Re: [PATCH 15/15] arm64: dts: marvell: Convert 7k/8k usb-phy properties to phy-supply

[Miquel Raynal <miquel.raynal@bootlin.com>]

Hi Martin,

Rob, a few questions for you below :)

Martin Blumenstingl <martin.blumenstingl@googlemail.com> wrote on Tue,
2 Apr 2019 21:35:26 +0200:

> Hi Miquel,
> 
> thank you for keeping me in the loop!
> 
> On Mon, Apr 1, 2019 at 6:52 PM Miquel Raynal <miquel.raynal@bootlin.com> wrote:
> >
> > Update Aramda 7k/8k DTs to use the phy-supply property of the (recent)
> > generic PHY framework instead of the (legacy) usb-phy preperty. Both
> > enable the supply when the PHY is enabled.
> >
> > The COMPHY nodes only provide SERDES lanes configuration. The power
> > supply that is represented by the phy-supply property is just a
> > regulator wired to the USB connector, hence the creation of connector
> > nodes as child of the COMPHY nodes and the supply attached to it.  
> shouldn't this also be reflected in the dt-bindings?

I don't think it deserves an update in the bindings as this is just an
update for a better hardware representation. The COMPHY block is
already documented, the connector one too. I thought adding a connector
node in the COMPHY node was okay when I read Rob's answer to your
series as this has nothing to do with the IP itself but is just
describing how the board is built. Maybe Rob can confirm this?

> 
> > Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> > Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> > ---
> >  .../arm64/boot/dts/marvell/armada-7040-db.dts | 26 ++++++++++---------
> >  .../marvell/armada-8040-clearfog-gt-8k.dts    | 13 +++++-----
> >  .../arm64/boot/dts/marvell/armada-8040-db.dts | 13 +++++-----
> >  .../boot/dts/marvell/armada-8040-mcbin.dtsi   | 13 +++++-----
> >  4 files changed, 35 insertions(+), 30 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/marvell/armada-7040-db.dts b/arch/arm64/boot/dts/marvell/armada-7040-db.dts
> > index 131ce4229db0..4b8df359b1cc 100644
> > --- a/arch/arm64/boot/dts/marvell/armada-7040-db.dts
> > +++ b/arch/arm64/boot/dts/marvell/armada-7040-db.dts
> > @@ -45,16 +45,6 @@
> >                 enable-active-high;
> >                 gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
> >         };
> > -
> > -       cp0_usb3_0_phy: cp0-usb3-0-phy {
> > -               compatible = "usb-nop-xceiv";
> > -               vcc-supply = <&cp0_reg_usb3_0_vbus>;
> > -       };
> > -
> > -       cp0_usb3_1_phy: cp0-usb3-1-phy {
> > -               compatible = "usb-nop-xceiv";
> > -               vcc-supply = <&cp0_reg_usb3_1_vbus>;
> > -       };
> >  };
> >
> >  &i2c0 {
> > @@ -200,15 +190,27 @@
> >         };
> >  };
> >
> > +&cp0_comphy1 {
> > +       cp0_usbh0_con: connector {
> > +               compatible = "usb-a-connector";
> > +               phy-supply = <&cp0_reg_usb3_0_vbus>;
> > +       };
> > +};  
> (disclaimer: I don't have any board with a marvell SoC, so I don't
> understand how it works and I can't debug it)
> I know about the "phy-supply" property inside the PHY node itself
> (that would be cp0_comphy1 in this case).
> The connector binding does not mention a phy-supply property:
> Documentation/devicetree/bindings/connector/usb-connector.txt

That's right, can Rob confirm that this is valid? If yes I can add an
optional "phy-supply" property there.

> I don't understand which driver enables the phy-supply when it's part
> of a "connector" child-node.
> do you have a hint where I should start looking?

I honestly have no idea, but apparently it works.


Thanks,
Miquèl

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel