_mcspi_set_fifo(const struct spi_device *spi,
 	struct omap2_mcspi_cs *cs = spi->controller_state;
 	struct omap2_mcspi *mcspi;
 	unsigned int wcnt;
-	int max_fifo_depth, bytes_per_word;
+	int max_fifo_depth, fifo_depth, bytes_per_word;
 	u32 chconf, xferlevel;
 
 	mcspi = spi_master_get_devdata(master);
@@ -322,6 +322,10 @@ static void omap2_mcspi_set_fifo(const struct spi_device *spi,
 		else
 			max_fifo_depth = OMAP2_MCSPI_MAX_FIFODEPTH;
 
+		fifo_depth = gcd(t->len, max_fifo_depth);
+		if (fifo_depth < 2 || fifo_depth % bytes_per_word != 0)
+			goto disable_fifo;
+
 		wcnt = t->len / bytes_per_word;
 		if (wcnt > OMAP2_MCSPI_MAX_FIFOWCNT)
 			goto disable_fifo;
@@ -329,17 +333,16 @@ static void omap2_mcspi_set_fifo(const struct spi_device *spi,
 		xferlevel = wcnt << 16;
 		if (t->rx_buf != NULL) {
 			chconf |= OMAP2_MCSPI_CHCONF_FFER;
-			xferlevel |= (bytes_per_word - 1) << 8;
+			xferlevel |= (fifo_depth - 1) << 8;
 		}
-
 		if (t->tx_buf != NULL) {
 			chconf |= OMAP2_MCSPI_CHCONF_FFET;
-			xferlevel |= bytes_per_word - 1;
+			xferlevel |= fifo_depth - 1;
 		}
 
 		mcspi_write_reg(master, OMAP2_MCSPI_XFERLEVEL, xferlevel);
 		mcspi_write_chconf0(spi, chconf);
-		mcspi->fifo_depth = max_fifo_depth;
+		mcspi->fifo_depth = fifo_depth;
 
 		return;
 	}
@@ -598,6 +601,7 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer)
 	struct dma_slave_config	cfg;
 	enum dma_slave_buswidth width;
 	unsigned es;
+	u32			burst;
 	void __iomem		*chstat_reg;
 	void __iomem            *irqstat_reg;
 	int			wait_res;
@@ -617,14 +621,22 @@ omap2_mcspi_txrx_dma(struct spi_device *spi, struct spi_transfer *xfer)
 	}
 
 	count = xfer->len;
+	burst = 1;
+
+	if (mcspi->fifo_depth > 0) {
+		if (count > mcspi->fifo_depth)
+			burst = mcspi->fifo_depth / es;
+		else
+			burst = count / es;
+	}
 
 	memset(&cfg, 0, sizeof(cfg));
 	cfg.src_addr = cs->phys + OMAP2_MCSPI_RX0;
 	cfg.dst_addr = cs->phys + OMAP2_MCSPI_TX0;
 	cfg.src_addr_width = width;
 	cfg.dst_addr_width = width;
-	cfg.src_maxburst = es;
-	cfg.dst_maxburst = es;
+	cfg.src_maxburst = burst;
+	cfg.dst_maxburst = burst;
 
 	rx = xfer->rx_buf;
 	tx = xfer->tx_buf;
-- 
2.17.1

             reply	other threads:[~2019-01-13 20:49 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-01-13 20:49 David Lechner [this message]
2019-01-13 20:52 ` [PATCH] Revert "spi: omap2-mcspi: Set FIFO DMA trigger level to word length" David Lechner
2019-01-14 12:30 ` Vignesh R
2019-01-14 23:50   ` David Lechner
2019-01-15  0:07     ` Mark Brown
2019-01-14 23:57   ` David Lechner

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190113204905.29795-1-david@lechnology.com \
    --to=david@lechnology.com \
    --cc=broonie@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.