From: Shawn Guo <shawnguo@kernel.org>
To: Alison Wang <alison.wang@nxp.com>
Cc: leoyang.li@nxp.com, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH] arm64: dts: ls1028a: Add Audio DT nodes
Date: Fri, 1 Feb 2019 12:50:05 +0800 [thread overview]
Message-ID: <20190201045002.GH19882@dragon> (raw)
In-Reply-To: <20190123052135.26829-1-alison.wang@nxp.com>
On Wed, Jan 23, 2019 at 01:21:35PM +0800, Alison Wang wrote:
> This patch adds Audio DT nodes for LS1028ARDB and LS1028AQDS boards.
>
> Signed-off-by: Alison Wang <alison.wang@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 62 ++++++++++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 63 +++++++++++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 57 +++++++++++++++++++
> 3 files changed, 182 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> index 14c79f4..139728e 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
> @@ -32,6 +32,49 @@
> device_type = "memory";
> reg = <0x0 0x80000000 0x1 0x00000000>;
> };
> +
> + sys_mclk: clock-mclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <25000000>;
> + };
> +
> + reg_1p8v: regulator-1p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "1P8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Headphone", "Headphone Jack",
> + "Speaker", "Speaker Ext",
> + "Line", "Line In Jack";
> + simple-audio-card,routing =
> + "MIC_IN", "Microphone Jack",
> + "Microphone Jack", "Mic Bias",
> + "LINE_IN", "Line In Jack",
> + "Headphone Jack", "HP_OUT",
> + "Speaker Ext", "LINE_OUT";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&sai1>;
> + frame-master;
> + bitclock-master;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&codec>;
> + frame-master;
> + bitclock-master;
> + system-clock-frequency = <25000000>;
> + };
> + };
> };
>
> &duart0 {
> @@ -89,5 +132,24 @@
> reg = <0x57>;
> };
> };
> +
> + i2c@5 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x5>;
> +
> + codec: sgtl5000@a {
sgtl5000: audio-codec@a
> + #sound-dai-cells = <0>;
> + compatible = "fsl,sgtl5000";
> + reg = <0xa>;
> + VDDA-supply = <®_1p8v>;
> + VDDIO-supply = <®_1p8v>;
> + clocks = <&sys_mclk>;
> + };
> + };
> };
> };
> +
> +&sai1 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> index fdeb417..1b3d5e3 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
> @@ -28,6 +28,49 @@
> device_type = "memory";
> reg = <0x0 0x80000000 0x1 0x0000000>;
> };
> +
> + sys_mclk: clock-mclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <25000000>;
> + };
> +
> + reg_1p8v: regulator-1p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "1P8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + sound {
> + compatible = "simple-audio-card";
> + simple-audio-card,format = "i2s";
> + simple-audio-card,widgets =
> + "Microphone", "Microphone Jack",
> + "Headphone", "Headphone Jack",
> + "Speaker", "Speaker Ext",
> + "Line", "Line In Jack";
> + simple-audio-card,routing =
> + "MIC_IN", "Microphone Jack",
> + "Microphone Jack", "Mic Bias",
> + "LINE_IN", "Line In Jack",
> + "Headphone Jack", "HP_OUT",
> + "Speaker Ext", "LINE_OUT";
> +
> + simple-audio-card,cpu {
> + sound-dai = <&sai4>;
> + frame-master;
> + bitclock-master;
> + };
> +
> + simple-audio-card,codec {
> + sound-dai = <&codec>;
> + frame-master;
> + bitclock-master;
> + system-clock-frequency = <25000000>;
> + };
> + };
> };
>
> &i2c0 {
> @@ -39,6 +82,22 @@
> #address-cells = <1>;
> #size-cells = <0>;
>
> + i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x1>;
> +
> + codec: sgtl5000@a {
> + #sound-dai-cells = <0>;
> + compatible = "fsl,sgtl5000";
> + reg = <0xa>;
> + VDDA-supply = <®_1p8v>;
> + VDDIO-supply = <®_1p8v>;
> + clocks = <&sys_mclk>;
> + sclk-strength = <3>;
What is this property?
> + };
> + };
> +
> i2c@2 {
> #address-cells = <1>;
> #size-cells = <0>;
> @@ -71,3 +130,7 @@
> &duart1 {
> status = "okay";
> };
> +
> +&sai4 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> index a8cf92a..48c9e3a 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
> @@ -335,5 +335,62 @@
> <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
> <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
> };
> +
> + edma0: edma@22c0000 {
dma-controller
> + #dma-cells = <2>;
> + compatible = "fsl,vf610-edma";
> + reg = <0x0 0x22c0000 0x0 0x10000>,
> + <0x0 0x22d0000 0x0 0x10000>,
> + <0x0 0x22e0000 0x0 0x10000>;
> + interrupts = <0 56 0x4>,
> + <0 56 0x4>;
Use GIC_SPI and IRQ_TYPE_LEVEL_HIGH.
> + interrupt-names = "edma-tx", "edma-err";
> + dma-channels = <32>;
> + clock-names = "dmamux0", "dmamux1";
> + clocks = <&clockgen 4 1>,
> + <&clockgen 4 1>;
> + };
> +
> + sai1: sai@f100000 {
audio-controller
Shawn
> + #sound-dai-cells = <0>;
> + compatible = "fsl,vf610-sai";
> + reg = <0x0 0xf100000 0x0 0x10000>;
> + interrupts = <0 82 0x4>;
> + clocks = <&clockgen 4 1>, <&clockgen 4 1>,
> + <&clockgen 4 1>, <&clockgen 4 1>;
> + clock-names = "bus", "mclk1", "mclk2", "mclk3";
> + dma-names = "tx", "rx";
> + dmas = <&edma0 1 4>,
> + <&edma0 1 3>;
> + status = "disabled";
> + };
> +
> + sai2: sai@f110000 {
> + #sound-dai-cells = <0>;
> + compatible = "fsl,vf610-sai";
> + reg = <0x0 0xf110000 0x0 0x10000>;
> + interrupts = <0 82 0x4>;
> + clocks = <&clockgen 4 1>, <&clockgen 4 1>,
> + <&clockgen 4 1>, <&clockgen 4 1>;
> + clock-names = "bus", "mclk1", "mclk2", "mclk3";
> + dma-names = "tx", "rx";
> + dmas = <&edma0 1 6>,
> + <&edma0 1 5>;
> + status = "disabled";
> + };
> +
> + sai4: sai@f130000 {
> + #sound-dai-cells = <0>;
> + compatible = "fsl,vf610-sai";
> + reg = <0x0 0xf130000 0x0 0x10000>;
> + interrupts = <0 83 0x4>;
> + clocks = <&clockgen 4 1>, <&clockgen 4 1>,
> + <&clockgen 4 1>, <&clockgen 4 1>;
> + clock-names = "bus", "mclk1", "mclk2", "mclk3";
> + dma-names = "tx", "rx";
> + dmas = <&edma0 1 10>,
> + <&edma0 1 9>;
> + status = "disabled";
> + };
> };
> };
> --
> 1.7.1
>
next prev parent reply other threads:[~2019-02-01 4:50 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-23 5:21 [PATCH] arm64: dts: ls1028a: Add Audio DT nodes Alison Wang
2019-02-01 4:50 ` Shawn Guo [this message]
2019-02-20 8:12 ` Alison Wang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190201045002.GH19882@dragon \
--to=shawnguo@kernel.org \
--cc=alison.wang@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=leoyang.li@nxp.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.